Generated by kicad-footprint-generator · KiCad file format 20260206
LT8338EMSE#PBF
Analog Devices · DC-DC Converters · MSOP-10-EP
LT8338EMSE#PBF from Analog Devices, in a MSOP-10-EP. Pinout and pin descriptions extracted from the manufacturer datasheet (extract_pins, cross-checked by a second model); symbol, footprint, and 3D from KiCad-official CAD.
Pinout
| Pin | Name | Type | Function |
|---|---|---|---|
| 1 | VIN | power_in | Input supply pin that must be bypassed to GND with a low ESR ceramic capacitor of 0.1µF or greater, placed as close to the pin as possible. |
| 2 | BST | passive | Top switch gate driver supply pin; a 0.1µF capacitor is tied between BST and SW as close as possible to the pins. |
| 3 | SW | output | Switch node connected to the inductor and boost capacitor; it is a high dV/dt node that should be kept compact and away from high impedance nodes. |
| 4 | SW | output | Switch node connected to the inductor and boost capacitor; it is a high dV/dt node that should be kept compact and away from high impedance nodes. |
| 5 | VOUT | power_out | Output voltage pin bypassed to GND with a low ESR ceramic capacitor of 4.7µF or greater; an internal 18:1 resistive divider senses the output for feedback. |
| 6 | SYNC/MODE | input | External synchronization input and light-load mode selection pin, selecting Burst, Burst/SSFM, Pulse-Skipping, Pulse-Skipping/SSFM, or external clock sync modes. |
| 7 | RT | passive | Switching frequency set pin with a resistor to GND that must not be left open; in sync mode the resistor programs the same frequency as the sync signal. |
| 8 | EN/UVLO | input | Enable and input undervoltage lockout pin that shuts the part down below 1V (typ) and enables it above 1.05V (typ), with tying to GND reducing quiescent current to 0.2µA (max). |
| 9 | CTRL | input | Reference input pin that receives the tap of a resistive divider between INTVCC and GND, setting the error amplifier reference to 1/18 of the desired output voltage. |
| 10 | INTVCC | power_out | Internal 2.6V regulator pin that must be bypassed to GND with a low ESR ceramic capacitor of 2.2µF or greater, placed as close to the pin as possible. |
| 11 | GND | power_in | Exposed pad ground pin that must be connected to system ground and soldered to the PCB ground plane for best thermal performance. |
Key specifications
| Parameter | Value |
|---|---|
| Manufacturer | Analog Devices |
| Package | MSOP-10-EP |
| Category | Power Supply Chip |
| Pins | 11 |
Electrical characteristics
Limits as printed in the datasheet (page.json metadata.characteristics carries them as data).
| Parameter | Symbol | Min | Typ | Max | Unit | Conditions | Page |
|---|---|---|---|---|---|---|---|
| VIN, VOUT, EN/UVLO, SW maximum voltage | 40 | V | 2 | ||||
| SYNC/MODE maximum voltage | 6 | V | 2 | ||||
| CTRL Above INTVCC maximum | 0.3 | V | 2 | ||||
| Operating Junction Temperature Range LT8338E | TJ | -40 | 125 | °C | LT8338E grade | 2 | |
| Storage Temperature Range | -65 | 150 | °C | 2 | |||
| VIN Operating Voltage | VIN | 3 | 40 | V | l: over full operating temperature range | 3 | |
| VOUT Regulation VIN=3.3V | VOUT | 8.8 | 9 | 9.2 | V | VIN = 3.3V, CTRL = 0.5V (D = 33.33%); l | 3 |
| VOUT Regulation VIN=9V | VOUT | 17.8 | 18 | 18.2 | V | VIN = 9V, CTRL = 1.0V (D = 50%); l | 3 |
| VOUT Regulation VIN=24V | VOUT | 35.6 | 36 | 36.4 | V | VIN = 24V, CTRL = 2.0V (D = 66.67%); l | 3 |
| VOUT Limit Threshold Voltage | VOUT | 40.2 | 41.4 | V | l | 3 | |
| VOUT IQ in Shutdown | IQ | 5 | µA | EN/UVLO = 0V | 3 | ||
| EN/UVLO Threshold Voltage | 0.975 | 1 | 1.025 | V | EN/UVLO Falling; l | 3 | |
| EN/UVLO Input Bias Current | -40 | 40 | nA | EN/UVLO = 2V | 3 | ||
| INTVCC Regulation Voltage | 2.56 | 2.6 | 2.64 | V | l | 3 | |
| VOUT-to-CTRL Divider Ratio | 17.85 | 18 | 18.15 | V/V | 9V ≤ VOUT ≤ 36V; l | 3 | |
| CTRL Pin Input Current | -20 | 20 | nA | 3 | |||
| Switching Frequency RT=301k | fSW | 270 | 300 | 335 | kHz | RT = 301k; l | 3 |
| Switching Frequency RT=80.6k | fSW | 1.05 | 1.15 | 1.25 | MHz | RT = 80.6k; l | 3 |
| Switching Frequency RT=40.2k | fSW | 2 | 2.2 | 2.4 | MHz | RT = 40.2k; l | 3 |
| SYNC Function Input Frequency Range | 0.3 | 3 | MHz | SYNC/MODE = External Clock | 3 | ||
| Spread Spectrum Frequency Range | 14 | % | Range = (fSW(SPREAD-ON)/fSW(SPREAD-OFF)-1) • 100%; SYNC/MODE = INTVCC | 3 | |||
| SYNC Function Input Low Threshold Voltage | 0.8 | V | SYNC/MODE Pulse Falling | 3 | |||
| SYNC Function Input High Threshold Voltage | 2 | V | SYNC/MODE Pulse Rising | 3 | |||
| SYNC/MODE Pulse Width High | 100 | ns | Synchronization Mode | 4 | |||
| SYNC/MODE Pulse Width Low | 100 | ns | Synchronization Mode | 4 | |||
| Bottom Switch Current Limit | 1.2 | 1.4 | 1.6 | A | l | 4 | |
| Top Switch Current Limit | 1.3 | 1.6 | 1.9 | A | PassThru Mode (Note 7) | 4 | |
| VIN Quiescent Current Shutdown | IQ | 0.1 | 1 | µA | EN/UVLO = 0V (Shutdown Mode) | 3 | |
| VIN Quiescent Current Burst Mode | IQ | 6 | 18 | µA | EN/UVLO = 2V, SYNC/MODE = 0V, Not Switching, VOUT-VIN = +100mV | 3 | |
| VIN Quiescent Current PassThru Mode | IQ | 12 | 35 | µA | EN/UVLO = 2V, SYNC/MODE = 0V, Not Switching, VOUT-VIN < -100mV | 3 | |
| VIN Quiescent Current Pulse-Skipping Mode | IQ | 1200 | 1500 | µA | EN/UVLO = 2V, SYNC/MODE = 2.6V (Pulse-Skipping Mode + SSFM) | 3 | |
| EN/UVLO Rising Hysteresis | 50 | mV | 3 | ||||
| INTVCC Line Regulation | 0.02 | %/V | 3V ≤ VIN ≤ 40V | 3 | |||
| INTVCC Load Regulation | 0.04 | %/mA | 1µA ≤ IINTVCC ≤ 10mA | 3 | |||
| VOUT Internal Divider Resistance | 20 | MΩ | 3 | ||||
| Spread Spectrum Modulation Frequency | 10 | kHz | 3 | ||||
| SYNC/MODE Pin Voltage Floating | 1.3 | V | SYNC/MODE = Floating | 3 | |||
| Bottom Switch Minimum Off-Time | 50 | ns | 4 | ||||
| Bottom Switch Minimum On-Time | 80 | ns | 4 | ||||
| Bottom Switch On-Resistance | 240 | mΩ | 4 | ||||
| Top Switch On-Resistance | 240 | mΩ | 4 | ||||
| Thermal Resistance Junction to Ambient | θJA | 40 | °C/W | 2 |
CAD (KiCad official)
- Symbol:
LT8338EMSE#PBF - Footprint:
Package_SO:MSOP-10-1EP_3x3mm_P0.5mm_EP1.68x1.88mm - 3D model: MSOP-10-EP (KiCad packages3D, STEP)
- 3D model files:
lt8338emse-pbf-etched.step/lt8338emse-pbf-etched.glbcarry the MPN laser-etched on the die in a toggleableAdom.LaserEtchgroup (Fusion-ready);lt8338emse-pbf.step/lt8338emse-pbf.glbare the bare package body.
Provenance
Data extracted from the manufacturer datasheet, not a distributor listing:
- Datasheet: Analog Devices datasheet (21 pp, sha256
e7663816695c683d, retrieved 2026-11-02, tier: manufacturer) - Extractor: parts-factory
2.0.0/extract_pins 0.3, primaryclaude-haiku-5-5(text), consensusclaude-sonnet-5-5(agreed), guards: pin_guards 0.1: passed. Pins are checked against the footprint pad set and their cited datasheet pages before publish. - CAD: KiCad official libraries (CC-BY-SA 4.0).