main
Download ZIP Propose a change
Generated by kicad-footprint-generator · KiCad file format 20260206
Name Last commit message Last updated
docs Publish 0.1.0 · Ray
viewers lt3743eufd-pbf: viewers · Ray
lt3743eufd-pbf-etched.glb Publish 0.1.0 · Ray
lt3743eufd-pbf-etched.step lt3743eufd-pbf: factory component page (tier=mfr) · Ray
lt3743eufd-pbf-hero.glb lt3743eufd-pbf: hero GLB from the etched model (keeps the MPN mark) · Ray
lt3743eufd-pbf-hero.overlay.json Publish 0.1.0 · Ray
lt3743eufd-pbf.glb Publish 0.1.0 · Ray
lt3743eufd-pbf.kicad_mod Publish 0.1.0 · Ray
lt3743eufd-pbf.kicad_sym Publish 0.1.0 · Ray
lt3743eufd-pbf.lbr Publish 0.1.0 · Ray
lt3743eufd-pbf.step Publish 0.1.0 · Ray
package.json Publish 0.1.1 · Ray
page.json Publish 0.1.1 · Ray
README.md Publish 0.1.0 · Ray
verification.json Verified: Published by the parts factory: tier mfr, 29 pins · Ray

LT3743EUFD#PBF

Analog Devices · LED Drivers · QFN-28-EP(4x5)

LT3743EUFD#PBF from Analog Devices, in a QFN-28-EP(4x5). Pinout and pin descriptions extracted from the manufacturer datasheet (extract_pins, cross-checked by a second model); symbol, footprint, and 3D from KiCad-official CAD.

Pinout

Pin Name Type Function
1 GND power_in Ground pin; the exposed pad must be soldered to the PCB.
2 EN/UVLO input Enable pin that turns on the internal bias core and subregulators at 1.55V, has no pull-up or pull-down, and full shutdown occurs at approximately 0.5V.
3 VREF power_out Buffered 2V reference capable of 0.5mA drive.
4 CTRL_T input Thermal control input that reduces the regulated current level for both CTRL_L and CTRL_H levels.
5 GND power_in Ground pin; the exposed pad must be soldered to the PCB.
6 CTRL_H input Sets the high level regulated output current and overcurrent set point, with the input internally clamped to a maximum of 1.5V.
7 CTRL_L input Sets the low level regulated output current, and should not be higher than the CTRL_H voltage.
8 SS passive Soft-start pin with an external capacitor to ground that limits regulated current during start-up, with a 5.5µA charging current.
9 GND power_in Ground pin; the exposed pad must be soldered to the PCB.
10 FB input Feedback pin for overvoltage protection with a feedback voltage of 1V, where exceeding 1.3V triggers the overvoltage lockout.
11 SENSE+ input Inverting input of the average current mode loop error amplifier, connected to the external current sense resistor RS.
12 SENSE- input Noninverting input of the average current mode loop error amplifier, through which the reference current flows out of the pin to the LED side of the sense resistor RS.
13 VCL passive Provides average current loop compensation for low level current regulation, with typical values of 15k to 80k for the resistor and 2nF to 10nF for the capacitor.
14 VCH passive Provides average current loop compensation for high level current regulation, with typical values of 15k to 80k for the resistor and 2nF to 10nF for the capacitor.
15 RT passive A resistor to ground sets the switching frequency between 200kHz and 1MHz, is current limited to 60µA, and must not be left open.
16 SYNC input Frequency synchronization pin with a synchronization range of 240kHz to 1.2MHz, which should be grounded when not in use.
17 CTRL_SEL input Selects between high current control CTRL_H and low current control CTRL_L for current level dimming, and should be grounded when not in use.
18 PWM input Input pin for PWM dimming of the LED where low terminates all switching and disconnects the output caps, and it should be pulled to VCC_INT when not in use.
19 PWMGH output Drives the gate of an external FET to connect a switching regulator output capacitor to the load, with pull-up impedance of 3.2Ω and pull-down impedance of 1.75Ω.
20 GND power_in Ground pin; the exposed pad must be soldered to the PCB.
21 GND power_in Ground pin; the exposed pad must be soldered to the PCB.
22 PWMGL output Drives the gate of an external FET to connect a switching regulator output capacitor to the load, with pull-up impedance of 3.2Ω and pull-down impedance of 1.75Ω.
23 HG output Top FET gate drive signal controlling the high side external power FET, with pull-up impedance of 2.3Ω and pull-down impedance of 1.3Ω.
24 SW passive Lower rail for the floating high side driver that connects the two power FETs and the inductor externally.
25 CBOOT power_out Provides a floating 5V regulated supply for the high side FET driver, requiring an external Schottky diode from VCC_INT.
26 LG output Bottom FET gate drive signal controlling the low side external power FET, with pull-up impedance of 2.5Ω and pull-down impedance of 1.3Ω.
27 VCC_INT power_out Regulated 5V output for charging the CBOOT capacitor and powering digital and switching subcircuits, current limited to approximately 50mA.
28 VIN power_in Input supply pin that must be locally bypassed with a 1µF low ESR capacitor to ground, with an input voltage range of 6V to 36V.
29 GND power_in Exposed thermal pad connected to ground that must be soldered to the PCB.

Key specifications

Parameter Value
Manufacturer Analog Devices
Package QFN-28-EP(4x5)
Category Display Modules / LED Drivers / Display Drivers
Pins 29

Electrical characteristics

Limits as printed in the datasheet (page.json metadata.characteristics carries them as data).

Parameter Symbol Min Typ Max Unit Conditions Page
Input Voltage Range 6 36 V 3
Feedback Regulation Voltage 0.945 1 1.025 V VCTRL_H = 0V, VCTRL_L = 2V, VSENSE+ = 2V 3
Reference Voltage (VREF Pin) 1.96 2 2.04 V 3
Full Range SENSE+ to SENSE- 48 51 54 mV VCTRL_H = 1.5V, VSENSE- = 6V 3
Regulation Voltage (VCC_INT Pin) 4.7 5 5.2 V 3
Switching Frequency fSW 900 1000 1070 kHz RT = 40kΩ 3
Switching Frequency fSW 190 200 233 kHz RT = 200kΩ 3
VIN Pin Quiescent Current, Non-Switching Operation 1.8 2.5 mA VPWM = VCTRL_SEL = 0V, Not Switching, RT = 40k 3
VIN Pin Quiescent Current, Shutdown Mode 0.1 1 µA VEN/UVLO = 0V 3
EN/UVLO Pin Falling Threshold 1.49 1.55 1.61 V 3
CTRL_H and CTRL_L Pin Control Range 0 1.5 V 3
Current Control Loop gm Amp Offset Voltage -3 0 3 mV VSENSE+ = 4V, VSENSE- = 4V 4
Current Control Loop gm gm 375 475 625 µA/V 4
CTRL_SEL High to PWMGL Low Delay 10 40 ns 4
CTRL_SEL High to PWMGH High Delay 150 200 ns 4
CTRL_SEL Low to PWMGH Low Delay 30 60 ns 4
CTRL_SEL Low to PWMGL High Delay 170 220 ns 4
Operating Temperature Range -40 125 °C Per ordering table for LT3743EUFD#PBF 2
VIN Voltage 40 V 2
EN/UVLO Voltage 6 V 2
VREF Voltage 3 V 2
CTRL_L, CTRL_H, CTRL_T Voltage 3 V 2
PWM, CTRL_SEL Voltage 6 V 2
SENSE+ Voltage 40 V 2
SENSE- Voltage 40 V 2
VCH, VCL Voltage 3 V 2
SW Voltage 40 V 2
RT Voltage 3 V 2
FB Voltage 3 V 2
SS Voltage 6 V 2
SYNC Voltage 6 V 2
Storage Temperature Range -65 150 °C 2
Thermal Resistance Junction to Ambient (QFN) θJA 37 °C/W 28-lead 4mm×5mm QFN (UFD package) 2
Maximum Junction Temperature (QFN) TJMAX 125 °C 28-lead 4mm×5mm QFN (UFD package) 2

CAD (KiCad official)

  • Symbol: LT3743EUFD#PBF
  • Footprint: Package_DFN_QFN:QFN-28-1EP_4x5mm_P0.5mm_EP2.65x3.65mm
  • 3D model: QFN-28-EP(4x5) (KiCad packages3D, STEP)
  • 3D model files: lt3743eufd-pbf-etched.step / lt3743eufd-pbf-etched.glb carry the MPN laser-etched on the die in a toggleable Adom.LaserEtch group (Fusion-ready); lt3743eufd-pbf.step / lt3743eufd-pbf.glb are the bare package body.

Provenance

Data extracted from the manufacturer datasheet, not a distributor listing:

  • Datasheet: Analog Devices datasheet (28 pp, sha256 422657c9cc941519, retrieved 2026-11-02, tier: manufacturer)
  • Extractor: parts-factory 2.0.0 / extract_pins 0.3, primary claude-haiku-5-5 (text), consensus claude-sonnet-5-5 (agreed), guards: pin_guards 0.1: passed. Pins are checked against the footprint pad set and their cited datasheet pages before publish.
  • CAD: KiCad official libraries (CC-BY-SA 4.0).

Datasheet PDF