Loads when you scroll to it. Unloads after 5 minutes in the background.

Symbol & Footprint

Schematic Symbol

Open full view ↗
Loads when you scroll to it. Unloads after 5 minutes in the background.

PCB Footprint

Open full view ↗
Loads when you scroll to it. Unloads after 5 minutes in the background.
Loads when you scroll to it. Unloads after 5 minutes in the background.
Download PDF
Contents

README

markdown

LT8606IMSE#TRPBF

Analog Devices · DC-DC Converters · MSOP-10-EP

LT8606IMSE#TRPBF from Analog Devices, in a MSOP-10-EP. Pinout and pin descriptions extracted from the manufacturer datasheet (extract_pins, cross-checked by a second model); symbol, footprint, and 3D from KiCad-official CAD.

Pinout

Pin Name Type Function
1 BST power_out Provides a drive voltage higher than the input voltage to the topside power switch, so a 0.1µF boost capacitor must be placed as close as possible to the IC with no series resistor.
2 SW output Output of the internal power switches that connects to the inductor and boost capacitor, and this node should be kept small on the PCB for good performance.
3 INTVCC power_out Internal 3.5V regulator bypass pin with maximum output current of 20mA that varies between 2.8V and 3.5V, to be decoupled with at least a 1µF low ESR ceramic capacitor and not loaded externally.
4 RT passive A resistor tied between RT and ground sets the switching frequency, and when synchronizing it must set the frequency at or below the lowest synchronization input.
5 SYNC input External clock synchronization input (MSOP only) that is grounded for Burst Mode operation, left floating for pulse-skipping mode, or tied to a clock or to a voltage between 3.2V and 5.0V for pulse-skipping with spread spectrum.
6 FB input The LT8606 regulates this pin to 0.778V, and the feedback resistor divider tap connects to it.
7 TR/SS passive Output tracking and soft-start pin (MSOP only) with an internal 2µA pull-up from INTVCC, pulled to ground through a 300Ω MOSFET during shutdown and fault conditions, so a series resistor is needed when driven from a low impedance output.
8 PG output Open-drain power good output that remains low until FB is within ±8.5% of the regulation voltage with no fault conditions, and is pulled low when VIN is above 3.2V and EN/UV is low.
9 VIN power_in Supplies current to the internal circuitry and the internal topside power switch, and must be locally bypassed with the input capacitor positive terminal placed as close as possible to the VIN pins.
10 EN/UV input Shuts the LT8606 down when low and enables it when high, with a hysteretic threshold of 1.05V rising and 1.00V falling, and it is tied to VIN if the shutdown feature is not used.
11 GND power_in Exposed pad that must be connected to the negative terminal of the input capacitor and soldered to the PCB to lower the thermal resistance.

Key specifications

Parameter Value
Manufacturer Analog Devices
Package MSOP-10-EP
Category Power Supply Chip
Pins 11

Electrical characteristics

Limits as printed in the datasheet (page.json metadata.characteristics carries them as data).

Parameter Symbol Min Typ Max Unit Conditions Page
Minimum Input Voltage 2.5 3 3.2 V 3
VIN Quiescent Current (shutdown) 1 1.7 µA VEN/UV = 0V 3
VIN Quiescent Current (not switching) 5 12 µA VEN/UV = 2V, Not Switching, VSYNC = 0V or LT8606 DFN, VIN ≤ 36V 3
VIN Current in Regulation 56 90 µA VIN = 6V, VOUT = 2.7V, Output Load = 100µA 3
VIN Current in Regulation 500 700 µA VIN = 6V, VOUT = 2.7V, Output Load = 1mA 3
Feedback Reference Voltage MSOP Package 0.774 0.778 0.782 V VIN = 6V, ILOAD = 100mA 3
Feedback Reference Voltage MSOP Package 0.762 0.778 0.798 V VIN = 6V, ILOAD = 100mA (l, full operating temperature range) 3
Feedback Voltage Line Regulation -0.06 0.02 0.06 %/V VIN = 4.0V to 40V (l) 3
Feedback Pin Input Current -20 20 nA VFB = 1V 3
Minimum On-Time 35 65 ns ILOAD = 300mA, SYNC = 0V or LT8606 DFN (l) 3
Minimum On-Time 35 60 ns ILOAD = 300mA, SYNC = 1.9V or LT8606B DFN (l) 3
Minimum Off Time 93 130 ns ILOAD = 300mA (l) 3
Oscillator Frequency MSOP Package 155 200 245 kHz RT = 221k, ILOAD = 250mA (l) 3
Oscillator Frequency MSOP Package 640 700 760 kHz RT = 60.4k, ILOAD = 250mA (l) 3
Oscillator Frequency MSOP Package 1.9 2 2.1 MHz RT = 18.2k, ILOAD = 250mA (l) 3
Top Power NMOS Current Limit MSOP Package 0.65 0.9 1.15 A MSOP Package (l) 3
Top Power NMOS On-Resistance 375 mΩ ILOAD = 250mA 3
Bottom Power NMOS On-Resistance 240 mΩ 3
SW Leakage Current 5 µA VIN = 36V 3
EN/UV Pin Threshold 0.99 1.05 1.11 V EN/UV Rising (l) 3
EN/UV Pin Hysteresis 50 mV 3
EN/UV Pin Current -20 20 nA VEN/UV = 2V 3
PG Upper Threshold Offset from VFB 5 8.5 13 % VFB Rising (l) 3
PG Lower Threshold Offset from VFB 5 8.5 13 % VFB Falling (l) 3
PG Hysteresis 0.5 % 3
PG Leakage -200 200 nA VPG = 42V 3
PG Pull-Down Resistance 550 1200 Ω VPG = 0.1V 3
Sync Low Input Voltage 0.4 0.9 V MSOP Only (l) 3
Sync High Input Voltage 2.7 3.2 V INTVCC = 3.5V, MSOP Only (l) 3
TR/SS Source Current 1 2 3 µA MSOP Only (l) 3
TR/SS Pull-Down Resistance 300 900 Ω Fault Condition, TR/SS = 0.1V, MSOP Only 3
Spread Spectrum Modulation Frequency 0.5 3 6 kHz VSYNC = 3.3V, MSOP Only 3
VIN, EN/UV, PG Absolute Maximum Voltage 42 V 2
FB, TR/SS Absolute Maximum Voltage 4 V 2
SYNC Absolute Maximum Voltage 6 V 2
Operating Junction Temperature Range -40 125 °C LT8606I 2
Storage Temperature Range -65 150 °C 2
Thermal Resistance Junction-to-Ambient θJA 40 °C/W MSE PACKAGE, 10-LEAD PLASTIC MSOP 2

CAD (KiCad official)

  • Symbol: LT8606IMSE#TRPBF
  • Footprint: Package_SO:MSOP-10-1EP_3x3mm_P0.5mm_EP1.68x1.88mm
  • 3D model: MSOP-10-EP (KiCad packages3D, STEP)
  • 3D model files: lt8606imse-trpbf-etched.step / lt8606imse-trpbf-etched.glb carry the MPN laser-etched on the die in a toggleable Adom.LaserEtch group (Fusion-ready); lt8606imse-trpbf.step / lt8606imse-trpbf.glb are the bare package body.

Provenance

Data extracted from the manufacturer datasheet, not a distributor listing:

  • Datasheet: Analog Devices datasheet (24 pp, sha256 cfaa3e87d6a68cc5, retrieved 2026-10-28, tier: manufacturer)
  • Extractor: parts-factory 2.0.0 / extract_pins 0.3, primary claude-haiku-5-5 (text), consensus claude-sonnet-5-5 (agreed), guards: pin_guards 0.1: passed. Pins are checked against the footprint pad set and their cited datasheet pages before publish.
  • CAD: KiCad official libraries (CC-BY-SA 4.0).

Datasheet PDF