main
Download ZIP Propose a change
Generated by kicad-footprint-generator · KiCad file format 20260206
Name Last commit message Last updated
docs Publish 0.1.0 · Ray
viewers lt3756eud-2-pbf: viewers · Ray
lt3756eud-2-pbf-etched.glb Publish 0.1.0 · Ray
lt3756eud-2-pbf-etched.step lt3756eud-2-pbf: factory component page (tier=mfr) · Ray
lt3756eud-2-pbf-hero.glb lt3756eud-2-pbf: hero GLB from the etched model (keeps the MPN mark) · Ray
lt3756eud-2-pbf-hero.overlay.json Publish 0.1.0 · Ray
lt3756eud-2-pbf.glb Publish 0.1.0 · Ray
lt3756eud-2-pbf.kicad_mod Publish 0.1.0 · Ray
lt3756eud-2-pbf.kicad_sym Publish 0.1.0 · Ray
lt3756eud-2-pbf.lbr Publish 0.1.0 · Ray
lt3756eud-2-pbf.step Publish 0.1.0 · Ray
package.json Publish 0.1.1 · Ray
page.json Publish 0.1.1 · Ray
README.md Publish 0.1.0 · Ray
verification.json Verified: Published by the parts factory: tier mfr, 17 pins · Ray

LT3756EUD-2#PBF

Analog Devices · LED Drivers · QFN-16-EP(3x3)

LT3756EUD-2#PBF from Analog Devices, in a QFN-16-EP(3x3). Pinout and pin descriptions extracted from the manufacturer datasheet (extract_pins, cross-checked by a second model); symbol, footprint, and 3D from KiCad-official CAD.

Pinout

Pin Name Type Function
1 VREF power_in Voltage reference output, typically 2V, that drives a resistor divider for the CTRL pin and can supply up to 100µA.
2 PWM input A signal low turns off the switcher, idles the oscillator and disconnects VC from internal loads; PWM has an internal pull-down and should be connected to INTVCC if not used.
3 OPENLED output Open-collector pull-down that asserts when FB is greater than the FB regulation threshold minus 50mV (typical), requiring an external pull-up current less than 1mA; on the LT3756-2 this pin is OPENLED, not SYNC.
4 SS passive Soft-start pin with a 10µA (typical) pull-up to an internal 2.5V rail; the soft-start interval is set by an external capacitor and the pin resets to GND on an undervoltage or thermal-limit condition.
5 RT passive Switching frequency adjustment pin set by a resistor to GND (see the Typical Performance curve or Table 1); do not leave open.
6 SHDN/UVLO input Shutdown and undervoltage detect pin with an accurate 1.22V falling threshold; tie to 0.4V or less to disable the device and reduce VIN quiescent current below 1µA.
7 INTVCC power_out Regulated supply for internal loads, GATE driver and PWMOUT driver, regulating to 7.15V (typical); bypass with a 4.7µF capacitor placed close to the pin and connect directly to VIN only if VIN is always ≤ 8V.
8 VIN power_in Input supply pin that must be locally bypassed with a 0.22µF (or larger) capacitor placed close to the IC; VIN absolute maximum is 100V.
9 SENSE input Current sense input for the control loop, Kelvin connected to the positive terminal of the switch current sense resistor in the NFET source, with the negative terminal returned to the GND plane close to the IC.
10 GATE output N-channel FET gate driver output that switches between INTVCC and GND and is driven to GND during shutdown, fault or idle states.
11 PWMOUT output Buffered PWM output driven from INTVCC for an LED load disconnect NMOS or level shift, which also toggles if FB exceeds VFB plus 60mV (typical); a FET with gate cut-off above 1V is recommended.
12 FB input Voltage loop feedback pin that the internal transconductance amplifier regulates to 1.25V (nominal) for constant-voltage regulation or LED protection; do not leave open, connect to GND if not used.
13 ISN input Negative terminal connection of the current feedback resistor; LED current is 100mV/RLED when VCTRL > 1.2V, input bias current is typically 25µA, and below 3V it forces GATE low if ISP exceeds ISN by 150mV (typical).
14 ISP input Positive terminal connection of the current feedback resistor whose input bias current depends on the CTRL voltage, and which acts as a short-circuit protection input when ISN is below 3V.
15 VC passive Transconductance error amplifier output that stabilizes the voltage loop with an RC network, high impedance when PWM is low; connect a capacitor to GND with a series resistor recommended for fast transient response.
16 CTRL input Current sense threshold adjustment pin where V(ISP-ISN) is 1/10 of VCTRL plus an offset for 0V < VCTRL < 1V and constant at 100mV for VCTRL > 1.2V; do not leave open.
17 GND power_in Ground and exposed pad that also serves as the current sense input for the negative terminal of the sense resistor; the exposed pad must be soldered directly to the ground plane.

Key specifications

Parameter Value
Manufacturer Analog Devices
Package QFN-16-EP(3x3)
Category Display Modules / LED Drivers / Display Drivers
Pins 17

Electrical characteristics

Limits as printed in the datasheet (page.json metadata.characteristics carries them as data).

Parameter Symbol Min Typ Max Unit Conditions Page
VIN Shutdown IQ IQ 0.1 1 µA SHDN/UVLO = 0V, PWM = 0V 4
VIN Shutdown IQ IQ 5 µA SHDN/UVLO = 1.15V, PWM = 0V 4
VIN Operating IQ (Not Switching) IQ 1.4 1.7 mA PWM = 0V 4
VREF Voltage VREF 1.965 2 2.045 V 100µA ≤ IVREF ≤ 0µA (E, I, H-Grades) 4
SENSE Current Limit Threshold 98 108 118 mV 4
SS Pull-Up Current 8 10 13 µA Current Out of Pin 4
ISP/ISN Full-Scale Current Sense Threshold 96 100 103 mV FB = 0V, ISP = 48V 4
ISP/ISN Current Sense Threshold at CTRL = 0V -12 -9.5 -7 mV CTRL = 0V, FB = 0V, ISP = 48V 4
CTRL Pin Range for Current Sense Threshold Adjustment 0 1.1 V 4
CTRL Input Bias Current 50 100 nA Current Out of Pin 4
LED Current Sense Amplifier Input Common Mode Range (VISN) VISN 2.9 100 V 4
ISP/ISN Short-Circuit Threshold 115 150 200 mV ISN = 0V 4
ISP/ISN Short-Circuit Fault Sensing Common Mode Range (VISN) VISN 0 3 V 4
ISP/ISN Input Bias Current (Combined) 0 0.1 µA PWM = 0V (Standby), ISP = ISN = 48V 4
VC Standby Input Bias Current -20 20 nA PWM = 0V 4
FB Regulation Voltage (VFB) VFB 1.22 1.25 1.27 V ISP = ISN (E, I grades) 4
FB Open LED Threshold (OPENLED Falling, LT3756 and LT3756-2) -65 -50 -40 mV Printed as VFB, 65mV / VFB, 50mV / VFB, 40mV 4
FB Overvoltage Threshold (PWMOUT Falling) 50 60 75 mV Printed as VFB + 50mV / VFB + 60mV / VFB + 75mV 4
FB Pin Input Bias Current 40 100 nA Current Out of Pin 4
Switching Frequency 90 100 125 kHz RT = 100k 4
Switching Frequency 925 1000 1050 kHz RT = 10k 4
INTVCC Regulation Voltage 7 7.15 7.3 V 4
Dropout (VIN, INTVCC) 1 V IINTVCC = -10mA, VIN = 7V 4
INTVCC Undervoltage Lockout 3.9 4.1 4.3 V 4
VIN Minimum Operating Voltage 6 V VIN Tied to INTVCC 4
INTVCC Current Limit 14 17 23 mA 5
INTVCC Current in Shutdown 8 12 µA SHDN/UVLO = 0V, INTVCC = 7V 5
PWM Input High Voltage 1.5 V 5
PWM Input Low Voltage 0.4 V 5
PWM Pin Resistance to GND 45 60 kΩ 5
PWMOUT Output Low (VOL) VOL 0 50 mV 5
SHDN/UVLO Threshold Voltage Falling (E-, I-Grades) 1.185 1.22 1.245 V 5
SHDN/UVLO Input Low Voltage 0.4 V IVIN Drops Below 1µA 5
SHDN/UVLO Pin Bias Current Low 1.7 2.05 2.5 µA SHDN/UVLO = 1.15V 5
SHDN/UVLO Pin Bias Current High 10 100 nA SHDN/UVLO = 1.30V 5
OPENLED Output Low (VOL) VOL 200 mV IOPENLED = 0.5mA (LT3756 and LT3756-2) 5
GATE Driver Output Rise Time tr 35 ns CL = 3300pF 5
GATE Driver Output Fall Time tf 35 ns CL = 3300pF 5
GATE Output Low (VOL) VOL 0.05 V 5
INTVCC absolute maximum INTVCC 8 V Printed as VIN + 0.3V, 8V 2
CTRL, PWM, OPENLED absolute maximum 12 V 2
VC, VREF, SS, FB absolute maximum 3 V 2
Operating Junction Temperature Range (E-grade) TJ -40 125 °C LT3756E 2
Storage Temperature Range -65 150 °C 2
VC Output Impedance 15000 kΩ 1V < VC < 2V 4
VREF Line Regulation 0.006 %/V 6V ≤ VIN ≤ 100V 4
SENSE Input Bias Current 40 µA Current Out of Pin 4
ISP/ISN Input Bias Current (Combined) 55 µA PWM = 5V (Active), ISP = ISN = 48V 4
LED Current Sense Amplifier gm gm 120 µS V(ISP, ISN) = 100mV 4
FB Amplifier gm gm 480 µS FB = VFB, ISP = ISN 4
VC Current Mode Gain ∆VVC/∆VSENSE 4 V/V 4
Minimum Off-Time 170 ns 4
SHDN/UVLO Rising Hysteresis 20 mV 5
Thermal resistance junction-to-ambient (UD 3x3 QFN) θJA 68 °C/W UD package (16-lead 3mm × 3mm QFN) 2
Thermal resistance junction-to-case (UD 3x3 QFN) θJC 4.2 °C/W UD package (16-lead 3mm × 3mm QFN) 2

CAD (KiCad official)

  • Symbol: LT3756EUD-2#PBF
  • Footprint: Package_DFN_QFN:QFN-16-1EP_3x3mm_P0.5mm_EP1.7x1.7mm
  • 3D model: QFN-16-EP(3x3) (KiCad packages3D, STEP)
  • 3D model files: lt3756eud-2-pbf-etched.step / lt3756eud-2-pbf-etched.glb carry the MPN laser-etched on the die in a toggleable Adom.LaserEtch group (Fusion-ready); lt3756eud-2-pbf.step / lt3756eud-2-pbf.glb are the bare package body.

Provenance

Data extracted from the manufacturer datasheet, not a distributor listing:

  • Datasheet: Analog Devices datasheet (26 pp, sha256 83d6101210126611, retrieved 2026-10-30, tier: manufacturer)
  • Extractor: parts-factory 2.0.0 / extract_pins 0.3, primary claude-haiku-5-5 (text), consensus claude-sonnet-5-5 (agreed), guards: pin_guards 0.1: passed. Pins are checked against the footprint pad set and their cited datasheet pages before publish.
  • CAD: KiCad official libraries (CC-BY-SA 4.0).

Datasheet PDF