main
Ray
Publish 0.1.0
274be89
LT3756EUD-2#PBF
Analog Devices · LED Drivers · QFN-16-EP(3x3)
LT3756EUD-2#PBF from Analog Devices, in a QFN-16-EP(3x3). Pinout and pin descriptions extracted from the manufacturer datasheet (extract_pins, cross-checked by a second model); symbol, footprint, and 3D from KiCad-official CAD.
Pinout
| Pin | Name | Type | Function |
|---|---|---|---|
| 1 | VREF | power_in | Voltage reference output, typically 2V, that drives a resistor divider for the CTRL pin and can supply up to 100µA. |
| 2 | PWM | input | A signal low turns off the switcher, idles the oscillator and disconnects VC from internal loads; PWM has an internal pull-down and should be connected to INTVCC if not used. |
| 3 | OPENLED | output | Open-collector pull-down that asserts when FB is greater than the FB regulation threshold minus 50mV (typical), requiring an external pull-up current less than 1mA; on the LT3756-2 this pin is OPENLED, not SYNC. |
| 4 | SS | passive | Soft-start pin with a 10µA (typical) pull-up to an internal 2.5V rail; the soft-start interval is set by an external capacitor and the pin resets to GND on an undervoltage or thermal-limit condition. |
| 5 | RT | passive | Switching frequency adjustment pin set by a resistor to GND (see the Typical Performance curve or Table 1); do not leave open. |
| 6 | SHDN/UVLO | input | Shutdown and undervoltage detect pin with an accurate 1.22V falling threshold; tie to 0.4V or less to disable the device and reduce VIN quiescent current below 1µA. |
| 7 | INTVCC | power_out | Regulated supply for internal loads, GATE driver and PWMOUT driver, regulating to 7.15V (typical); bypass with a 4.7µF capacitor placed close to the pin and connect directly to VIN only if VIN is always ≤ 8V. |
| 8 | VIN | power_in | Input supply pin that must be locally bypassed with a 0.22µF (or larger) capacitor placed close to the IC; VIN absolute maximum is 100V. |
| 9 | SENSE | input | Current sense input for the control loop, Kelvin connected to the positive terminal of the switch current sense resistor in the NFET source, with the negative terminal returned to the GND plane close to the IC. |
| 10 | GATE | output | N-channel FET gate driver output that switches between INTVCC and GND and is driven to GND during shutdown, fault or idle states. |
| 11 | PWMOUT | output | Buffered PWM output driven from INTVCC for an LED load disconnect NMOS or level shift, which also toggles if FB exceeds VFB plus 60mV (typical); a FET with gate cut-off above 1V is recommended. |
| 12 | FB | input | Voltage loop feedback pin that the internal transconductance amplifier regulates to 1.25V (nominal) for constant-voltage regulation or LED protection; do not leave open, connect to GND if not used. |
| 13 | ISN | input | Negative terminal connection of the current feedback resistor; LED current is 100mV/RLED when VCTRL > 1.2V, input bias current is typically 25µA, and below 3V it forces GATE low if ISP exceeds ISN by 150mV (typical). |
| 14 | ISP | input | Positive terminal connection of the current feedback resistor whose input bias current depends on the CTRL voltage, and which acts as a short-circuit protection input when ISN is below 3V. |
| 15 | VC | passive | Transconductance error amplifier output that stabilizes the voltage loop with an RC network, high impedance when PWM is low; connect a capacitor to GND with a series resistor recommended for fast transient response. |
| 16 | CTRL | input | Current sense threshold adjustment pin where V(ISP-ISN) is 1/10 of VCTRL plus an offset for 0V < VCTRL < 1V and constant at 100mV for VCTRL > 1.2V; do not leave open. |
| 17 | GND | power_in | Ground and exposed pad that also serves as the current sense input for the negative terminal of the sense resistor; the exposed pad must be soldered directly to the ground plane. |
Key specifications
| Parameter | Value |
|---|---|
| Manufacturer | Analog Devices |
| Package | QFN-16-EP(3x3) |
| Category | Display Modules / LED Drivers / Display Drivers |
| Pins | 17 |
Electrical characteristics
Limits as printed in the datasheet (page.json metadata.characteristics carries them as data).
| Parameter | Symbol | Min | Typ | Max | Unit | Conditions | Page |
|---|---|---|---|---|---|---|---|
| VIN Shutdown IQ | IQ | 0.1 | 1 | µA | SHDN/UVLO = 0V, PWM = 0V | 4 | |
| VIN Shutdown IQ | IQ | 5 | µA | SHDN/UVLO = 1.15V, PWM = 0V | 4 | ||
| VIN Operating IQ (Not Switching) | IQ | 1.4 | 1.7 | mA | PWM = 0V | 4 | |
| VREF Voltage | VREF | 1.965 | 2 | 2.045 | V | 100µA ≤ IVREF ≤ 0µA (E, I, H-Grades) | 4 |
| SENSE Current Limit Threshold | 98 | 108 | 118 | mV | 4 | ||
| SS Pull-Up Current | 8 | 10 | 13 | µA | Current Out of Pin | 4 | |
| ISP/ISN Full-Scale Current Sense Threshold | 96 | 100 | 103 | mV | FB = 0V, ISP = 48V | 4 | |
| ISP/ISN Current Sense Threshold at CTRL = 0V | -12 | -9.5 | -7 | mV | CTRL = 0V, FB = 0V, ISP = 48V | 4 | |
| CTRL Pin Range for Current Sense Threshold Adjustment | 0 | 1.1 | V | 4 | |||
| CTRL Input Bias Current | 50 | 100 | nA | Current Out of Pin | 4 | ||
| LED Current Sense Amplifier Input Common Mode Range (VISN) | VISN | 2.9 | 100 | V | 4 | ||
| ISP/ISN Short-Circuit Threshold | 115 | 150 | 200 | mV | ISN = 0V | 4 | |
| ISP/ISN Short-Circuit Fault Sensing Common Mode Range (VISN) | VISN | 0 | 3 | V | 4 | ||
| ISP/ISN Input Bias Current (Combined) | 0 | 0.1 | µA | PWM = 0V (Standby), ISP = ISN = 48V | 4 | ||
| VC Standby Input Bias Current | -20 | 20 | nA | PWM = 0V | 4 | ||
| FB Regulation Voltage (VFB) | VFB | 1.22 | 1.25 | 1.27 | V | ISP = ISN (E, I grades) | 4 |
| FB Open LED Threshold (OPENLED Falling, LT3756 and LT3756-2) | -65 | -50 | -40 | mV | Printed as VFB, 65mV / VFB, 50mV / VFB, 40mV | 4 | |
| FB Overvoltage Threshold (PWMOUT Falling) | 50 | 60 | 75 | mV | Printed as VFB + 50mV / VFB + 60mV / VFB + 75mV | 4 | |
| FB Pin Input Bias Current | 40 | 100 | nA | Current Out of Pin | 4 | ||
| Switching Frequency | 90 | 100 | 125 | kHz | RT = 100k | 4 | |
| Switching Frequency | 925 | 1000 | 1050 | kHz | RT = 10k | 4 | |
| INTVCC Regulation Voltage | 7 | 7.15 | 7.3 | V | 4 | ||
| Dropout (VIN, INTVCC) | 1 | V | IINTVCC = -10mA, VIN = 7V | 4 | |||
| INTVCC Undervoltage Lockout | 3.9 | 4.1 | 4.3 | V | 4 | ||
| VIN Minimum Operating Voltage | 6 | V | VIN Tied to INTVCC | 4 | |||
| INTVCC Current Limit | 14 | 17 | 23 | mA | 5 | ||
| INTVCC Current in Shutdown | 8 | 12 | µA | SHDN/UVLO = 0V, INTVCC = 7V | 5 | ||
| PWM Input High Voltage | 1.5 | V | 5 | ||||
| PWM Input Low Voltage | 0.4 | V | 5 | ||||
| PWM Pin Resistance to GND | 45 | 60 | kΩ | 5 | |||
| PWMOUT Output Low (VOL) | VOL | 0 | 50 | mV | 5 | ||
| SHDN/UVLO Threshold Voltage Falling (E-, I-Grades) | 1.185 | 1.22 | 1.245 | V | 5 | ||
| SHDN/UVLO Input Low Voltage | 0.4 | V | IVIN Drops Below 1µA | 5 | |||
| SHDN/UVLO Pin Bias Current Low | 1.7 | 2.05 | 2.5 | µA | SHDN/UVLO = 1.15V | 5 | |
| SHDN/UVLO Pin Bias Current High | 10 | 100 | nA | SHDN/UVLO = 1.30V | 5 | ||
| OPENLED Output Low (VOL) | VOL | 200 | mV | IOPENLED = 0.5mA (LT3756 and LT3756-2) | 5 | ||
| GATE Driver Output Rise Time | tr | 35 | ns | CL = 3300pF | 5 | ||
| GATE Driver Output Fall Time | tf | 35 | ns | CL = 3300pF | 5 | ||
| GATE Output Low (VOL) | VOL | 0.05 | V | 5 | |||
| INTVCC absolute maximum | INTVCC | 8 | V | Printed as VIN + 0.3V, 8V | 2 | ||
| CTRL, PWM, OPENLED absolute maximum | 12 | V | 2 | ||||
| VC, VREF, SS, FB absolute maximum | 3 | V | 2 | ||||
| Operating Junction Temperature Range (E-grade) | TJ | -40 | 125 | °C | LT3756E | 2 | |
| Storage Temperature Range | -65 | 150 | °C | 2 | |||
| VC Output Impedance | 15000 | kΩ | 1V < VC < 2V | 4 | |||
| VREF Line Regulation | 0.006 | %/V | 6V ≤ VIN ≤ 100V | 4 | |||
| SENSE Input Bias Current | 40 | µA | Current Out of Pin | 4 | |||
| ISP/ISN Input Bias Current (Combined) | 55 | µA | PWM = 5V (Active), ISP = ISN = 48V | 4 | |||
| LED Current Sense Amplifier gm | gm | 120 | µS | V(ISP, ISN) = 100mV | 4 | ||
| FB Amplifier gm | gm | 480 | µS | FB = VFB, ISP = ISN | 4 | ||
| VC Current Mode Gain | ∆VVC/∆VSENSE | 4 | V/V | 4 | |||
| Minimum Off-Time | 170 | ns | 4 | ||||
| SHDN/UVLO Rising Hysteresis | 20 | mV | 5 | ||||
| Thermal resistance junction-to-ambient (UD 3x3 QFN) | θJA | 68 | °C/W | UD package (16-lead 3mm × 3mm QFN) | 2 | ||
| Thermal resistance junction-to-case (UD 3x3 QFN) | θJC | 4.2 | °C/W | UD package (16-lead 3mm × 3mm QFN) | 2 |
CAD (KiCad official)
- Symbol:
LT3756EUD-2#PBF - Footprint:
Package_DFN_QFN:QFN-16-1EP_3x3mm_P0.5mm_EP1.7x1.7mm - 3D model: QFN-16-EP(3x3) (KiCad packages3D, STEP)
- 3D model files:
lt3756eud-2-pbf-etched.step/lt3756eud-2-pbf-etched.glbcarry the MPN laser-etched on the die in a toggleableAdom.LaserEtchgroup (Fusion-ready);lt3756eud-2-pbf.step/lt3756eud-2-pbf.glbare the bare package body.
Provenance
Data extracted from the manufacturer datasheet, not a distributor listing:
- Datasheet: Analog Devices datasheet (26 pp, sha256
83d6101210126611, retrieved 2026-10-30, tier: manufacturer) - Extractor: parts-factory
2.0.0/extract_pins 0.3, primaryclaude-haiku-5-5(text), consensusclaude-sonnet-5-5(agreed), guards: pin_guards 0.1: passed. Pins are checked against the footprint pad set and their cited datasheet pages before publish. - CAD: KiCad official libraries (CC-BY-SA 4.0).
# LT3756EUD-2#PBF
**Analog Devices** · LED Drivers · QFN-16-EP(3x3)
LT3756EUD-2#PBF from Analog Devices, in a QFN-16-EP(3x3). Pinout and pin descriptions extracted from the manufacturer datasheet (extract_pins, cross-checked by a second model); symbol, footprint, and 3D from KiCad-official CAD.
## Pinout
| Pin | Name | Type | Function |
|---|---|---|---|
| 1 | VREF | power_in | Voltage reference output, typically 2V, that drives a resistor divider for the CTRL pin and can supply up to 100µA. |
| 2 | PWM | input | A signal low turns off the switcher, idles the oscillator and disconnects VC from internal loads; PWM has an internal pull-down and should be connected to INTVCC if not used. |
| 3 | OPENLED | output | Open-collector pull-down that asserts when FB is greater than the FB regulation threshold minus 50mV (typical), requiring an external pull-up current less than 1mA; on the LT3756-2 this pin is OPENLED, not SYNC. |
| 4 | SS | passive | Soft-start pin with a 10µA (typical) pull-up to an internal 2.5V rail; the soft-start interval is set by an external capacitor and the pin resets to GND on an undervoltage or thermal-limit condition. |
| 5 | RT | passive | Switching frequency adjustment pin set by a resistor to GND (see the Typical Performance curve or Table 1); do not leave open. |
| 6 | SHDN/UVLO | input | Shutdown and undervoltage detect pin with an accurate 1.22V falling threshold; tie to 0.4V or less to disable the device and reduce VIN quiescent current below 1µA. |
| 7 | INTVCC | power_out | Regulated supply for internal loads, GATE driver and PWMOUT driver, regulating to 7.15V (typical); bypass with a 4.7µF capacitor placed close to the pin and connect directly to VIN only if VIN is always ≤ 8V. |
| 8 | VIN | power_in | Input supply pin that must be locally bypassed with a 0.22µF (or larger) capacitor placed close to the IC; VIN absolute maximum is 100V. |
| 9 | SENSE | input | Current sense input for the control loop, Kelvin connected to the positive terminal of the switch current sense resistor in the NFET source, with the negative terminal returned to the GND plane close to the IC. |
| 10 | GATE | output | N-channel FET gate driver output that switches between INTVCC and GND and is driven to GND during shutdown, fault or idle states. |
| 11 | PWMOUT | output | Buffered PWM output driven from INTVCC for an LED load disconnect NMOS or level shift, which also toggles if FB exceeds VFB plus 60mV (typical); a FET with gate cut-off above 1V is recommended. |
| 12 | FB | input | Voltage loop feedback pin that the internal transconductance amplifier regulates to 1.25V (nominal) for constant-voltage regulation or LED protection; do not leave open, connect to GND if not used. |
| 13 | ISN | input | Negative terminal connection of the current feedback resistor; LED current is 100mV/RLED when VCTRL > 1.2V, input bias current is typically 25µA, and below 3V it forces GATE low if ISP exceeds ISN by 150mV (typical). |
| 14 | ISP | input | Positive terminal connection of the current feedback resistor whose input bias current depends on the CTRL voltage, and which acts as a short-circuit protection input when ISN is below 3V. |
| 15 | VC | passive | Transconductance error amplifier output that stabilizes the voltage loop with an RC network, high impedance when PWM is low; connect a capacitor to GND with a series resistor recommended for fast transient response. |
| 16 | CTRL | input | Current sense threshold adjustment pin where V(ISP-ISN) is 1/10 of VCTRL plus an offset for 0V < VCTRL < 1V and constant at 100mV for VCTRL > 1.2V; do not leave open. |
| 17 | GND | power_in | Ground and exposed pad that also serves as the current sense input for the negative terminal of the sense resistor; the exposed pad must be soldered directly to the ground plane. |
## Key specifications
| Parameter | Value |
|---|---|
| Manufacturer | Analog Devices |
| Package | QFN-16-EP(3x3) |
| Category | Display Modules / LED Drivers / Display Drivers |
| Pins | 17 |
## Electrical characteristics
Limits as printed in the datasheet (page.json `metadata.characteristics` carries them as data).
| Parameter | Symbol | Min | Typ | Max | Unit | Conditions | Page |
|---|---|---|---|---|---|---|---|
| VIN Shutdown IQ | IQ | | 0.1 | 1 | µA | SHDN/UVLO = 0V, PWM = 0V | 4 |
| VIN Shutdown IQ | IQ | | | 5 | µA | SHDN/UVLO = 1.15V, PWM = 0V | 4 |
| VIN Operating IQ (Not Switching) | IQ | | 1.4 | 1.7 | mA | PWM = 0V | 4 |
| VREF Voltage | VREF | 1.965 | 2 | 2.045 | V | 100µA ≤ IVREF ≤ 0µA (E, I, H-Grades) | 4 |
| SENSE Current Limit Threshold | | 98 | 108 | 118 | mV | | 4 |
| SS Pull-Up Current | | 8 | 10 | 13 | µA | Current Out of Pin | 4 |
| ISP/ISN Full-Scale Current Sense Threshold | | 96 | 100 | 103 | mV | FB = 0V, ISP = 48V | 4 |
| ISP/ISN Current Sense Threshold at CTRL = 0V | | -12 | -9.5 | -7 | mV | CTRL = 0V, FB = 0V, ISP = 48V | 4 |
| CTRL Pin Range for Current Sense Threshold Adjustment | | 0 | | 1.1 | V | | 4 |
| CTRL Input Bias Current | | | 50 | 100 | nA | Current Out of Pin | 4 |
| LED Current Sense Amplifier Input Common Mode Range (VISN) | VISN | 2.9 | | 100 | V | | 4 |
| ISP/ISN Short-Circuit Threshold | | 115 | 150 | 200 | mV | ISN = 0V | 4 |
| ISP/ISN Short-Circuit Fault Sensing Common Mode Range (VISN) | VISN | 0 | | 3 | V | | 4 |
| ISP/ISN Input Bias Current (Combined) | | | 0 | 0.1 | µA | PWM = 0V (Standby), ISP = ISN = 48V | 4 |
| VC Standby Input Bias Current | | -20 | | 20 | nA | PWM = 0V | 4 |
| FB Regulation Voltage (VFB) | VFB | 1.22 | 1.25 | 1.27 | V | ISP = ISN (E, I grades) | 4 |
| FB Open LED Threshold (OPENLED Falling, LT3756 and LT3756-2) | | -65 | -50 | -40 | mV | Printed as VFB, 65mV / VFB, 50mV / VFB, 40mV | 4 |
| FB Overvoltage Threshold (PWMOUT Falling) | | 50 | 60 | 75 | mV | Printed as VFB + 50mV / VFB + 60mV / VFB + 75mV | 4 |
| FB Pin Input Bias Current | | | 40 | 100 | nA | Current Out of Pin | 4 |
| Switching Frequency | | 90 | 100 | 125 | kHz | RT = 100k | 4 |
| Switching Frequency | | 925 | 1000 | 1050 | kHz | RT = 10k | 4 |
| INTVCC Regulation Voltage | | 7 | 7.15 | 7.3 | V | | 4 |
| Dropout (VIN, INTVCC) | | | | 1 | V | IINTVCC = -10mA, VIN = 7V | 4 |
| INTVCC Undervoltage Lockout | | 3.9 | 4.1 | 4.3 | V | | 4 |
| VIN Minimum Operating Voltage | | | | 6 | V | VIN Tied to INTVCC | 4 |
| INTVCC Current Limit | | 14 | 17 | 23 | mA | | 5 |
| INTVCC Current in Shutdown | | | 8 | 12 | µA | SHDN/UVLO = 0V, INTVCC = 7V | 5 |
| PWM Input High Voltage | | 1.5 | | | V | | 5 |
| PWM Input Low Voltage | | | | 0.4 | V | | 5 |
| PWM Pin Resistance to GND | | 45 | | 60 | kΩ | | 5 |
| PWMOUT Output Low (VOL) | VOL | 0 | | 50 | mV | | 5 |
| SHDN/UVLO Threshold Voltage Falling (E-, I-Grades) | | 1.185 | 1.22 | 1.245 | V | | 5 |
| SHDN/UVLO Input Low Voltage | | | | 0.4 | V | IVIN Drops Below 1µA | 5 |
| SHDN/UVLO Pin Bias Current Low | | 1.7 | 2.05 | 2.5 | µA | SHDN/UVLO = 1.15V | 5 |
| SHDN/UVLO Pin Bias Current High | | | 10 | 100 | nA | SHDN/UVLO = 1.30V | 5 |
| OPENLED Output Low (VOL) | VOL | | | 200 | mV | IOPENLED = 0.5mA (LT3756 and LT3756-2) | 5 |
| GATE Driver Output Rise Time | tr | | | 35 | ns | CL = 3300pF | 5 |
| GATE Driver Output Fall Time | tf | | | 35 | ns | CL = 3300pF | 5 |
| GATE Output Low (VOL) | VOL | | | 0.05 | V | | 5 |
| INTVCC absolute maximum | INTVCC | | | 8 | V | Printed as VIN + 0.3V, 8V | 2 |
| CTRL, PWM, OPENLED absolute maximum | | | | 12 | V | | 2 |
| VC, VREF, SS, FB absolute maximum | | | | 3 | V | | 2 |
| Operating Junction Temperature Range (E-grade) | TJ | -40 | | 125 | °C | LT3756E | 2 |
| Storage Temperature Range | | -65 | | 150 | °C | | 2 |
| VC Output Impedance | | | 15000 | | kΩ | 1V < VC < 2V | 4 |
| VREF Line Regulation | | | 0.006 | | %/V | 6V ≤ VIN ≤ 100V | 4 |
| SENSE Input Bias Current | | | 40 | | µA | Current Out of Pin | 4 |
| ISP/ISN Input Bias Current (Combined) | | | 55 | | µA | PWM = 5V (Active), ISP = ISN = 48V | 4 |
| LED Current Sense Amplifier gm | gm | | 120 | | µS | V(ISP, ISN) = 100mV | 4 |
| FB Amplifier gm | gm | | 480 | | µS | FB = VFB, ISP = ISN | 4 |
| VC Current Mode Gain | ∆VVC/∆VSENSE | | 4 | | V/V | | 4 |
| Minimum Off-Time | | | 170 | | ns | | 4 |
| SHDN/UVLO Rising Hysteresis | | | 20 | | mV | | 5 |
| Thermal resistance junction-to-ambient (UD 3x3 QFN) | θJA | | 68 | | °C/W | UD package (16-lead 3mm × 3mm QFN) | 2 |
| Thermal resistance junction-to-case (UD 3x3 QFN) | θJC | | 4.2 | | °C/W | UD package (16-lead 3mm × 3mm QFN) | 2 |
## CAD (KiCad official)
- Symbol: `LT3756EUD-2#PBF`
- Footprint: `Package_DFN_QFN:QFN-16-1EP_3x3mm_P0.5mm_EP1.7x1.7mm`
- 3D model: QFN-16-EP(3x3) (KiCad packages3D, STEP)
- 3D model files: `lt3756eud-2-pbf-etched.step` / `lt3756eud-2-pbf-etched.glb` carry the MPN laser-etched on the die in a toggleable `Adom.LaserEtch` group (Fusion-ready); `lt3756eud-2-pbf.step` / `lt3756eud-2-pbf.glb` are the bare package body.
## Provenance
Data extracted from the manufacturer datasheet, not a distributor listing:
- **Datasheet:** [Analog Devices datasheet](https://www.analog.com/media/en/technical-documentation/data-sheets/LT3756-3756-1-3756-2.pdf) (26 pp, sha256 `83d6101210126611`, retrieved 2026-10-30, tier: manufacturer)
- **Extractor:** parts-factory `2.0.0` / `extract_pins 0.3`, primary `claude-haiku-5-5` (text), consensus `claude-sonnet-5-5` (agreed), guards: pin_guards 0.1: passed. Pins are checked against the footprint pad set and their cited datasheet pages before publish.
- **CAD:** KiCad official libraries (CC-BY-SA 4.0).
[Datasheet PDF](docs/lt3756eud-2-pbf-datasheet.pdf)