main
Download ZIP Propose a change
Generated by kicad-footprint-generator · KiCad file format 20260206
Name Last commit message Last updated
docs Publish 0.1.0 · Ray
viewers lt8390aeufd-trpbf: viewers · Ray
lt8390aeufd-trpbf-etched.glb Publish 0.1.0 · Ray
lt8390aeufd-trpbf-etched.step lt8390aeufd-trpbf: factory component page (tier=mfr) · Ray
lt8390aeufd-trpbf-hero.glb lt8390aeufd-trpbf: hero GLB from the etched model (keeps the MPN mark) · Ray
lt8390aeufd-trpbf-hero.overlay.json Publish 0.1.0 · Ray
lt8390aeufd-trpbf.glb Publish 0.1.0 · Ray
lt8390aeufd-trpbf.kicad_mod Publish 0.1.0 · Ray
lt8390aeufd-trpbf.kicad_sym Publish 0.1.0 · Ray
lt8390aeufd-trpbf.lbr Publish 0.1.0 · Ray
lt8390aeufd-trpbf.step Publish 0.1.0 · Ray
package.json Publish 0.1.0 · Ray
page.json Set visibility: public · Ray
README.md Publish 0.1.0 · Ray

LT8390AEUFD#TRPBF

Analog Devices · DC-DC Controllers · QFN-28-EP(4x5)

LT8390AEUFD#TRPBF from Analog Devices, in a QFN-28-EP(4x5). Pinout and pin descriptions extracted from the manufacturer datasheet (extract_pins, cross-checked by a second model); symbol, footprint, and 3D from KiCad-official CAD.

Pinout

Pin Name Type Function
1 TG1 output Buck side top gate drive that swings from SW1 to BST1 to drive the buck top N-channel MOSFET.
2 LSP input Positive terminal of the buck side inductor current sense resistor, which requires a Kelvin connection for accurate sensing.
3 LSN input Negative terminal of the buck side inductor current sense resistor, which requires a Kelvin connection for accurate sensing.
4 VIN power_in Input supply with a 4V to 60V operating range that must be locally bypassed to ground with a minimum 1µF ceramic capacitor.
5 INTVCC power_out Internal 5V linear regulator output powered from VIN that must be bypassed to ground with a minimum 4.7µF ceramic capacitor.
6 EN/UVLO input Enable and undervoltage lockout pin that must be forced below 0.3V to shut down and above 1.233V for normal operation.
7 TEST input Factory test pin that must be directly connected to ground for the part to operate properly.
8 LOADEN input Load switch enable input that controls the high side PMOS load switch and must be tied to VREF or INTVCC if unused.
9 VREF power_out Voltage reference output providing an accurate 2V capable of supplying 1mA, requiring a 0.47µF bypass capacitor to ground.
10 CTRL input Control input that sets the ISP/ISN current sense threshold, must not be left open, and must be forced below 0.3V to stop switching.
11 ISP input Positive terminal of the ISP/ISN current sense resistor, which requires a Kelvin connection for accurate sensing.
12 ISN input Negative terminal of the ISP/ISN current sense resistor, which requires a Kelvin connection for accurate sensing.
13 ISMON output Buffered current sense monitor output that equals ten times V(ISP-ISN) plus a 0.25V offset.
14 PGOOD output Open-drain power good output that is pulled low when FB is within ±10% of the regulation voltage and requires an external pull-up resistor.
15 SS passive Soft-start timer pin that sets the ramp with an internal 12.5µA pull-up current and a single resistor to VREF selects the fault mode.
16 FB input Voltage loop feedback input that regulates to 1.00V and triggers overvoltage protection above 1.1V.
17 VC passive Error amplifier output used to compensate the control loop with an external RC network and disconnected from internal loads when LOADEN is low.
18 RT passive Switching frequency setting pin where a resistor to ground sets the internal oscillator from 600kHz to 2MHz.
19 SYNC/SPRD input Synchronization or spread spectrum pin that is grounded for internal oscillator operation, driven by a clock to synchronize, or tied to INTVCC for 25% triangle spread spectrum.
20 LOADTG output High side PMOS load switch top gate drive that swings from the higher of (VOUT-5V) and 1.2V up to VOUT and may be left unconnected if unused.
21 VOUT power_in Output supply with a 0V to 60V voltage range that must be locally bypassed to ground with a minimum 1µF ceramic capacitor.
22 TG2 output Boost side top gate drive that swings from SW2 to BST2 to drive the boost top N-channel MOSFET.
23 SW2 passive Boost side switch node that swings from a Schottky diode voltage drop below ground up to VOUT.
24 BST2 power_out Boost side bootstrap driver supply that swings from a diode drop below INTVCC to (VOUT + INTVCC) and requires an external bootstrap capacitor to SW2.
25 BG2 output Boost side bottom gate drive that swings from ground to INTVCC to drive the boost bottom N-channel MOSFET.
26 BG1 output Buck side bottom gate drive that swings from ground to INTVCC to drive the buck bottom N-channel MOSFET.
27 BST1 power_out Buck side bootstrap driver supply that swings from a diode drop below INTVCC to (VIN + INTVCC) and requires an external bootstrap capacitor to SW1.
28 SW1 passive Buck side switch node that swings from a Schottky diode voltage drop below ground up to VIN.
29 GND power_in Exposed pad ground that must be soldered directly to the PCB ground plane.

Key specifications

Parameter Value
Manufacturer Analog Devices
Package QFN-28-EP(4x5)
Category Power Supply Chip
Pins 29

CAD (KiCad official)

  • Symbol: LT8390AEUFD#TRPBF
  • Footprint: Package_DFN_QFN:QFN-28-1EP_4x5mm_P0.5mm_EP2.65x3.65mm
  • 3D model: QFN-28-EP(4x5) (KiCad packages3D, STEP)
  • 3D model files: lt8390aeufd-trpbf-etched.step / lt8390aeufd-trpbf-etched.glb carry the MPN laser-etched on the die in a toggleable Adom.LaserEtch group (Fusion-ready); lt8390aeufd-trpbf.step / lt8390aeufd-trpbf.glb are the bare package body.

Provenance

Data extracted from the manufacturer datasheet, not a distributor listing:

  • Datasheet: Analog Devices datasheet (32 pp, sha256 b3c86e61a1228fd3, retrieved 2026-10-28, tier: manufacturer)
  • Extractor: parts-factory 2.0.0 / extract_pins 0.3, primary claude-haiku-5-5 (text), consensus claude-sonnet-5-5 (agreed), guards: pin_guards 0.1: passed. Pins are checked against the footprint pad set and their cited datasheet pages before publish.
  • CAD: KiCad official libraries (CC-BY-SA 4.0).

Datasheet PDF