3D Model
Open in new tab ↗
Loads when you scroll to it. Unloads after 5 minutes in the background.
Symbol & Footprint
Schematic Symbol
Open full view ↗Loads when you scroll to it. Unloads after 5 minutes in the background.
PCB Footprint
Open full view ↗Loads when you scroll to it. Unloads after 5 minutes in the background.
Datasheet
Open in new tab ↗Loads when you scroll to it. Unloads after 5 minutes in the background.
README
markdownLT3680EDD#TRPBF
Analog Devices · DC-DC Converters · DFN-10-EP(3x3)
LT3680EDD#TRPBF from Analog Devices, in a DFN-10-EP(3x3). Pinout and pin descriptions extracted from the manufacturer datasheet (extract_pins, cross-checked by a second model); symbol, footprint, and 3D from KiCad-official CAD.
Pinout
| Pin | Name | Type | Function |
|---|---|---|---|
| 1 | BD | power_in | Connects to the anode of the boost Schottky diode and supplies current to the internal regulator; bias from BD is used when it is driven above 3V. |
| 2 | BOOST | passive | Provides a drive voltage higher than the input voltage to the internal bipolar NPN power switch, with BOOST pin voltage limited to 30V above the SW pin. |
| 3 | SW | output | Output of the internal power switch; connect to the inductor, catch diode and boost capacitor. |
| 4 | VIN | power_in | Supplies current to the internal regulator and the internal power switch over the 3.6V to 36V input range, and must be locally bypassed. |
| 5 | RUN/SS | input | Tie to ground to shut down the regulator, tie to 2.5V or more for normal operation, and absolute maximum is 36V; this pin also sets the soft-start ramp. |
| 6 | SYNC | input | External clock synchronization input that should be grounded for Burst Mode operation at low loads, with clock edges faster than 1µs and never left floating. |
| 7 | PG | output | Open-collector power good output that remains low until the FB pin is within 9% of the final regulation voltage, with absolute maximum of 30V. |
| 8 | FB | input | Regulates to 0.790V; connect the feedback resistor divider tap to this pin, with absolute maximum of 5V. |
| 9 | VC | passive | Output of the internal error amplifier that controls peak switch current; tie an RC compensation network from this pin to ground, and it is clamped at 2.0V. |
| 10 | RT | passive | Oscillator resistor input; a resistor connected from this pin to ground sets the switching frequency. |
| 11 | GND | power_in | Exposed pad is ground and must be soldered to the PCB for thermal and electrical connection. |
Key specifications
| Parameter | Value |
|---|---|
| Manufacturer | Analog Devices |
| Package | DFN-10-EP(3x3) |
| Category | Power Supply Chip |
| Pins | 11 |
Electrical characteristics
Limits as printed in the datasheet (page.json metadata.characteristics carries them as data).
| Parameter | Symbol | Min | Typ | Max | Unit | Conditions | Page |
|---|---|---|---|---|---|---|---|
| Quiescent Current from VIN | IQ | 0.01 | 0.5 | µA | VRUN/SS = 0.2V | 3 | |
| Quiescent Current from VIN | IQ | 30 | 65 | µA | VBD = 3V, Not Switching | 3 | |
| Quiescent Current from VIN | IQ | 120 | 160 | µA | VBD = 0, Not Switching | 3 | |
| Quiescent Current from BD | IQ | 0.01 | 0.5 | µA | VRUN/SS = 0.2V | 3 | |
| Quiescent Current from BD | IQ | 90 | 130 | µA | VBD = 3V, Not Switching | 3 | |
| Quiescent Current from BD | IQ | 1 | 5 | µA | VBD = 0, Not Switching | 3 | |
| Feedback Voltage | VFB | 780 | 790 | 800 | mV | Over full operating temperature range (l) | 3 |
| Feedback Voltage | VFB | 775 | 790 | 805 | mV | 3 | |
| FB Pin Bias Current | IFB | 10 | 40 | nA | VFB = 0.8V, VC = 0.4V | 3 | |
| FB Voltage Line Regulation | 0.002 | 0.01 | %/V | 4V < VIN < 36V | 3 | ||
| Switching Frequency | fSW | 2.2 | 2.45 | 2.7 | MHz | RT = 8.66k | 3 |
| Switching Frequency | fSW | 1 | 1.1 | 1.25 | MHz | RT = 29.4k | 3 |
| Switching Frequency | fSW | 200 | 230 | 260 | kHz | RT = 187k | 3 |
| Minimum Input Voltage | VIN(MIN) | 3 | 3.6 | V | l | 3 | |
| Minimum Switch Off-Time | tOFF(MIN) | 60 | 150 | nS | l | 3 | |
| Switch Current Limit | ILIM | 4.6 | 5.4 | 6.6 | A | Duty Cycle = 5% | 3 |
| Switch VCESAT | VCESAT | 335 | mV | ISW = 3.5A | 3 | ||
| Boost Schottky Reverse Leakage | 0.02 | 2 | µA | VBOOST = 10V, VBD = 0V | 3 | ||
| Minimum Boost Voltage | 1.5 | 2 | V | Note 4 (l) | 3 | ||
| BOOST Pin Current | 35 | 50 | mA | ISW = 1A | 3 | ||
| RUN/SS Pin Current | 5 | 8 | µA | VRUN/SS = 2.5V | 3 | ||
| RUN/SS Input Voltage High | 2.5 | V | 3 | ||||
| RUN/SS Input Voltage Low | 0.2 | V | 3 | ||||
| PG Leakage | 0.1 | 1 | µA | VPG = 5V | 3 | ||
| PG Sink Current | 200 | 800 | µA | VPG = 0.4V (l) | 3 | ||
| SYNC Low Threshold | 0.5 | V | 3 | ||||
| SYNC High Threshold | 0.7 | V | 3 | ||||
| Operating Junction Temperature Range | TJ | -40 | 125 | °C | LT3680E | 2 | |
| VIN, RUN/SS Voltage | 36 | V | 2 | ||||
| BOOST Pin Above SW Pin | 30 | V | 2 | ||||
| FB, RT, VC Voltage | 5 | V | 2 | ||||
| PG, BD, SYNC Voltage | 30 | V | 2 | ||||
| Operating Junction Temperature Range (absolute) | TJ | -40 | 125 | °C | LT3680E | 2 | |
| Storage Temperature Range | TSTG | -65 | 150 | °C | 2 | ||
| Thermal Resistance Junction to Ambient | θJA | 45 | °C/W | DD package | 2 | ||
| Thermal Resistance Junction to Case | θJC | 10 | °C/W | DD package | 2 | ||
| Thermal Resistance Junction to Ambient (optimized layout) | θJA | 35 | °C/W | With thermal vias and extended ground plane per High Temperature Considerations | 18 |
CAD (KiCad official)
- Symbol:
LT3680EDD#TRPBF - Footprint:
Package_DFN_QFN:DFN-10-1EP_3x3mm_P0.5mm_EP1.55x2.48mm - 3D model: DFN-10-EP(3x3) (KiCad packages3D, STEP)
- 3D model files:
lt3680edd-trpbf-etched.step/lt3680edd-trpbf-etched.glbcarry the MPN laser-etched on the die in a toggleableAdom.LaserEtchgroup (Fusion-ready);lt3680edd-trpbf.step/lt3680edd-trpbf.glbare the bare package body.
Provenance
Data extracted from the manufacturer datasheet, not a distributor listing:
- Datasheet: Analog Devices datasheet (24 pp, sha256
6b5ca341795de2de, retrieved 2026-10-28, tier: manufacturer) - Extractor: parts-factory
2.0.0/extract_pins 0.3, primaryclaude-haiku-5-5(text), consensusclaude-sonnet-5-5(agreed), guards: pin_guards 0.1: passed. Pins are checked against the footprint pad set and their cited datasheet pages before publish. - CAD: KiCad official libraries (CC-BY-SA 4.0).