Loads when you scroll to it. Unloads after 5 minutes in the background.

Symbol & Footprint

Schematic Symbol

Open full view ↗
Loads when you scroll to it. Unloads after 5 minutes in the background.

PCB Footprint

Open full view ↗
Loads when you scroll to it. Unloads after 5 minutes in the background.
Loads when you scroll to it. Unloads after 5 minutes in the background.
Download PDF
Contents

README

markdown

LT8338EMSE#PBF

Analog Devices · DC-DC Converters · MSOP-10-EP

LT8338EMSE#PBF from Analog Devices, in a MSOP-10-EP. Pinout and pin descriptions extracted from the manufacturer datasheet (extract_pins, cross-checked by a second model); symbol, footprint, and 3D from KiCad-official CAD.

Pinout

Pin Name Type Function
1 VIN power_in Input supply pin that must be bypassed to GND with a low ESR ceramic capacitor of 0.1µF or greater, placed as close to the pin as possible.
2 BST passive Top switch gate driver supply pin; a 0.1µF capacitor is tied between BST and SW as close as possible to the pins.
3 SW output Switch node connected to the inductor and boost capacitor; it is a high dV/dt node that should be kept compact and away from high impedance nodes.
4 SW output Switch node connected to the inductor and boost capacitor; it is a high dV/dt node that should be kept compact and away from high impedance nodes.
5 VOUT power_out Output voltage pin bypassed to GND with a low ESR ceramic capacitor of 4.7µF or greater; an internal 18:1 resistive divider senses the output for feedback.
6 SYNC/MODE input External synchronization input and light-load mode selection pin, selecting Burst, Burst/SSFM, Pulse-Skipping, Pulse-Skipping/SSFM, or external clock sync modes.
7 RT passive Switching frequency set pin with a resistor to GND that must not be left open; in sync mode the resistor programs the same frequency as the sync signal.
8 EN/UVLO input Enable and input undervoltage lockout pin that shuts the part down below 1V (typ) and enables it above 1.05V (typ), with tying to GND reducing quiescent current to 0.2µA (max).
9 CTRL input Reference input pin that receives the tap of a resistive divider between INTVCC and GND, setting the error amplifier reference to 1/18 of the desired output voltage.
10 INTVCC power_out Internal 2.6V regulator pin that must be bypassed to GND with a low ESR ceramic capacitor of 2.2µF or greater, placed as close to the pin as possible.
11 GND power_in Exposed pad ground pin that must be connected to system ground and soldered to the PCB ground plane for best thermal performance.

Key specifications

Parameter Value
Manufacturer Analog Devices
Package MSOP-10-EP
Category Power Supply Chip
Pins 11

Electrical characteristics

Limits as printed in the datasheet (page.json metadata.characteristics carries them as data).

Parameter Symbol Min Typ Max Unit Conditions Page
VIN, VOUT, EN/UVLO, SW maximum voltage 40 V 2
SYNC/MODE maximum voltage 6 V 2
CTRL Above INTVCC maximum 0.3 V 2
Operating Junction Temperature Range LT8338E TJ -40 125 °C LT8338E grade 2
Storage Temperature Range -65 150 °C 2
VIN Operating Voltage VIN 3 40 V l: over full operating temperature range 3
VOUT Regulation VIN=3.3V VOUT 8.8 9 9.2 V VIN = 3.3V, CTRL = 0.5V (D = 33.33%); l 3
VOUT Regulation VIN=9V VOUT 17.8 18 18.2 V VIN = 9V, CTRL = 1.0V (D = 50%); l 3
VOUT Regulation VIN=24V VOUT 35.6 36 36.4 V VIN = 24V, CTRL = 2.0V (D = 66.67%); l 3
VOUT Limit Threshold Voltage VOUT 40.2 41.4 V l 3
VOUT IQ in Shutdown IQ 5 µA EN/UVLO = 0V 3
EN/UVLO Threshold Voltage 0.975 1 1.025 V EN/UVLO Falling; l 3
EN/UVLO Input Bias Current -40 40 nA EN/UVLO = 2V 3
INTVCC Regulation Voltage 2.56 2.6 2.64 V l 3
VOUT-to-CTRL Divider Ratio 17.85 18 18.15 V/V 9V ≤ VOUT ≤ 36V; l 3
CTRL Pin Input Current -20 20 nA 3
Switching Frequency RT=301k fSW 270 300 335 kHz RT = 301k; l 3
Switching Frequency RT=80.6k fSW 1.05 1.15 1.25 MHz RT = 80.6k; l 3
Switching Frequency RT=40.2k fSW 2 2.2 2.4 MHz RT = 40.2k; l 3
SYNC Function Input Frequency Range 0.3 3 MHz SYNC/MODE = External Clock 3
Spread Spectrum Frequency Range 14 % Range = (fSW(SPREAD-ON)/fSW(SPREAD-OFF)-1) • 100%; SYNC/MODE = INTVCC 3
SYNC Function Input Low Threshold Voltage 0.8 V SYNC/MODE Pulse Falling 3
SYNC Function Input High Threshold Voltage 2 V SYNC/MODE Pulse Rising 3
SYNC/MODE Pulse Width High 100 ns Synchronization Mode 4
SYNC/MODE Pulse Width Low 100 ns Synchronization Mode 4
Bottom Switch Current Limit 1.2 1.4 1.6 A l 4
Top Switch Current Limit 1.3 1.6 1.9 A PassThru Mode (Note 7) 4
VIN Quiescent Current Shutdown IQ 0.1 1 µA EN/UVLO = 0V (Shutdown Mode) 3
VIN Quiescent Current Burst Mode IQ 6 18 µA EN/UVLO = 2V, SYNC/MODE = 0V, Not Switching, VOUT-VIN = +100mV 3
VIN Quiescent Current PassThru Mode IQ 12 35 µA EN/UVLO = 2V, SYNC/MODE = 0V, Not Switching, VOUT-VIN < -100mV 3
VIN Quiescent Current Pulse-Skipping Mode IQ 1200 1500 µA EN/UVLO = 2V, SYNC/MODE = 2.6V (Pulse-Skipping Mode + SSFM) 3
EN/UVLO Rising Hysteresis 50 mV 3
INTVCC Line Regulation 0.02 %/V 3V ≤ VIN ≤ 40V 3
INTVCC Load Regulation 0.04 %/mA 1µA ≤ IINTVCC ≤ 10mA 3
VOUT Internal Divider Resistance 20 MΩ 3
Spread Spectrum Modulation Frequency 10 kHz 3
SYNC/MODE Pin Voltage Floating 1.3 V SYNC/MODE = Floating 3
Bottom Switch Minimum Off-Time 50 ns 4
Bottom Switch Minimum On-Time 80 ns 4
Bottom Switch On-Resistance 240 mΩ 4
Top Switch On-Resistance 240 mΩ 4
Thermal Resistance Junction to Ambient θJA 40 °C/W 2

CAD (KiCad official)

  • Symbol: LT8338EMSE#PBF
  • Footprint: Package_SO:MSOP-10-1EP_3x3mm_P0.5mm_EP1.68x1.88mm
  • 3D model: MSOP-10-EP (KiCad packages3D, STEP)
  • 3D model files: lt8338emse-pbf-etched.step / lt8338emse-pbf-etched.glb carry the MPN laser-etched on the die in a toggleable Adom.LaserEtch group (Fusion-ready); lt8338emse-pbf.step / lt8338emse-pbf.glb are the bare package body.

Provenance

Data extracted from the manufacturer datasheet, not a distributor listing:

  • Datasheet: Analog Devices datasheet (21 pp, sha256 e7663816695c683d, retrieved 2026-11-02, tier: manufacturer)
  • Extractor: parts-factory 2.0.0 / extract_pins 0.3, primary claude-haiku-5-5 (text), consensus claude-sonnet-5-5 (agreed), guards: pin_guards 0.1: passed. Pins are checked against the footprint pad set and their cited datasheet pages before publish.
  • CAD: KiCad official libraries (CC-BY-SA 4.0).

Datasheet PDF