main
Ray
Publish 0.1.0
2b0ba8d
LT8606IMSE#TRPBF
Analog Devices · DC-DC Converters · MSOP-10-EP
LT8606IMSE#TRPBF from Analog Devices, in a MSOP-10-EP. Pinout and pin descriptions extracted from the manufacturer datasheet (extract_pins, cross-checked by a second model); symbol, footprint, and 3D from KiCad-official CAD.
Pinout
| Pin | Name | Type | Function |
|---|---|---|---|
| 1 | BST | power_out | Provides a drive voltage higher than the input voltage to the topside power switch, so a 0.1µF boost capacitor must be placed as close as possible to the IC with no series resistor. |
| 2 | SW | output | Output of the internal power switches that connects to the inductor and boost capacitor, and this node should be kept small on the PCB for good performance. |
| 3 | INTVCC | power_out | Internal 3.5V regulator bypass pin with maximum output current of 20mA that varies between 2.8V and 3.5V, to be decoupled with at least a 1µF low ESR ceramic capacitor and not loaded externally. |
| 4 | RT | passive | A resistor tied between RT and ground sets the switching frequency, and when synchronizing it must set the frequency at or below the lowest synchronization input. |
| 5 | SYNC | input | External clock synchronization input (MSOP only) that is grounded for Burst Mode operation, left floating for pulse-skipping mode, or tied to a clock or to a voltage between 3.2V and 5.0V for pulse-skipping with spread spectrum. |
| 6 | FB | input | The LT8606 regulates this pin to 0.778V, and the feedback resistor divider tap connects to it. |
| 7 | TR/SS | passive | Output tracking and soft-start pin (MSOP only) with an internal 2µA pull-up from INTVCC, pulled to ground through a 300Ω MOSFET during shutdown and fault conditions, so a series resistor is needed when driven from a low impedance output. |
| 8 | PG | output | Open-drain power good output that remains low until FB is within ±8.5% of the regulation voltage with no fault conditions, and is pulled low when VIN is above 3.2V and EN/UV is low. |
| 9 | VIN | power_in | Supplies current to the internal circuitry and the internal topside power switch, and must be locally bypassed with the input capacitor positive terminal placed as close as possible to the VIN pins. |
| 10 | EN/UV | input | Shuts the LT8606 down when low and enables it when high, with a hysteretic threshold of 1.05V rising and 1.00V falling, and it is tied to VIN if the shutdown feature is not used. |
| 11 | GND | power_in | Exposed pad that must be connected to the negative terminal of the input capacitor and soldered to the PCB to lower the thermal resistance. |
Key specifications
| Parameter | Value |
|---|---|
| Manufacturer | Analog Devices |
| Package | MSOP-10-EP |
| Category | Power Supply Chip |
| Pins | 11 |
Electrical characteristics
Limits as printed in the datasheet (page.json metadata.characteristics carries them as data).
| Parameter | Symbol | Min | Typ | Max | Unit | Conditions | Page |
|---|---|---|---|---|---|---|---|
| Minimum Input Voltage | 2.5 | 3 | 3.2 | V | 3 | ||
| VIN Quiescent Current (shutdown) | 1 | 1.7 | µA | VEN/UV = 0V | 3 | ||
| VIN Quiescent Current (not switching) | 5 | 12 | µA | VEN/UV = 2V, Not Switching, VSYNC = 0V or LT8606 DFN, VIN ≤ 36V | 3 | ||
| VIN Current in Regulation | 56 | 90 | µA | VIN = 6V, VOUT = 2.7V, Output Load = 100µA | 3 | ||
| VIN Current in Regulation | 500 | 700 | µA | VIN = 6V, VOUT = 2.7V, Output Load = 1mA | 3 | ||
| Feedback Reference Voltage MSOP Package | 0.774 | 0.778 | 0.782 | V | VIN = 6V, ILOAD = 100mA | 3 | |
| Feedback Reference Voltage MSOP Package | 0.762 | 0.778 | 0.798 | V | VIN = 6V, ILOAD = 100mA (l, full operating temperature range) | 3 | |
| Feedback Voltage Line Regulation | -0.06 | 0.02 | 0.06 | %/V | VIN = 4.0V to 40V (l) | 3 | |
| Feedback Pin Input Current | -20 | 20 | nA | VFB = 1V | 3 | ||
| Minimum On-Time | 35 | 65 | ns | ILOAD = 300mA, SYNC = 0V or LT8606 DFN (l) | 3 | ||
| Minimum On-Time | 35 | 60 | ns | ILOAD = 300mA, SYNC = 1.9V or LT8606B DFN (l) | 3 | ||
| Minimum Off Time | 93 | 130 | ns | ILOAD = 300mA (l) | 3 | ||
| Oscillator Frequency MSOP Package | 155 | 200 | 245 | kHz | RT = 221k, ILOAD = 250mA (l) | 3 | |
| Oscillator Frequency MSOP Package | 640 | 700 | 760 | kHz | RT = 60.4k, ILOAD = 250mA (l) | 3 | |
| Oscillator Frequency MSOP Package | 1.9 | 2 | 2.1 | MHz | RT = 18.2k, ILOAD = 250mA (l) | 3 | |
| Top Power NMOS Current Limit MSOP Package | 0.65 | 0.9 | 1.15 | A | MSOP Package (l) | 3 | |
| Top Power NMOS On-Resistance | 375 | mΩ | ILOAD = 250mA | 3 | |||
| Bottom Power NMOS On-Resistance | 240 | mΩ | 3 | ||||
| SW Leakage Current | 5 | µA | VIN = 36V | 3 | |||
| EN/UV Pin Threshold | 0.99 | 1.05 | 1.11 | V | EN/UV Rising (l) | 3 | |
| EN/UV Pin Hysteresis | 50 | mV | 3 | ||||
| EN/UV Pin Current | -20 | 20 | nA | VEN/UV = 2V | 3 | ||
| PG Upper Threshold Offset from VFB | 5 | 8.5 | 13 | % | VFB Rising (l) | 3 | |
| PG Lower Threshold Offset from VFB | 5 | 8.5 | 13 | % | VFB Falling (l) | 3 | |
| PG Hysteresis | 0.5 | % | 3 | ||||
| PG Leakage | -200 | 200 | nA | VPG = 42V | 3 | ||
| PG Pull-Down Resistance | 550 | 1200 | Ω | VPG = 0.1V | 3 | ||
| Sync Low Input Voltage | 0.4 | 0.9 | V | MSOP Only (l) | 3 | ||
| Sync High Input Voltage | 2.7 | 3.2 | V | INTVCC = 3.5V, MSOP Only (l) | 3 | ||
| TR/SS Source Current | 1 | 2 | 3 | µA | MSOP Only (l) | 3 | |
| TR/SS Pull-Down Resistance | 300 | 900 | Ω | Fault Condition, TR/SS = 0.1V, MSOP Only | 3 | ||
| Spread Spectrum Modulation Frequency | 0.5 | 3 | 6 | kHz | VSYNC = 3.3V, MSOP Only | 3 | |
| VIN, EN/UV, PG Absolute Maximum Voltage | 42 | V | 2 | ||||
| FB, TR/SS Absolute Maximum Voltage | 4 | V | 2 | ||||
| SYNC Absolute Maximum Voltage | 6 | V | 2 | ||||
| Operating Junction Temperature Range | -40 | 125 | °C | LT8606I | 2 | ||
| Storage Temperature Range | -65 | 150 | °C | 2 | |||
| Thermal Resistance Junction-to-Ambient | θJA | 40 | °C/W | MSE PACKAGE, 10-LEAD PLASTIC MSOP | 2 |
CAD (KiCad official)
- Symbol:
LT8606IMSE#TRPBF - Footprint:
Package_SO:MSOP-10-1EP_3x3mm_P0.5mm_EP1.68x1.88mm - 3D model: MSOP-10-EP (KiCad packages3D, STEP)
- 3D model files:
lt8606imse-trpbf-etched.step/lt8606imse-trpbf-etched.glbcarry the MPN laser-etched on the die in a toggleableAdom.LaserEtchgroup (Fusion-ready);lt8606imse-trpbf.step/lt8606imse-trpbf.glbare the bare package body.
Provenance
Data extracted from the manufacturer datasheet, not a distributor listing:
- Datasheet: Analog Devices datasheet (24 pp, sha256
cfaa3e87d6a68cc5, retrieved 2026-10-28, tier: manufacturer) - Extractor: parts-factory
2.0.0/extract_pins 0.3, primaryclaude-haiku-5-5(text), consensusclaude-sonnet-5-5(agreed), guards: pin_guards 0.1: passed. Pins are checked against the footprint pad set and their cited datasheet pages before publish. - CAD: KiCad official libraries (CC-BY-SA 4.0).
# LT8606IMSE#TRPBF
**Analog Devices** · DC-DC Converters · MSOP-10-EP
LT8606IMSE#TRPBF from Analog Devices, in a MSOP-10-EP. Pinout and pin descriptions extracted from the manufacturer datasheet (extract_pins, cross-checked by a second model); symbol, footprint, and 3D from KiCad-official CAD.
## Pinout
| Pin | Name | Type | Function |
|---|---|---|---|
| 1 | BST | power_out | Provides a drive voltage higher than the input voltage to the topside power switch, so a 0.1µF boost capacitor must be placed as close as possible to the IC with no series resistor. |
| 2 | SW | output | Output of the internal power switches that connects to the inductor and boost capacitor, and this node should be kept small on the PCB for good performance. |
| 3 | INTVCC | power_out | Internal 3.5V regulator bypass pin with maximum output current of 20mA that varies between 2.8V and 3.5V, to be decoupled with at least a 1µF low ESR ceramic capacitor and not loaded externally. |
| 4 | RT | passive | A resistor tied between RT and ground sets the switching frequency, and when synchronizing it must set the frequency at or below the lowest synchronization input. |
| 5 | SYNC | input | External clock synchronization input (MSOP only) that is grounded for Burst Mode operation, left floating for pulse-skipping mode, or tied to a clock or to a voltage between 3.2V and 5.0V for pulse-skipping with spread spectrum. |
| 6 | FB | input | The LT8606 regulates this pin to 0.778V, and the feedback resistor divider tap connects to it. |
| 7 | TR/SS | passive | Output tracking and soft-start pin (MSOP only) with an internal 2µA pull-up from INTVCC, pulled to ground through a 300Ω MOSFET during shutdown and fault conditions, so a series resistor is needed when driven from a low impedance output. |
| 8 | PG | output | Open-drain power good output that remains low until FB is within ±8.5% of the regulation voltage with no fault conditions, and is pulled low when VIN is above 3.2V and EN/UV is low. |
| 9 | VIN | power_in | Supplies current to the internal circuitry and the internal topside power switch, and must be locally bypassed with the input capacitor positive terminal placed as close as possible to the VIN pins. |
| 10 | EN/UV | input | Shuts the LT8606 down when low and enables it when high, with a hysteretic threshold of 1.05V rising and 1.00V falling, and it is tied to VIN if the shutdown feature is not used. |
| 11 | GND | power_in | Exposed pad that must be connected to the negative terminal of the input capacitor and soldered to the PCB to lower the thermal resistance. |
## Key specifications
| Parameter | Value |
|---|---|
| Manufacturer | Analog Devices |
| Package | MSOP-10-EP |
| Category | Power Supply Chip |
| Pins | 11 |
## Electrical characteristics
Limits as printed in the datasheet (page.json `metadata.characteristics` carries them as data).
| Parameter | Symbol | Min | Typ | Max | Unit | Conditions | Page |
|---|---|---|---|---|---|---|---|
| Minimum Input Voltage | | 2.5 | 3 | 3.2 | V | | 3 |
| VIN Quiescent Current (shutdown) | | | 1 | 1.7 | µA | VEN/UV = 0V | 3 |
| VIN Quiescent Current (not switching) | | | 5 | 12 | µA | VEN/UV = 2V, Not Switching, VSYNC = 0V or LT8606 DFN, VIN ≤ 36V | 3 |
| VIN Current in Regulation | | | 56 | 90 | µA | VIN = 6V, VOUT = 2.7V, Output Load = 100µA | 3 |
| VIN Current in Regulation | | | 500 | 700 | µA | VIN = 6V, VOUT = 2.7V, Output Load = 1mA | 3 |
| Feedback Reference Voltage MSOP Package | | 0.774 | 0.778 | 0.782 | V | VIN = 6V, ILOAD = 100mA | 3 |
| Feedback Reference Voltage MSOP Package | | 0.762 | 0.778 | 0.798 | V | VIN = 6V, ILOAD = 100mA (l, full operating temperature range) | 3 |
| Feedback Voltage Line Regulation | | -0.06 | 0.02 | 0.06 | %/V | VIN = 4.0V to 40V (l) | 3 |
| Feedback Pin Input Current | | -20 | | 20 | nA | VFB = 1V | 3 |
| Minimum On-Time | | | 35 | 65 | ns | ILOAD = 300mA, SYNC = 0V or LT8606 DFN (l) | 3 |
| Minimum On-Time | | | 35 | 60 | ns | ILOAD = 300mA, SYNC = 1.9V or LT8606B DFN (l) | 3 |
| Minimum Off Time | | 93 | | 130 | ns | ILOAD = 300mA (l) | 3 |
| Oscillator Frequency MSOP Package | | 155 | 200 | 245 | kHz | RT = 221k, ILOAD = 250mA (l) | 3 |
| Oscillator Frequency MSOP Package | | 640 | 700 | 760 | kHz | RT = 60.4k, ILOAD = 250mA (l) | 3 |
| Oscillator Frequency MSOP Package | | 1.9 | 2 | 2.1 | MHz | RT = 18.2k, ILOAD = 250mA (l) | 3 |
| Top Power NMOS Current Limit MSOP Package | | 0.65 | 0.9 | 1.15 | A | MSOP Package (l) | 3 |
| Top Power NMOS On-Resistance | | | 375 | | mΩ | ILOAD = 250mA | 3 |
| Bottom Power NMOS On-Resistance | | | 240 | | mΩ | | 3 |
| SW Leakage Current | | | | 5 | µA | VIN = 36V | 3 |
| EN/UV Pin Threshold | | 0.99 | 1.05 | 1.11 | V | EN/UV Rising (l) | 3 |
| EN/UV Pin Hysteresis | | | 50 | | mV | | 3 |
| EN/UV Pin Current | | -20 | | 20 | nA | VEN/UV = 2V | 3 |
| PG Upper Threshold Offset from VFB | | 5 | 8.5 | 13 | % | VFB Rising (l) | 3 |
| PG Lower Threshold Offset from VFB | | 5 | 8.5 | 13 | % | VFB Falling (l) | 3 |
| PG Hysteresis | | | 0.5 | | % | | 3 |
| PG Leakage | | -200 | | 200 | nA | VPG = 42V | 3 |
| PG Pull-Down Resistance | | 550 | | 1200 | Ω | VPG = 0.1V | 3 |
| Sync Low Input Voltage | | 0.4 | | 0.9 | V | MSOP Only (l) | 3 |
| Sync High Input Voltage | | 2.7 | | 3.2 | V | INTVCC = 3.5V, MSOP Only (l) | 3 |
| TR/SS Source Current | | 1 | 2 | 3 | µA | MSOP Only (l) | 3 |
| TR/SS Pull-Down Resistance | | 300 | | 900 | Ω | Fault Condition, TR/SS = 0.1V, MSOP Only | 3 |
| Spread Spectrum Modulation Frequency | | 0.5 | 3 | 6 | kHz | VSYNC = 3.3V, MSOP Only | 3 |
| VIN, EN/UV, PG Absolute Maximum Voltage | | | | 42 | V | | 2 |
| FB, TR/SS Absolute Maximum Voltage | | | | 4 | V | | 2 |
| SYNC Absolute Maximum Voltage | | | | 6 | V | | 2 |
| Operating Junction Temperature Range | | -40 | | 125 | °C | LT8606I | 2 |
| Storage Temperature Range | | -65 | | 150 | °C | | 2 |
| Thermal Resistance Junction-to-Ambient | θJA | | 40 | | °C/W | MSE PACKAGE, 10-LEAD PLASTIC MSOP | 2 |
## CAD (KiCad official)
- Symbol: `LT8606IMSE#TRPBF`
- Footprint: `Package_SO:MSOP-10-1EP_3x3mm_P0.5mm_EP1.68x1.88mm`
- 3D model: MSOP-10-EP (KiCad packages3D, STEP)
- 3D model files: `lt8606imse-trpbf-etched.step` / `lt8606imse-trpbf-etched.glb` carry the MPN laser-etched on the die in a toggleable `Adom.LaserEtch` group (Fusion-ready); `lt8606imse-trpbf.step` / `lt8606imse-trpbf.glb` are the bare package body.
## Provenance
Data extracted from the manufacturer datasheet, not a distributor listing:
- **Datasheet:** [Analog Devices datasheet](https://www.analog.com/media/en/technical-documentation/data-sheets/LT8606-8606B.pdf) (24 pp, sha256 `cfaa3e87d6a68cc5`, retrieved 2026-10-28, tier: manufacturer)
- **Extractor:** parts-factory `2.0.0` / `extract_pins 0.3`, primary `claude-haiku-5-5` (text), consensus `claude-sonnet-5-5` (agreed), guards: pin_guards 0.1: passed. Pins are checked against the footprint pad set and their cited datasheet pages before publish.
- **CAD:** KiCad official libraries (CC-BY-SA 4.0).
[Datasheet PDF](docs/lt8606imse-trpbf-datasheet.pdf)