Generated by kicad-footprint-generator · KiCad file format 20260206
LT3669EUFD-2#PBF
Analog Devices · LIN Transceivers · QFN-28-EP(4x5)
LT3669EUFD-2#PBF from Analog Devices, in a QFN-28-EP(4x5). Pinout and pin descriptions extracted from the manufacturer datasheet (extract_pins, cross-checked by a second model). Symbol, footprint, and 3D from KiCad-official CAD.
Pinout
| Pin | Name | Type | Function |
|---|---|---|---|
| 1 | SC1 | output | CQ1 short-circuit detect open-collector output that pulls low on a CQ1 driver short or after thermal shutdown, and needs a 100k pull-up to the µC supply. |
| 2 | SC2 | output | Q2 short-circuit detect open-collector output that pulls low on a Q2 driver short or after thermal shutdown, and needs a 100k pull-up to the µC supply. |
| 3 | WAKE | output | Wake-up detect open-collector output that pulls low when driver 1 detects a wake-up pulse longer than 75µs at CQ1, and needs a 10k pull-up to the µC supply. |
| 4 | RXD1 | output | CQ1 receiver open-collector output, inverted with respect to line data CQ1, that should use a pull-up of 10k or less for COM3 performance. |
| 5 | TXEN1 | input | CQ1 driver enable that enables the push-pull CQ1 driver when high, and in open-collector mode carries the data signal with TXD1 held high (pull-down) or low (pull-up). |
| 6 | TXD1 | input | CQ1 driver input whose data polarity is inverted at the CQ1 driver output. |
| 7 | TXEN2 | input | Q2 driver enable that enables the push-pull Q2 driver when high, and in open-collector mode carries the data signal with TXD2 held high (pull-down) or low (pull-up). |
| 8 | TXD2 | input | Q2 driver input whose data polarity is inverted at the Q2 driver output. |
| 9 | Q2 | output | Q2 line driver output, inverted with respect to TXD2, which should have a capacitor (typically 470pF) to ground for improved performance. |
| 10 | CQ1 | bidirectional | CQ1 driver output and receiver input tied directly to the industrial line data terminal, with a capacitor (typically 470pF) to ground recommended for improved performance. |
| 11 | L+ | power_in | Power supply input and anode of the internal reverse polarity protection diode, connected to the industrial line supply and bypassed locally with at least 4.7µF. |
| 12 | EN/UVLO | input | Enable and undervoltage lockout pin that shuts the device down when pulled below 0.4V and sets a 1.5V UVLO threshold for the regulators and transceiver. |
| 13 | DIO | passive | Cathode of the internal reverse polarity protection diode that must not have a bypass capacitor unless an external L+ to DIO diode is used. |
| 14 | DA | passive | Diode anode for the LT3669-2 that connects to the anode of the external catch diode and lets internal circuitry sense catch diode current for frequency foldback in extreme situations. |
| 15 | SW | output | Output of the internal NPN power switch that connects to the inductor and boost capacitor. |
| 16 | BST | passive | Boost pin that supplies drive voltage above the input to the internal NPN switch and connects through a capacitor (typically 0.22µF) to SW. |
| 17 | BD | passive | Boost diode connection to the integrated Schottky from BD to BST that connects to the switching regulator output. |
| 18 | LDOIN | power_in | LDO power supply input that is the collector of the LDO power NPN and may be tied to the switching regulator output or DIO but not to L+. |
| 19 | LDO | power_out | Low dropout linear regulator output that must be bypassed to GND with at least 1µF of capacitance. |
| 20 | FBLDO | input | LDO feedback input that the device regulates to 0.794V, with a resistor divider tap setting the LDO output voltage. |
| 21 | FBOUT | input | Switching regulator feedback input that the device regulates to 0.794V, with a resistor divider tap setting the switching regulator output voltage. |
| 22 | RT | passive | Oscillator frequency programming pin where a resistor to AGND sets the switching frequency per Table 2. |
| 23 | AGND | power_in | Analog ground for bandgap references that connects to the ground of the RT, FBOUT, FBLDO, ILIM and CPOR passive components in a star connection to system ground. |
| 24 | SYNC | input | External clock synchronization input that is grounded for internal oscillator operation, or driven with a logic signal having pulse widths of at least 80ns. |
| 25 | SR | input | Slew rate control pin that is set low for reduced EMI in COM1/COM2 mode and set high for edge times suitable for COM3. |
| 26 | ILIM | input | Line driver current limit programming pin where a resistor to AGND sets the limit, and tying it to AGND gives a 140mA limit. |
| 27 | CPOR | passive | Reset delay timer pin where a capacitor to AGND sets a reset delay of 0.125ms/nF. |
| 28 | RST | output | Active low open-collector reset output that remains asserted for the CPOR-programmed delay after VOUT and VLDO rise above 92.7% of their set values. |
| 29 | GND | power_in | Exposed pad ground that must be tied to the ground plane and the industrial line ground terminal and soldered to the PCB for proper operation. |
Key specifications
| Parameter | Value |
|---|---|
| Manufacturer | Analog Devices |
| Package | QFN-28-EP(4x5) |
| Category | Communication Interface Chip/UART/485/232 |
| Pins | 29 |
Electrical characteristics
Limits as printed in the datasheet (page.json metadata.characteristics carries them as data).
| Parameter | Symbol | Min | Typ | Max | Unit | Conditions | Page |
|---|---|---|---|---|---|---|---|
| L+ Undervoltage Lockout Threshold | 6.4 | 7.5 | V | VL+ Rising; full temp range | 3 | ||
| L+ Overvoltage Lockout Threshold | VOVTH | 40.5 | 43 | 45 | V | VL+ Rising; full temp range | 3 |
| Shutdown Current from L+ | 1.15 | 1.65 | mA | VEN/UVLO = 0.4V | 3 | ||
| Quiescent Current from L+ | 4 | 6 | mA | Not Switching | 3 | ||
| Switching Regulator Feedback Voltage | VFBOUT | 777 | 794 | 811 | mV | full temp range | 3 |
| FBOUT Pin Bias Current | -15 | -100 | nA | FBOUT Pin Voltage = 800mV; full temp range | 3 | ||
| Switching Frequency | 1.94 | 2.28 | 2.62 | MHz | RT = 5.36k | 3 | |
| Switching Frequency | 0.88 | 1.04 | 1.2 | MHz | RT = 19.1k | 3 | |
| Switching Frequency | 219 | 258 | 297 | kHz | RT = 107k | 3 | |
| Minimum Switch Off-Time | 130 | 210 | ns | RT = 19.1k; full temp range | 3 | ||
| Switch Current Limit (LT3669-2) | 480 | 650 | 820 | mA | LT3669-2; full temp range | 3 | |
| Catch Schottky Diode Current Limit to Stop Internal Oscillator (LT3669-2) | 330 | 450 | 570 | mA | LT3669-2; full temp range | 3 | |
| BST Pin Current (LT3669-2) | 10.5 | 15 | mA | ISW = -300mA (LT3669-2) | 4 | ||
| EN/UVLO Threshold Voltage | 1.44 | 1.5 | 1.56 | V | VEN/UVLO Rising; full temp range | 4 | |
| LDO Feedback Voltage | VFBLDO | 777 | 794 | 811 | mV | full temp range | 4 |
| LDO Current Limit | 151 | 180 | 235 | mA | full temp range | 4 | |
| LDO Dropout Voltage | 340 | mV | LDO Load Current = 150mA; full temp range | 4 | |||
| LDO Minimum Load Current | 150 | 175 | µA | full temp range | 4 | ||
| Reset Threshold as % of VFBOUT (VFBLDO) | VRSTTH | 90.4 | 92.7 | 95 | % | FBOUT (FBLDO) Pin Voltage Falling (Figure 6); full temp range | 4 |
| Reset Timeout Period | tRST | 10 | 12.5 | 15 | ms | CPOR = 100nF, RST RPU = 100k (Figure 6); full temp range | 4 |
| Thermal Shutdown Threshold (Junction Temperature Increasing) | 125 | 140 | 155 | °C | TJ Increasing | 4 | |
| Thermal Shutdown Threshold (Junction Temperature Decreasing) | 111 | 128 | 135 | °C | TJ Decreasing | 4 | |
| DC Driver Current, P-Switching Output (ON State) | IQH | 280 | 330 | 420 | mA | RILIM = 42.2k, 7.5V < VL+ < 40V; full temp range | 4 |
| DC Driver Current, N-Switching Output (ON State) | IQL | 280 | 330 | 420 | mA | RILIM = 42.2k, 7.5V < VL+ < 40V; full temp range | 4 |
| Residual Voltage High (VL+ to VCQ1,Q2) | VRQH | 1.5 | 2.1 | V | ICQ1,Q2 = -250mA; full temp range | 4 | |
| VRQH (VRQL) Pulsing Threshold | 2.7 | 2.95 | 3.2 | V | VRQH (VRQL) Increasing | 4 | |
| Receiver Input Threshold “H” | VTHH | 10.5 | 11.8 | 13 | V | VL+ > 18V (Figure 14); full temp range | 4 |
| Receiver Input Threshold “L” | VTHL | 8 | 9.6 | 11.2 | V | VL+ > 18V (Figure 14); full temp range | 4 |
| Maximum Data Transfer Rate (COM1/COM2) | fDTR | 38.4 | kb/s | CCQ1,Q2 ≤ 4nF; VSR ≤ 0.4V (for COM1/COM2); full temp range | 5 | ||
| Propagation Delay, Receiver (COM1/COM2) | tPHLR, tPLHR | 4.6 | 6.5 | µs | RXD1 Pull-Up Resistor = 5k (Figure 4); VSR ≤ 0.4V (for COM1/COM2); full temp range | 6 | |
| Minimum Wake-Up Pulse Duration to Be Acknowledged | tDWU | 55 | 75 | µs | RPU = RPD = 10k (Figure 7); WAKE Pull-Up Resistor = 5k; full temp range | 5 | |
| Rise Time (COM1/COM2) | tDR | 1.6 | 5.2 | µs | CCQ1,Q2 ≤ 4nF (Figure 1); VSR ≤ 0.4V (for COM1/COM2); full temp range | 5 | |
| Propagation Delay, Driver (COM1/COM2) | tPHLD, tPLHD | 3.3 | 6 | µs | CCQ1,Q2 ≤ 4nF (Figure 2); VSR ≤ 0.4V (for COM1/COM2); full temp range | 5 | |
| CQ1, Q2 Pin Leakage Current | -3 | 3 | µA | -40°C to 125°C, VTXENn < 0.4V | 4 | ||
| Minimum BST Voltage | 1.4 | 1.8 | V | Note 7 | 3 | ||
| Switch VCESAT (VDIO, VSW) | 550 | mV | ISW = -300mA (LT3669-2) | 3 | |||
| Boost Schottky Diode Forward Voltage Drop | 750 | mV | IBST = -15mA (LT3669-2) | 3 | |||
| Reverse Protection Diode Forward Voltage Drop | 840 | mV | IDIO = -300mA (LT3669-2) | 3 | |||
| L+, EN/UVLO Voltage | -60 | 60 | V | Note 3 | 2 | ||
| CQ1, Q2 Voltage | -60 | 60 | V | 2 | |||
| (L+ to CQ1), (L+ to Q2) Voltage | -60 | 60 | V | 2 | |||
| DIO, LDOIN Voltage | -0.3 | 60 | V | Note 3 | 2 | ||
| LDO Voltage | 8 | V | 2 | ||||
| LDO Above LDOIN Voltage | 0.3 | V | 2 | ||||
| FBOUT, FBLDO, SYNC Voltage | 6 | V | 2 | ||||
| CPOR, RT, ILIM Voltage | 3 | V | 2 | ||||
| Operating Junction Temperature Range (LT3669E) | -40 | 125 | °C | LT3669E (Notes 4 and 5) | 2 | ||
| Storage Temperature Range | -65 | 150 | °C | 2 | |||
| Supply Voltage Operating Range | VL+ | 7.5 | 40 | V | Features: operation from 7.5V to 40V | 1 | |
| Thermal Resistance, Junction to Ambient | θJA | 44 | °C/W | 2 | |||
| Thermal Resistance, Junction to Case | θJC | 8 | °C/W | 2 |
CAD (KiCad official)
- Symbol:
LT3669EUFD-2#PBF - Footprint:
Package_DFN_QFN:QFN-28-1EP_4x5mm_P0.5mm_EP2.65x3.65mm - 3D model: QFN-28-EP(4x5), generated from the KiCad footprint (body from the F.Fab outline, terminals on the pads, 0.75 mm tall, datasheet A, nominal). Neither the vendor nor KiCad ships a 3D model for this package, so the dimensions come from the datasheet drawing where it was read and are defaults otherwise (see provenance.model_3d_generated), not the manufacturer's CAD (STEP)
- 3D model files:
lt3669eufd-2-etched.step/lt3669eufd-2-etched.glbcarry the MPN laser-etched on the die in a toggleableAdom.LaserEtchgroup (Fusion-ready);lt3669eufd-2.step/lt3669eufd-2.glbare the bare package body.
Provenance
Data extracted from the manufacturer datasheet, not a distributor listing:
- Datasheet: Analog Devices datasheet (40 pp, sha256
60300dd82eb00d53, retrieved 2026-11-12, tier: manufacturer) - Extractor: parts-factory
2.0.0/extract_pins 0.3, primaryclaude-haiku-5-5(text), consensusclaude-sonnet-5-5(agreed), guards: pin_guards 0.1: passed. Pins are checked against the footprint pad set and their cited datasheet pages before publish. - CAD: KiCad official libraries (CC-BY-SA 4.0).