main
Ray
Publish 0.1.0
11f8d29
LT3743EUFD#PBF
Analog Devices · LED Drivers · QFN-28-EP(4x5)
LT3743EUFD#PBF from Analog Devices, in a QFN-28-EP(4x5). Pinout and pin descriptions extracted from the manufacturer datasheet (extract_pins, cross-checked by a second model); symbol, footprint, and 3D from KiCad-official CAD.
Pinout
| Pin | Name | Type | Function |
|---|---|---|---|
| 1 | GND | power_in | Ground pin; the exposed pad must be soldered to the PCB. |
| 2 | EN/UVLO | input | Enable pin that turns on the internal bias core and subregulators at 1.55V, has no pull-up or pull-down, and full shutdown occurs at approximately 0.5V. |
| 3 | VREF | power_out | Buffered 2V reference capable of 0.5mA drive. |
| 4 | CTRL_T | input | Thermal control input that reduces the regulated current level for both CTRL_L and CTRL_H levels. |
| 5 | GND | power_in | Ground pin; the exposed pad must be soldered to the PCB. |
| 6 | CTRL_H | input | Sets the high level regulated output current and overcurrent set point, with the input internally clamped to a maximum of 1.5V. |
| 7 | CTRL_L | input | Sets the low level regulated output current, and should not be higher than the CTRL_H voltage. |
| 8 | SS | passive | Soft-start pin with an external capacitor to ground that limits regulated current during start-up, with a 5.5µA charging current. |
| 9 | GND | power_in | Ground pin; the exposed pad must be soldered to the PCB. |
| 10 | FB | input | Feedback pin for overvoltage protection with a feedback voltage of 1V, where exceeding 1.3V triggers the overvoltage lockout. |
| 11 | SENSE+ | input | Inverting input of the average current mode loop error amplifier, connected to the external current sense resistor RS. |
| 12 | SENSE- | input | Noninverting input of the average current mode loop error amplifier, through which the reference current flows out of the pin to the LED side of the sense resistor RS. |
| 13 | VCL | passive | Provides average current loop compensation for low level current regulation, with typical values of 15k to 80k for the resistor and 2nF to 10nF for the capacitor. |
| 14 | VCH | passive | Provides average current loop compensation for high level current regulation, with typical values of 15k to 80k for the resistor and 2nF to 10nF for the capacitor. |
| 15 | RT | passive | A resistor to ground sets the switching frequency between 200kHz and 1MHz, is current limited to 60µA, and must not be left open. |
| 16 | SYNC | input | Frequency synchronization pin with a synchronization range of 240kHz to 1.2MHz, which should be grounded when not in use. |
| 17 | CTRL_SEL | input | Selects between high current control CTRL_H and low current control CTRL_L for current level dimming, and should be grounded when not in use. |
| 18 | PWM | input | Input pin for PWM dimming of the LED where low terminates all switching and disconnects the output caps, and it should be pulled to VCC_INT when not in use. |
| 19 | PWMGH | output | Drives the gate of an external FET to connect a switching regulator output capacitor to the load, with pull-up impedance of 3.2Ω and pull-down impedance of 1.75Ω. |
| 20 | GND | power_in | Ground pin; the exposed pad must be soldered to the PCB. |
| 21 | GND | power_in | Ground pin; the exposed pad must be soldered to the PCB. |
| 22 | PWMGL | output | Drives the gate of an external FET to connect a switching regulator output capacitor to the load, with pull-up impedance of 3.2Ω and pull-down impedance of 1.75Ω. |
| 23 | HG | output | Top FET gate drive signal controlling the high side external power FET, with pull-up impedance of 2.3Ω and pull-down impedance of 1.3Ω. |
| 24 | SW | passive | Lower rail for the floating high side driver that connects the two power FETs and the inductor externally. |
| 25 | CBOOT | power_out | Provides a floating 5V regulated supply for the high side FET driver, requiring an external Schottky diode from VCC_INT. |
| 26 | LG | output | Bottom FET gate drive signal controlling the low side external power FET, with pull-up impedance of 2.5Ω and pull-down impedance of 1.3Ω. |
| 27 | VCC_INT | power_out | Regulated 5V output for charging the CBOOT capacitor and powering digital and switching subcircuits, current limited to approximately 50mA. |
| 28 | VIN | power_in | Input supply pin that must be locally bypassed with a 1µF low ESR capacitor to ground, with an input voltage range of 6V to 36V. |
| 29 | GND | power_in | Exposed thermal pad connected to ground that must be soldered to the PCB. |
Key specifications
| Parameter | Value |
|---|---|
| Manufacturer | Analog Devices |
| Package | QFN-28-EP(4x5) |
| Category | Display Modules / LED Drivers / Display Drivers |
| Pins | 29 |
Electrical characteristics
Limits as printed in the datasheet (page.json metadata.characteristics carries them as data).
| Parameter | Symbol | Min | Typ | Max | Unit | Conditions | Page |
|---|---|---|---|---|---|---|---|
| Input Voltage Range | 6 | 36 | V | 3 | |||
| Feedback Regulation Voltage | 0.945 | 1 | 1.025 | V | VCTRL_H = 0V, VCTRL_L = 2V, VSENSE+ = 2V | 3 | |
| Reference Voltage (VREF Pin) | 1.96 | 2 | 2.04 | V | 3 | ||
| Full Range SENSE+ to SENSE- | 48 | 51 | 54 | mV | VCTRL_H = 1.5V, VSENSE- = 6V | 3 | |
| Regulation Voltage (VCC_INT Pin) | 4.7 | 5 | 5.2 | V | 3 | ||
| Switching Frequency | fSW | 900 | 1000 | 1070 | kHz | RT = 40kΩ | 3 |
| Switching Frequency | fSW | 190 | 200 | 233 | kHz | RT = 200kΩ | 3 |
| VIN Pin Quiescent Current, Non-Switching Operation | 1.8 | 2.5 | mA | VPWM = VCTRL_SEL = 0V, Not Switching, RT = 40k | 3 | ||
| VIN Pin Quiescent Current, Shutdown Mode | 0.1 | 1 | µA | VEN/UVLO = 0V | 3 | ||
| EN/UVLO Pin Falling Threshold | 1.49 | 1.55 | 1.61 | V | 3 | ||
| CTRL_H and CTRL_L Pin Control Range | 0 | 1.5 | V | 3 | |||
| Current Control Loop gm Amp Offset Voltage | -3 | 0 | 3 | mV | VSENSE+ = 4V, VSENSE- = 4V | 4 | |
| Current Control Loop gm | gm | 375 | 475 | 625 | µA/V | 4 | |
| CTRL_SEL High to PWMGL Low Delay | 10 | 40 | ns | 4 | |||
| CTRL_SEL High to PWMGH High Delay | 150 | 200 | ns | 4 | |||
| CTRL_SEL Low to PWMGH Low Delay | 30 | 60 | ns | 4 | |||
| CTRL_SEL Low to PWMGL High Delay | 170 | 220 | ns | 4 | |||
| Operating Temperature Range | -40 | 125 | °C | Per ordering table for LT3743EUFD#PBF | 2 | ||
| VIN Voltage | 40 | V | 2 | ||||
| EN/UVLO Voltage | 6 | V | 2 | ||||
| VREF Voltage | 3 | V | 2 | ||||
| CTRL_L, CTRL_H, CTRL_T Voltage | 3 | V | 2 | ||||
| PWM, CTRL_SEL Voltage | 6 | V | 2 | ||||
| SENSE+ Voltage | 40 | V | 2 | ||||
| SENSE- Voltage | 40 | V | 2 | ||||
| VCH, VCL Voltage | 3 | V | 2 | ||||
| SW Voltage | 40 | V | 2 | ||||
| RT Voltage | 3 | V | 2 | ||||
| FB Voltage | 3 | V | 2 | ||||
| SS Voltage | 6 | V | 2 | ||||
| SYNC Voltage | 6 | V | 2 | ||||
| Storage Temperature Range | -65 | 150 | °C | 2 | |||
| Thermal Resistance Junction to Ambient (QFN) | θJA | 37 | °C/W | 28-lead 4mm×5mm QFN (UFD package) | 2 | ||
| Maximum Junction Temperature (QFN) | TJMAX | 125 | °C | 28-lead 4mm×5mm QFN (UFD package) | 2 |
CAD (KiCad official)
- Symbol:
LT3743EUFD#PBF - Footprint:
Package_DFN_QFN:QFN-28-1EP_4x5mm_P0.5mm_EP2.65x3.65mm - 3D model: QFN-28-EP(4x5) (KiCad packages3D, STEP)
- 3D model files:
lt3743eufd-pbf-etched.step/lt3743eufd-pbf-etched.glbcarry the MPN laser-etched on the die in a toggleableAdom.LaserEtchgroup (Fusion-ready);lt3743eufd-pbf.step/lt3743eufd-pbf.glbare the bare package body.
Provenance
Data extracted from the manufacturer datasheet, not a distributor listing:
- Datasheet: Analog Devices datasheet (28 pp, sha256
422657c9cc941519, retrieved 2026-11-02, tier: manufacturer) - Extractor: parts-factory
2.0.0/extract_pins 0.3, primaryclaude-haiku-5-5(text), consensusclaude-sonnet-5-5(agreed), guards: pin_guards 0.1: passed. Pins are checked against the footprint pad set and their cited datasheet pages before publish. - CAD: KiCad official libraries (CC-BY-SA 4.0).
# LT3743EUFD#PBF
**Analog Devices** · LED Drivers · QFN-28-EP(4x5)
LT3743EUFD#PBF from Analog Devices, in a QFN-28-EP(4x5). Pinout and pin descriptions extracted from the manufacturer datasheet (extract_pins, cross-checked by a second model); symbol, footprint, and 3D from KiCad-official CAD.
## Pinout
| Pin | Name | Type | Function |
|---|---|---|---|
| 1 | GND | power_in | Ground pin; the exposed pad must be soldered to the PCB. |
| 2 | EN/UVLO | input | Enable pin that turns on the internal bias core and subregulators at 1.55V, has no pull-up or pull-down, and full shutdown occurs at approximately 0.5V. |
| 3 | VREF | power_out | Buffered 2V reference capable of 0.5mA drive. |
| 4 | CTRL_T | input | Thermal control input that reduces the regulated current level for both CTRL_L and CTRL_H levels. |
| 5 | GND | power_in | Ground pin; the exposed pad must be soldered to the PCB. |
| 6 | CTRL_H | input | Sets the high level regulated output current and overcurrent set point, with the input internally clamped to a maximum of 1.5V. |
| 7 | CTRL_L | input | Sets the low level regulated output current, and should not be higher than the CTRL_H voltage. |
| 8 | SS | passive | Soft-start pin with an external capacitor to ground that limits regulated current during start-up, with a 5.5µA charging current. |
| 9 | GND | power_in | Ground pin; the exposed pad must be soldered to the PCB. |
| 10 | FB | input | Feedback pin for overvoltage protection with a feedback voltage of 1V, where exceeding 1.3V triggers the overvoltage lockout. |
| 11 | SENSE+ | input | Inverting input of the average current mode loop error amplifier, connected to the external current sense resistor RS. |
| 12 | SENSE- | input | Noninverting input of the average current mode loop error amplifier, through which the reference current flows out of the pin to the LED side of the sense resistor RS. |
| 13 | VCL | passive | Provides average current loop compensation for low level current regulation, with typical values of 15k to 80k for the resistor and 2nF to 10nF for the capacitor. |
| 14 | VCH | passive | Provides average current loop compensation for high level current regulation, with typical values of 15k to 80k for the resistor and 2nF to 10nF for the capacitor. |
| 15 | RT | passive | A resistor to ground sets the switching frequency between 200kHz and 1MHz, is current limited to 60µA, and must not be left open. |
| 16 | SYNC | input | Frequency synchronization pin with a synchronization range of 240kHz to 1.2MHz, which should be grounded when not in use. |
| 17 | CTRL_SEL | input | Selects between high current control CTRL_H and low current control CTRL_L for current level dimming, and should be grounded when not in use. |
| 18 | PWM | input | Input pin for PWM dimming of the LED where low terminates all switching and disconnects the output caps, and it should be pulled to VCC_INT when not in use. |
| 19 | PWMGH | output | Drives the gate of an external FET to connect a switching regulator output capacitor to the load, with pull-up impedance of 3.2Ω and pull-down impedance of 1.75Ω. |
| 20 | GND | power_in | Ground pin; the exposed pad must be soldered to the PCB. |
| 21 | GND | power_in | Ground pin; the exposed pad must be soldered to the PCB. |
| 22 | PWMGL | output | Drives the gate of an external FET to connect a switching regulator output capacitor to the load, with pull-up impedance of 3.2Ω and pull-down impedance of 1.75Ω. |
| 23 | HG | output | Top FET gate drive signal controlling the high side external power FET, with pull-up impedance of 2.3Ω and pull-down impedance of 1.3Ω. |
| 24 | SW | passive | Lower rail for the floating high side driver that connects the two power FETs and the inductor externally. |
| 25 | CBOOT | power_out | Provides a floating 5V regulated supply for the high side FET driver, requiring an external Schottky diode from VCC_INT. |
| 26 | LG | output | Bottom FET gate drive signal controlling the low side external power FET, with pull-up impedance of 2.5Ω and pull-down impedance of 1.3Ω. |
| 27 | VCC_INT | power_out | Regulated 5V output for charging the CBOOT capacitor and powering digital and switching subcircuits, current limited to approximately 50mA. |
| 28 | VIN | power_in | Input supply pin that must be locally bypassed with a 1µF low ESR capacitor to ground, with an input voltage range of 6V to 36V. |
| 29 | GND | power_in | Exposed thermal pad connected to ground that must be soldered to the PCB. |
## Key specifications
| Parameter | Value |
|---|---|
| Manufacturer | Analog Devices |
| Package | QFN-28-EP(4x5) |
| Category | Display Modules / LED Drivers / Display Drivers |
| Pins | 29 |
## Electrical characteristics
Limits as printed in the datasheet (page.json `metadata.characteristics` carries them as data).
| Parameter | Symbol | Min | Typ | Max | Unit | Conditions | Page |
|---|---|---|---|---|---|---|---|
| Input Voltage Range | | 6 | | 36 | V | | 3 |
| Feedback Regulation Voltage | | 0.945 | 1 | 1.025 | V | VCTRL_H = 0V, VCTRL_L = 2V, VSENSE+ = 2V | 3 |
| Reference Voltage (VREF Pin) | | 1.96 | 2 | 2.04 | V | | 3 |
| Full Range SENSE+ to SENSE- | | 48 | 51 | 54 | mV | VCTRL_H = 1.5V, VSENSE- = 6V | 3 |
| Regulation Voltage (VCC_INT Pin) | | 4.7 | 5 | 5.2 | V | | 3 |
| Switching Frequency | fSW | 900 | 1000 | 1070 | kHz | RT = 40kΩ | 3 |
| Switching Frequency | fSW | 190 | 200 | 233 | kHz | RT = 200kΩ | 3 |
| VIN Pin Quiescent Current, Non-Switching Operation | | | 1.8 | 2.5 | mA | VPWM = VCTRL_SEL = 0V, Not Switching, RT = 40k | 3 |
| VIN Pin Quiescent Current, Shutdown Mode | | | 0.1 | 1 | µA | VEN/UVLO = 0V | 3 |
| EN/UVLO Pin Falling Threshold | | 1.49 | 1.55 | 1.61 | V | | 3 |
| CTRL_H and CTRL_L Pin Control Range | | 0 | | 1.5 | V | | 3 |
| Current Control Loop gm Amp Offset Voltage | | -3 | 0 | 3 | mV | VSENSE+ = 4V, VSENSE- = 4V | 4 |
| Current Control Loop gm | gm | 375 | 475 | 625 | µA/V | | 4 |
| CTRL_SEL High to PWMGL Low Delay | | | 10 | 40 | ns | | 4 |
| CTRL_SEL High to PWMGH High Delay | | | 150 | 200 | ns | | 4 |
| CTRL_SEL Low to PWMGH Low Delay | | | 30 | 60 | ns | | 4 |
| CTRL_SEL Low to PWMGL High Delay | | | 170 | 220 | ns | | 4 |
| Operating Temperature Range | | -40 | | 125 | °C | Per ordering table for LT3743EUFD#PBF | 2 |
| VIN Voltage | | | | 40 | V | | 2 |
| EN/UVLO Voltage | | | | 6 | V | | 2 |
| VREF Voltage | | | | 3 | V | | 2 |
| CTRL_L, CTRL_H, CTRL_T Voltage | | | | 3 | V | | 2 |
| PWM, CTRL_SEL Voltage | | | | 6 | V | | 2 |
| SENSE+ Voltage | | | | 40 | V | | 2 |
| SENSE- Voltage | | | | 40 | V | | 2 |
| VCH, VCL Voltage | | | | 3 | V | | 2 |
| SW Voltage | | | | 40 | V | | 2 |
| RT Voltage | | | | 3 | V | | 2 |
| FB Voltage | | | | 3 | V | | 2 |
| SS Voltage | | | | 6 | V | | 2 |
| SYNC Voltage | | | | 6 | V | | 2 |
| Storage Temperature Range | | -65 | | 150 | °C | | 2 |
| Thermal Resistance Junction to Ambient (QFN) | θJA | | 37 | | °C/W | 28-lead 4mm×5mm QFN (UFD package) | 2 |
| Maximum Junction Temperature (QFN) | TJMAX | | | 125 | °C | 28-lead 4mm×5mm QFN (UFD package) | 2 |
## CAD (KiCad official)
- Symbol: `LT3743EUFD#PBF`
- Footprint: `Package_DFN_QFN:QFN-28-1EP_4x5mm_P0.5mm_EP2.65x3.65mm`
- 3D model: QFN-28-EP(4x5) (KiCad packages3D, STEP)
- 3D model files: `lt3743eufd-pbf-etched.step` / `lt3743eufd-pbf-etched.glb` carry the MPN laser-etched on the die in a toggleable `Adom.LaserEtch` group (Fusion-ready); `lt3743eufd-pbf.step` / `lt3743eufd-pbf.glb` are the bare package body.
## Provenance
Data extracted from the manufacturer datasheet, not a distributor listing:
- **Datasheet:** [Analog Devices datasheet](https://www.analog.com/media/en/technical-documentation/data-sheets/3743fe.pdf) (28 pp, sha256 `422657c9cc941519`, retrieved 2026-11-02, tier: manufacturer)
- **Extractor:** parts-factory `2.0.0` / `extract_pins 0.3`, primary `claude-haiku-5-5` (text), consensus `claude-sonnet-5-5` (agreed), guards: pin_guards 0.1: passed. Pins are checked against the footprint pad set and their cited datasheet pages before publish.
- **CAD:** KiCad official libraries (CC-BY-SA 4.0).
[Datasheet PDF](docs/lt3743eufd-pbf-datasheet.pdf)