main
Ray
Publish 0.1.0
219491d
LT8390AIUFD#TRPBF
Analog Devices · DC-DC Controllers · QFN-28-EP(4x5)
LT8390AIUFD#TRPBF from Analog Devices, in a QFN-28-EP(4x5). Pinout and pin descriptions extracted from the manufacturer datasheet (extract_pins, cross-checked by a second model); symbol, footprint, and 3D from KiCad-official CAD.
Pinout
| Pin | Name | Type | Function |
|---|---|---|---|
| 1 | TG1 | output | Buck side top gate drive that swings from SW1 to BST1 to drive the buck side top N-channel MOSFET. |
| 2 | LSP | input | Positive terminal of the buck side inductor current sense resistor (RSENSE), which requires a Kelvin connection for accurate current sensing. |
| 3 | LSN | input | Negative terminal of the buck side inductor current sense resistor (RSENSE), which requires a Kelvin connection for accurate current sensing. |
| 4 | VIN | power_in | Input supply pin that sets buck, buck-boost or boost operation over a 4V to 60V range and must be bypassed with a minimum 1µF ceramic capacitor. |
| 5 | INTVCC | power_out | Internal 5V linear regulator output (4.85V to 5.15V at 20mA) supplied from VIN, which must be bypassed with a minimum 4.7µF ceramic capacitor. |
| 6 | EN/UVLO | input | Enable and undervoltage lockout pin that shuts the part down below 0.3V and enables normal operation above 1.233V. |
| 7 | TEST | input | Factory test pin that must be directly connected to ground for the part to operate properly. |
| 8 | LOADEN | input | Load switch enable input with a rising threshold of 1.3V to 1.5V that controls the high side PMOS load switch and must be tied to VREF or INTVCC if unused. |
| 9 | VREF | power_out | Voltage reference output providing an accurate 2V capable of supplying 1mA, which must be bypassed with a 0.47µF ceramic capacitor. |
| 10 | CTRL | input | Control input that programs the ISP/ISN current sense threshold, with 100mV full scale when tied to VREF and switching stopped when forced below 0.3V. |
| 11 | ISP | input | Positive terminal of the ISP/ISN current sense resistor (RIS), which requires a Kelvin connection for accurate current sensing. |
| 12 | ISN | input | Negative terminal of the ISP/ISN current sense resistor (RIS), which requires a Kelvin connection for accurate current sensing. |
| 13 | ISMON | output | Current sense monitor output that generates a voltage equal to ten times V(ISP-ISN) plus a 0.25V offset. |
| 14 | PGOOD | output | Power good open-drain output that is pulled low when FB is within ±10% of the final regulation voltage and requires an external pull-up resistor. |
| 15 | SS | passive | Soft-start timer pin with an internal 12.5µA pull-up, where a 22nF capacitor is recommended and a single resistor to VREF selects the short-circuit fault mode. |
| 16 | FB | input | Voltage loop feedback input that regulates VFB to 1.00V, with output short-circuit below 0.25V and overvoltage above 1.1V. |
| 17 | VC | passive | Error amplifier output that sets the inductor current comparator threshold and is compensated with an external RC network. |
| 18 | RT | passive | Switching frequency setting pin where a resistor from this pin to ground sets the internal oscillator from 600kHz to 2MHz. |
| 19 | SYNC/SPRD | input | Switching frequency synchronization or spread spectrum pin that uses the internal oscillator when grounded, accepts an external clock, or enables 25% triangle spread spectrum when tied to INTVCC. |
| 20 | LOADTG | output | High side PMOS load switch top gate drive, a buffered inverted LOADEN signal that swings from the higher of (VOUT-5V) and 1.2V up to VOUT, and is left unconnected if unused. |
| 21 | VOUT | power_in | Output supply pin that sets buck, buck-boost or boost operation over a 0V to 60V range, serves as the LOADTG rail, and must be bypassed with a minimum 1µF ceramic capacitor. |
| 22 | TG2 | output | Boost side top gate drive that swings from SW2 to BST2 to drive the boost side top N-channel MOSFET. |
| 23 | SW2 | passive | Boost side switch node that swings from a Schottky diode voltage drop below ground up to VOUT. |
| 24 | BST2 | power_out | Boost side bootstrap floating driver supply with an integrated Schottky diode from INTVCC, requiring an external bootstrap capacitor to SW2. |
| 25 | BG2 | output | Boost side bottom gate drive that swings from ground to INTVCC to drive the boost side bottom N-channel MOSFET. |
| 26 | BG1 | output | Buck side bottom gate drive that swings from ground to INTVCC to drive the buck side bottom N-channel MOSFET. |
| 27 | BST1 | power_out | Buck side bootstrap floating driver supply with an integrated Schottky diode from INTVCC, requiring an external bootstrap capacitor to SW1. |
| 28 | SW1 | passive | Buck side switch node that swings from a Schottky diode voltage drop below ground up to VIN. |
| 29 | GND | power_in | Exposed pad ground that must be soldered directly to the ground plane. |
Key specifications
| Parameter | Value |
|---|---|
| Manufacturer | Analog Devices |
| Package | QFN-28-EP(4x5) |
| Category | Power Supply Chip |
| Pins | 29 |
Electrical characteristics
Limits as printed in the datasheet (page.json metadata.characteristics carries them as data).
| Parameter | Symbol | Min | Typ | Max | Unit | Conditions | Page |
|---|---|---|---|---|---|---|---|
| VIN Operating Voltage Range | 4 | 60 | V | 4 | |||
| VOUT Voltage Range | 0 | 60 | V | 4 | |||
| Operating Junction Temperature Range (LT8390AI) | TJ | -40 | 125 | °C | LT8390AI | 2 | |
| VIN, EN/UVLO, VOUT, ISP, ISN voltage | 60 | V | 2 | ||||
| ISP-ISN differential voltage | -1 | 1 | V | 2 | |||
| SW1, SW2, LSP, LSN voltage | -6 | 60 | V | 2 | |||
| INTVCC, (BST1-SW1), (BST2-SW2) voltage | 6 | V | 2 | ||||
| (BST1-LSP), (BST1-LSN) voltage | 6 | V | 2 | ||||
| FB, LOADEN, SYNC/SPRD, CTRL, PGOOD voltage | 6 | V | 2 | ||||
| Storage Temperature Range | -65 | 150 | °C | 2 | |||
| Junction-to-ambient thermal resistance (UFD QFN) | θJA | 43 | °C/W | UFD package | 2 | ||
| Junction-to-case thermal resistance (UFD QFN) | θJC | 3.4 | °C/W | UFD package | 2 | ||
| INTVCC Regulation Voltage | 4.85 | 5 | 5.15 | V | IINTVCC = 20mA | 4 | |
| INTVCC Current Limit | 110 | 145 | 190 | mA | VINTVCC = 4.5V | 4 | |
| INTVCC Undervoltage Lockout Threshold | 3.44 | 3.54 | 3.64 | V | Falling | 4 | |
| VREF Regulation Voltage | 1.97 | 2 | 2.03 | V | IVREF = 100µA | 4 | |
| VREF Current Limit | 2 | 2.5 | 3.2 | mA | VREF = 1.8V | 4 | |
| VREF Undervoltage Lockout Threshold | 1.78 | 1.84 | 1.9 | V | Falling | 4 | |
| EN/UVLO Shutdown Threshold | 0.3 | 0.6 | 1 | V | 4 | ||
| EN/UVLO Enable Threshold | 1.196 | 1.22 | 1.244 | V | Falling | 4 | |
| CTRL Input Bias Current | 0 | 20 | 50 | nA | VCTRL = 0.75V, Current Out of Pin | 4 | |
| CTRL Latch-Off Threshold | 285 | 300 | 315 | mV | Falling | 4 | |
| LOADEN Threshold | 1.3 | 1.4 | 1.5 | V | Rising | 4 | |
| LOADTG On Voltage | V(VOUT-LOADTG) | 4.5 | 5 | 5.5 | V | VOUT = 12V | 4 |
| LOADTG Off Voltage | V(VOUT-LOADTG) | -0.1 | 0 | 0.1 | V | VOUT = 12V | 4 |
| Full Scale Current Regulation | V(ISP-ISN) | 97 | 100 | 103 | mV | VCTRL = 2V, VISP = 12V or 0V | 5 |
| 1/10th Current Regulation | V(ISP-ISN) | 8 | 10 | 12 | mV | VCTRL = 0.35V, VISP = 12V or 0V | 5 |
| ISMON Monitor Output | VISMON | 1.2 | 1.25 | 1.3 | V | V(ISP-ISN) = 100mV, VISP = 12V/0V | 5 |
| ISP/ISN Input Common Mode Range | 0 | 60 | V | 5 | |||
| FB Regulation Voltage | 0.985 | 1 | 1.015 | V | VC = 1.2V | 5 | |
| VC Standby Leakage Current | -10 | 0 | 10 | nA | VC = 1.2V, VLOADEN = 0V | 5 | |
| Maximum Current Sense Threshold (Buck) | V(LSP-LSN) | 35 | 50 | 65 | mV | Buck, VFB = 0.8V | 5 |
| Maximum Current Sense Threshold (Boost) | V(LSP-LSN) | 40 | 50 | 60 | mV | Boost, VFB = 0.8V | 5 |
| FB Overvoltage Threshold (VFB) | VFB | 1.08 | 1.1 | 1.12 | V | Rising | 5 |
| FB Overvoltage Hysteresis | 35 | 50 | 65 | mV | 5 | ||
| FB Short Threshold (VFB) | VFB | 0.24 | 0.25 | 0.26 | V | Falling | 5 |
| PGOOD Upper Threshold | 8 | 10 | 12 | % | Offset from VFB, Rising | 5 | |
| PGOOD Lower Threshold | -12 | -10 | -8 | % | Offset from VFB, Falling | 5 | |
| SS Pull-Up Current | 10 | 12.5 | 15 | µA | VFB = 0.4V, VSS = 0V | 5 | |
| SS Pull-Down Current | 1 | 1.25 | 1.5 | µA | VFB = 0.1V, VSS = 2V | 5 | |
| Switching Frequency | 645 | 685 | 725 | kHz | VSYNC/SPRD = 0V, RT = 226kΩ | 6 | |
| Switching Frequency | 1290 | 1360 | 1430 | kHz | VSYNC/SPRD = 0V, RT = 100kΩ | 6 | |
| Switching Frequency | 1900 | 2000 | 2100 | kHz | VSYNC/SPRD = 0V, RT = 59.0kΩ | 6 | |
| SYNC Frequency | 600 | 2100 | kHz | 6 | |||
| Highest Spread Spectrum Above Oscillator Frequency | 21 | 23 | 25 | % | VSYNC/SPRD = 5V | 6 | |
| Buck-Boost to Boost Region Transition | 0.73 | 0.75 | 0.77 | (VIN/VOUT) | 6 | ||
| Boost to Buck-Boost Region Transition | 0.83 | 0.85 | 0.87 | (VIN/VOUT) | 6 | ||
| Buck to Buck-Boost Region Transition | 1.23 | 1.25 | 1.27 | (VIN/VOUT) | 6 | ||
| Buck-Boost to Buck Region Transition | 1.31 | 1.33 | 1.35 | (VIN/VOUT) | 6 | ||
| Peak-Buck to Peak-Boost Region Transition | 0.96 | 0.98 | 1 | (VIN/VOUT) | 6 | ||
| Peak-Boost to Peak-Buck Region Transition | 1 | 1.02 | 1.04 | (VIN/VOUT) | 6 |
CAD (KiCad official)
- Symbol:
LT8390AIUFD#TRPBF - Footprint:
Package_DFN_QFN:QFN-28-1EP_4x5mm_P0.5mm_EP2.65x3.65mm - 3D model: QFN-28-EP(4x5) (KiCad packages3D, STEP)
- 3D model files:
lt8390aiufd-trpbf-etched.step/lt8390aiufd-trpbf-etched.glbcarry the MPN laser-etched on the die in a toggleableAdom.LaserEtchgroup (Fusion-ready);lt8390aiufd-trpbf.step/lt8390aiufd-trpbf.glbare the bare package body.
Provenance
Data extracted from the manufacturer datasheet, not a distributor listing:
- Datasheet: Analog Devices datasheet (32 pp, sha256
b3c86e61a1228fd3, retrieved 2026-10-28, tier: manufacturer) - Extractor: parts-factory
2.0.0/extract_pins 0.3, primaryclaude-haiku-5-5(text), consensusclaude-sonnet-5-5(agreed), guards: pin_guards 0.1: passed. Pins are checked against the footprint pad set and their cited datasheet pages before publish. - CAD: KiCad official libraries (CC-BY-SA 4.0).
# LT8390AIUFD#TRPBF
**Analog Devices** · DC-DC Controllers · QFN-28-EP(4x5)
LT8390AIUFD#TRPBF from Analog Devices, in a QFN-28-EP(4x5). Pinout and pin descriptions extracted from the manufacturer datasheet (extract_pins, cross-checked by a second model); symbol, footprint, and 3D from KiCad-official CAD.
## Pinout
| Pin | Name | Type | Function |
|---|---|---|---|
| 1 | TG1 | output | Buck side top gate drive that swings from SW1 to BST1 to drive the buck side top N-channel MOSFET. |
| 2 | LSP | input | Positive terminal of the buck side inductor current sense resistor (RSENSE), which requires a Kelvin connection for accurate current sensing. |
| 3 | LSN | input | Negative terminal of the buck side inductor current sense resistor (RSENSE), which requires a Kelvin connection for accurate current sensing. |
| 4 | VIN | power_in | Input supply pin that sets buck, buck-boost or boost operation over a 4V to 60V range and must be bypassed with a minimum 1µF ceramic capacitor. |
| 5 | INTVCC | power_out | Internal 5V linear regulator output (4.85V to 5.15V at 20mA) supplied from VIN, which must be bypassed with a minimum 4.7µF ceramic capacitor. |
| 6 | EN/UVLO | input | Enable and undervoltage lockout pin that shuts the part down below 0.3V and enables normal operation above 1.233V. |
| 7 | TEST | input | Factory test pin that must be directly connected to ground for the part to operate properly. |
| 8 | LOADEN | input | Load switch enable input with a rising threshold of 1.3V to 1.5V that controls the high side PMOS load switch and must be tied to VREF or INTVCC if unused. |
| 9 | VREF | power_out | Voltage reference output providing an accurate 2V capable of supplying 1mA, which must be bypassed with a 0.47µF ceramic capacitor. |
| 10 | CTRL | input | Control input that programs the ISP/ISN current sense threshold, with 100mV full scale when tied to VREF and switching stopped when forced below 0.3V. |
| 11 | ISP | input | Positive terminal of the ISP/ISN current sense resistor (RIS), which requires a Kelvin connection for accurate current sensing. |
| 12 | ISN | input | Negative terminal of the ISP/ISN current sense resistor (RIS), which requires a Kelvin connection for accurate current sensing. |
| 13 | ISMON | output | Current sense monitor output that generates a voltage equal to ten times V(ISP-ISN) plus a 0.25V offset. |
| 14 | PGOOD | output | Power good open-drain output that is pulled low when FB is within ±10% of the final regulation voltage and requires an external pull-up resistor. |
| 15 | SS | passive | Soft-start timer pin with an internal 12.5µA pull-up, where a 22nF capacitor is recommended and a single resistor to VREF selects the short-circuit fault mode. |
| 16 | FB | input | Voltage loop feedback input that regulates VFB to 1.00V, with output short-circuit below 0.25V and overvoltage above 1.1V. |
| 17 | VC | passive | Error amplifier output that sets the inductor current comparator threshold and is compensated with an external RC network. |
| 18 | RT | passive | Switching frequency setting pin where a resistor from this pin to ground sets the internal oscillator from 600kHz to 2MHz. |
| 19 | SYNC/SPRD | input | Switching frequency synchronization or spread spectrum pin that uses the internal oscillator when grounded, accepts an external clock, or enables 25% triangle spread spectrum when tied to INTVCC. |
| 20 | LOADTG | output | High side PMOS load switch top gate drive, a buffered inverted LOADEN signal that swings from the higher of (VOUT-5V) and 1.2V up to VOUT, and is left unconnected if unused. |
| 21 | VOUT | power_in | Output supply pin that sets buck, buck-boost or boost operation over a 0V to 60V range, serves as the LOADTG rail, and must be bypassed with a minimum 1µF ceramic capacitor. |
| 22 | TG2 | output | Boost side top gate drive that swings from SW2 to BST2 to drive the boost side top N-channel MOSFET. |
| 23 | SW2 | passive | Boost side switch node that swings from a Schottky diode voltage drop below ground up to VOUT. |
| 24 | BST2 | power_out | Boost side bootstrap floating driver supply with an integrated Schottky diode from INTVCC, requiring an external bootstrap capacitor to SW2. |
| 25 | BG2 | output | Boost side bottom gate drive that swings from ground to INTVCC to drive the boost side bottom N-channel MOSFET. |
| 26 | BG1 | output | Buck side bottom gate drive that swings from ground to INTVCC to drive the buck side bottom N-channel MOSFET. |
| 27 | BST1 | power_out | Buck side bootstrap floating driver supply with an integrated Schottky diode from INTVCC, requiring an external bootstrap capacitor to SW1. |
| 28 | SW1 | passive | Buck side switch node that swings from a Schottky diode voltage drop below ground up to VIN. |
| 29 | GND | power_in | Exposed pad ground that must be soldered directly to the ground plane. |
## Key specifications
| Parameter | Value |
|---|---|
| Manufacturer | Analog Devices |
| Package | QFN-28-EP(4x5) |
| Category | Power Supply Chip |
| Pins | 29 |
## Electrical characteristics
Limits as printed in the datasheet (page.json `metadata.characteristics` carries them as data).
| Parameter | Symbol | Min | Typ | Max | Unit | Conditions | Page |
|---|---|---|---|---|---|---|---|
| VIN Operating Voltage Range | | 4 | | 60 | V | | 4 |
| VOUT Voltage Range | | 0 | | 60 | V | | 4 |
| Operating Junction Temperature Range (LT8390AI) | TJ | -40 | | 125 | °C | LT8390AI | 2 |
| VIN, EN/UVLO, VOUT, ISP, ISN voltage | | | | 60 | V | | 2 |
| ISP-ISN differential voltage | | -1 | | 1 | V | | 2 |
| SW1, SW2, LSP, LSN voltage | | -6 | | 60 | V | | 2 |
| INTVCC, (BST1-SW1), (BST2-SW2) voltage | | | | 6 | V | | 2 |
| (BST1-LSP), (BST1-LSN) voltage | | | | 6 | V | | 2 |
| FB, LOADEN, SYNC/SPRD, CTRL, PGOOD voltage | | | | 6 | V | | 2 |
| Storage Temperature Range | | -65 | | 150 | °C | | 2 |
| Junction-to-ambient thermal resistance (UFD QFN) | θJA | | 43 | | °C/W | UFD package | 2 |
| Junction-to-case thermal resistance (UFD QFN) | θJC | | 3.4 | | °C/W | UFD package | 2 |
| INTVCC Regulation Voltage | | 4.85 | 5 | 5.15 | V | IINTVCC = 20mA | 4 |
| INTVCC Current Limit | | 110 | 145 | 190 | mA | VINTVCC = 4.5V | 4 |
| INTVCC Undervoltage Lockout Threshold | | 3.44 | 3.54 | 3.64 | V | Falling | 4 |
| VREF Regulation Voltage | | 1.97 | 2 | 2.03 | V | IVREF = 100µA | 4 |
| VREF Current Limit | | 2 | 2.5 | 3.2 | mA | VREF = 1.8V | 4 |
| VREF Undervoltage Lockout Threshold | | 1.78 | 1.84 | 1.9 | V | Falling | 4 |
| EN/UVLO Shutdown Threshold | | 0.3 | 0.6 | 1 | V | | 4 |
| EN/UVLO Enable Threshold | | 1.196 | 1.22 | 1.244 | V | Falling | 4 |
| CTRL Input Bias Current | | 0 | 20 | 50 | nA | VCTRL = 0.75V, Current Out of Pin | 4 |
| CTRL Latch-Off Threshold | | 285 | 300 | 315 | mV | Falling | 4 |
| LOADEN Threshold | | 1.3 | 1.4 | 1.5 | V | Rising | 4 |
| LOADTG On Voltage | V(VOUT-LOADTG) | 4.5 | 5 | 5.5 | V | VOUT = 12V | 4 |
| LOADTG Off Voltage | V(VOUT-LOADTG) | -0.1 | 0 | 0.1 | V | VOUT = 12V | 4 |
| Full Scale Current Regulation | V(ISP-ISN) | 97 | 100 | 103 | mV | VCTRL = 2V, VISP = 12V or 0V | 5 |
| 1/10th Current Regulation | V(ISP-ISN) | 8 | 10 | 12 | mV | VCTRL = 0.35V, VISP = 12V or 0V | 5 |
| ISMON Monitor Output | VISMON | 1.2 | 1.25 | 1.3 | V | V(ISP-ISN) = 100mV, VISP = 12V/0V | 5 |
| ISP/ISN Input Common Mode Range | | 0 | | 60 | V | | 5 |
| FB Regulation Voltage | | 0.985 | 1 | 1.015 | V | VC = 1.2V | 5 |
| VC Standby Leakage Current | | -10 | 0 | 10 | nA | VC = 1.2V, VLOADEN = 0V | 5 |
| Maximum Current Sense Threshold (Buck) | V(LSP-LSN) | 35 | 50 | 65 | mV | Buck, VFB = 0.8V | 5 |
| Maximum Current Sense Threshold (Boost) | V(LSP-LSN) | 40 | 50 | 60 | mV | Boost, VFB = 0.8V | 5 |
| FB Overvoltage Threshold (VFB) | VFB | 1.08 | 1.1 | 1.12 | V | Rising | 5 |
| FB Overvoltage Hysteresis | | 35 | 50 | 65 | mV | | 5 |
| FB Short Threshold (VFB) | VFB | 0.24 | 0.25 | 0.26 | V | Falling | 5 |
| PGOOD Upper Threshold | | 8 | 10 | 12 | % | Offset from VFB, Rising | 5 |
| PGOOD Lower Threshold | | -12 | -10 | -8 | % | Offset from VFB, Falling | 5 |
| SS Pull-Up Current | | 10 | 12.5 | 15 | µA | VFB = 0.4V, VSS = 0V | 5 |
| SS Pull-Down Current | | 1 | 1.25 | 1.5 | µA | VFB = 0.1V, VSS = 2V | 5 |
| Switching Frequency | | 645 | 685 | 725 | kHz | VSYNC/SPRD = 0V, RT = 226kΩ | 6 |
| Switching Frequency | | 1290 | 1360 | 1430 | kHz | VSYNC/SPRD = 0V, RT = 100kΩ | 6 |
| Switching Frequency | | 1900 | 2000 | 2100 | kHz | VSYNC/SPRD = 0V, RT = 59.0kΩ | 6 |
| SYNC Frequency | | 600 | | 2100 | kHz | | 6 |
| Highest Spread Spectrum Above Oscillator Frequency | | 21 | 23 | 25 | % | VSYNC/SPRD = 5V | 6 |
| Buck-Boost to Boost Region Transition | | 0.73 | 0.75 | 0.77 | | (VIN/VOUT) | 6 |
| Boost to Buck-Boost Region Transition | | 0.83 | 0.85 | 0.87 | | (VIN/VOUT) | 6 |
| Buck to Buck-Boost Region Transition | | 1.23 | 1.25 | 1.27 | | (VIN/VOUT) | 6 |
| Buck-Boost to Buck Region Transition | | 1.31 | 1.33 | 1.35 | | (VIN/VOUT) | 6 |
| Peak-Buck to Peak-Boost Region Transition | | 0.96 | 0.98 | 1 | | (VIN/VOUT) | 6 |
| Peak-Boost to Peak-Buck Region Transition | | 1 | 1.02 | 1.04 | | (VIN/VOUT) | 6 |
## CAD (KiCad official)
- Symbol: `LT8390AIUFD#TRPBF`
- Footprint: `Package_DFN_QFN:QFN-28-1EP_4x5mm_P0.5mm_EP2.65x3.65mm`
- 3D model: QFN-28-EP(4x5) (KiCad packages3D, STEP)
- 3D model files: `lt8390aiufd-trpbf-etched.step` / `lt8390aiufd-trpbf-etched.glb` carry the MPN laser-etched on the die in a toggleable `Adom.LaserEtch` group (Fusion-ready); `lt8390aiufd-trpbf.step` / `lt8390aiufd-trpbf.glb` are the bare package body.
## Provenance
Data extracted from the manufacturer datasheet, not a distributor listing:
- **Datasheet:** [Analog Devices datasheet](https://www.analog.com/media/en/technical-documentation/data-sheets/lt8390a.pdf) (32 pp, sha256 `b3c86e61a1228fd3`, retrieved 2026-10-28, tier: manufacturer)
- **Extractor:** parts-factory `2.0.0` / `extract_pins 0.3`, primary `claude-haiku-5-5` (text), consensus `claude-sonnet-5-5` (agreed), guards: pin_guards 0.1: passed. Pins are checked against the footprint pad set and their cited datasheet pages before publish.
- **CAD:** KiCad official libraries (CC-BY-SA 4.0).
[Datasheet PDF](docs/lt8390aiufd-trpbf-datasheet.pdf)