main
Ray
Publish 0.1.0
f12a5cb
123456789101112131415161718192021222324252627282930313233343536373839404142434445464748495051525354555657585960616263646566676869707172737475767778798081828384858687888990919293949596979899100101102103104105106107108109110111112113114115116117118119120121122123124125126127128129130131132133134135136137138139140141142143144145146147148149150151152153154155156157158159160161162163164165166167168169170171172173174175176177178179180181182183184185186187188189190191192193194195196197198199200201202203204205206207208209210
{
"slug": "lt8365emse",
"version": "0.1.0",
"type": "component",
"description": "Analog Devices DC-DC Converters, MSOP-12. Pinout settled in review by an AI reviewer against the manufacturer's datasheet, KiCad symbol/footprint/3D.",
"tags": [
"component",
"power management (pmic)",
"lt8365emse#pbf",
"factory-2.0.0",
"extractor-text"
],
"dependencies": {},
"hero": {
"type": "image",
"path": "docs/hero.png"
},
"files": [
"page.json",
"README.md",
"lt8365emse.kicad_sym",
"lt8365emse.kicad_mod",
"lt8365emse.glb",
"lt8365emse.step",
"lt8365emse.lbr",
"docs/hero.png",
"docs/lt8365emse-datasheet.pdf",
"viewers/symbol.html",
"viewers/footprint.html",
"lt8365emse-hero.glb",
"lt8365emse-hero.overlay.json"
],
"component": {
"mpn": "LT8365EMSE",
"land_source": "datasheet",
"land_note": "ADI LT8365 p.28 MSE Package, Variation MSE16 (12), LTC DWG 05-08-1871 Rev D, RECOMMENDED SOLDER PAD LAYOUT: pads 0.305±0.038 x 0.889±0.127 at 0.50 BSC, rows 5.10 MIN outside and 3.20-3.45 inside, exposed pad 2.845±0.102 x 1.651±0.102, pins 2/4/13/15 absent. KiCad Analog_MSOP-12-16-1EP_3x4.039mm_P0.5mm_EP1.651x2.845mm matches: pads 0.889 x 0.305 at x ±2.1055 (outer span 5.10, inner 3.32), EP 1.651 x 2.845, pads 1,3,5-12,14,16,17.",
"manufacturer": "Analog Devices",
"package": "MSOP-12",
"pin_count": 13,
"category": "Power Management (PMIC)",
"subcategory": "DC-DC Converters",
"datasheet": "https://www.analog.com/media/en/technical-documentation/data-sheets/LT8365.pdf",
"parts": {
"symbol": "lt8365emse.kicad_sym",
"footprint": "lt8365emse.kicad_mod",
"model_3d": "lt8365emse-hero.glb",
"model_3d_plain": "lt8365emse.glb",
"model_3d_step": "lt8365emse-etched.step",
"model_3d_step_plain": "lt8365emse.step",
"lbr": "lt8365emse.lbr"
},
"distributor_links": {
"lcsc": "C673785",
"digikey": "505-LT8365EMSE#PBF-ND",
"mouser": "584-LT8365EMSE#PBF"
},
"distributor_check": {
"checked_at": "2026-11-16T23:47:14Z",
"source": "Component Ocean /api/assign-pns",
"digikey": {
"pn": "505-LT8365EMSE#PBF-ND",
"status": "found"
},
"mouser": {
"pn": "584-LT8365EMSE#PBF",
"status": "found"
}
},
"pins": [
{
"number": "1",
"name": "EN/UVLO",
"type": "input",
"description": "Shutdown and undervoltage detect pin: the part stops switching below the 1.6V threshold, resumes above 1.68V with 80mV hysteresis, and VIN current drops below 1µA when the pin is below 0.2V."
},
{
"number": "3",
"name": "VIN",
"type": "power_in",
"description": "Input supply pin for the 2.8V to 60V operating range, which must be locally bypassed with the input capacitor placed as close as possible to the pin."
},
{
"number": "5",
"name": "INTVCC",
"type": "power_out",
"description": "Regulated 3.8V internal supply that must be bypassed with a 1µF low ESR ceramic capacitor to GND and must not be externally loaded or driven."
},
{
"number": "6",
"name": "NC",
"type": "unconnected",
"description": "No internal connection; leave this pin open."
},
{
"number": "7",
"name": "BIAS",
"type": "input",
"description": "Second input supply for powering INTVCC when 4.4V ≤ BIAS ≤ VIN, which reduces VIN current; tie to GND if unused."
},
{
"number": "8",
"name": "VC",
"type": "output",
"description": "Error amplifier output pin to which the external compensation network is tied."
},
{
"number": "9",
"name": "FBX",
"type": "input",
"description": "Voltage regulation feedback pin for positive or negative outputs, connected through a resistor divider to set the 1.6V (boost/SEPIC) or -0.8V (inverting) regulation level."
},
{
"number": "10",
"name": "RT",
"type": "passive",
"description": "A resistor from this pin to the exposed pad GND programs the switching frequency over the 100kHz to 500kHz range."
},
{
"number": "11",
"name": "SS",
"type": "passive",
"description": "Soft-start pin with a capacitor to GND that controls the inductor current ramp at start-up; charged at 2µA and discharged by an internal 220Ω MOSFET during shutdown or fault."
},
{
"number": "12",
"name": "SYNC/MODE",
"type": "input",
"description": "Selects the operating mode (Burst, pulse-skipping, or SSFM) or synchronizes to an external clock, with GND or <0.14V selecting Burst mode."
},
{
"number": "14",
"name": "SW2",
"type": "output",
"description": "Output of the internal power switch, rated 150V and 1.5A, where the connected metal trace area should be minimized to reduce EMI."
},
{
"number": "16",
"name": "SW1",
"type": "output",
"description": "Output of the internal power switch, rated 150V and 1.5A, where the connected metal trace area should be minimized to reduce EMI."
},
{
"number": "17",
"name": "PGND, GND",
"type": "power_in",
"description": "Exposed pad serving as power and signal ground that must be soldered to a continuous copper ground plane to conduct heat out of the package."
}
],
"provenance": {
"extractor": "ds2sf",
"datasheet": {
"url": "https://www.analog.com/media/en/technical-documentation/data-sheets/LT8365.pdf",
"pages": 30,
"sha256": "c511973eed4b53a9",
"source_tier": "mfr"
},
"cad": "KiCad official (CC-BY-SA 4.0)",
"pins": {
"total": 13,
"described": 13,
"cites_pages": true,
"refuses_to_fabricate": true
}
},
"viewers": {
"symbol": "viewers/symbol.html",
"footprint": "viewers/footprint.html"
},
"models_3d": [
{
"file": "lt8365emse.step",
"role": "plain",
"up": "Z",
"units": "mm",
"origin": "footprint origin = pad-pattern centre",
"seat": "z = 0",
"extents_mm": [
4.9,
4.0,
0.962
],
"zmin_mm": -0.0,
"centre_offset_mm": 0.0,
"footprint_binding": "identity",
"sha256": "eb1612ac73fa5391dcdd85244b8d4a0cbed94d2fe57847a1f5e8e5c1ccf2f82b",
"checked": "2026-11-16",
"checked_by": "factory/step_pose.py (Z-up, origin, seat, binding)"
},
{
"file": "lt8365emse-etched.step",
"role": "eda",
"up": "Z",
"units": "mm",
"origin": "footprint origin = pad-pattern centre",
"seat": "z = 0",
"extents_mm": [
4.9,
4.0,
0.962
],
"zmin_mm": -0.0,
"centre_offset_mm": 0.0,
"footprint_binding": "identity",
"sha256": "d9345c19fc60075a5cc0eece9ec63b0dc0402fd814dcac497bcab19c7f78b1cb",
"checked": "2026-11-16",
"checked_by": "factory/step_pose.py (Z-up, origin, seat, binding)"
}
]
}
}