3D Model
Open in new tab ↗
Loads when you scroll to it. Unloads after 5 minutes in the background.
Symbol & Footprint
Schematic Symbol
Open full view ↗Loads when you scroll to it. Unloads after 5 minutes in the background.
PCB Footprint
Open full view ↗Loads when you scroll to it. Unloads after 5 minutes in the background.
Datasheet
Open in new tab ↗Loads when you scroll to it. Unloads after 5 minutes in the background.
README
markdownLT3581EDE#PBF
Analog Devices · DC-DC Converters · DFN-14(3x4)
LT3581EDE#PBF from Analog Devices, in a DFN-14(3x4). Pinout and pin descriptions extracted from the manufacturer datasheet (extract_pins, cross-checked by a second model); symbol, footprint, and 3D from KiCad-official CAD.
Pinout
| Pin | Name | Type | Function |
|---|---|---|---|
| 1 | FB | input | Positive and negative feedback pin; tie a resistor from FB to VOUT, RFB = (VOUT - 1.215V)/83.3µA for boost/SEPIC or ( |
| 2 | VC | passive | Error amplifier output pin where the external compensation network is tied. |
| 3 | GATE | output | PMOS gate drive pull-down current source for output short-circuit protection or output disconnect, with maximum pull-down current of 933µA at SS voltages above 500mV. |
| 4 | FAULT | bidirectional | Active-low bidirectional fault indication pin, pulled low (below 750mV) externally or internally to signal a fault, needs a pull-up above 1V for no-fault operation. |
| 5 | VIN | power_in | Input supply pin that must be locally bypassed. |
| 6 | SW1 | passive | Master switch pin, the collector of the internal master NPN power switch; minimize connected metal trace area to minimize EMI. |
| 7 | SW1 | passive | Master switch pin, the collector of the internal master NPN power switch; minimize connected metal trace area to minimize EMI. |
| 8 | SW2 | passive | Slave switch pin, the collector of the internal slave NPN power switch; minimize connected metal trace area to minimize EMI. |
| 9 | SW2 | passive | Slave switch pin, the collector of the internal slave NPN power switch; minimize connected metal trace area to minimize EMI. |
| 10 | CLKOUT | output | Clock output pin for synchronizing other regulators, also usable as a junction temperature monitor via duty cycle, and meant to drive capacitive loads up to 50pF only. |
| 11 | SHDN | input | Shutdown pin that works with the UVLO circuit; drive below 300mV to disable the chip and above 1.33V (typical) to enable it and restart soft-start; do not float. |
| 12 | RT | passive | Timing resistor pin; a resistor to ground sets the free-running switching frequency; do not float. |
| 13 | SS | passive | Soft-start pin for a soft-start capacitor, charged by a nominal 250k resistor to about 2.1V on start-up and used in the fault timeout sequence. |
| 14 | SYNC | input | Synchronization input; drive with a clock whose high level exceeds 1.3V and low level is below 0.4V, or drive below 0.4V to revert to the internal free-running clock. |
| 15 | GND | power_in | Exposed pad ground that must be soldered directly to the local ground plane. |
Key specifications
| Parameter | Value |
|---|---|
| Manufacturer | Analog Devices |
| Package | DFN-14(3x4) |
| Category | Power Supply Chip |
| Pins | 15 |
Electrical characteristics
Limits as printed in the datasheet (page.json metadata.characteristics carries them as data).
| Parameter | Symbol | Min | Typ | Max | Unit | Conditions | Page |
|---|---|---|---|---|---|---|---|
| Minimum Input Voltage | 2.3 | 2.5 | V | 3 | |||
| VIN Overvoltage Lockout | 22.1 | 23.5 | 25 | V | 3 | ||
| Positive Feedback Voltage | 1.195 | 1.215 | 1.23 | V | 3 | ||
| Negative Feedback Voltage | 3 | 9 | 16 | mV | 3 | ||
| Positive FB Pin Bias Current | 81 | 83.3 | 85 | µA | VFB = Positive Feedback Voltage, Current into Pin | 3 | |
| Negative FB Pin Bias Current | 81 | 83.3 | 85.5 | µA | VFB = Negative Feedback Voltage, Current out of Pin | 3 | |
| Quiescent Current Not Switching | 1.9 | 2.3 | mA | Not Switching | 3 | ||
| Quiescent Current in Shutdown | 0 | 1 | µA | VSHDN = 0V | 3 | ||
| Reference Line Regulation | 0.01 | 0.05 | %/V | 2.5V ≤ VIN ≤ 20V | 3 | ||
| Switching Frequency, fOSC (RT = 34k) | fOSC | 2.25 | 2.5 | 2.75 | MHz | RT = 34k | 3 |
| Switching Frequency, fOSC (RT = 432k) | fOSC | 180 | 200 | 220 | kHz | RT = 432k | 3 |
| Switching Frequency Range | 200 | 2500 | kHz | Free-Running or Synchronizing | 3 | ||
| SYNC High Level for Synchronization | 1.3 | V | 3 | ||||
| SYNC Low Level for Synchronization | 0.4 | V | 3 | ||||
| SYNC Clock Pulse Duty Cycle | 20 | 80 | % | VSYNC = 0V to 2V | 3 | ||
| SW1 Current Limit | 1.9 | 2.4 | 3 | A | At All Duty Cycles | 3 | |
| SW1 + SW2 Current Limit | 3.3 | 4.3 | 5.4 | A | At All Duty Cycles, SW2/SW1 = 78% (Note 3) | 3 | |
| SW1 Leakage Current | 0.01 | 1 | µA | VSW1 = 5V | 3 | ||
| SW2 Leakage Current | 0.01 | 1 | µA | VSW2 = 5V | 3 | ||
| Soft-Start Charge Current | 5.7 | 8.7 | 11.3 | µA | VSS = 30mV, Current Flows Out of SS pin | 4 | |
| Soft-Start Discharge Current | 5.7 | 8.7 | 11.3 | µA | Part in FAULT, VSS = 2.1V, Current Flows into SS Pin | 4 | |
| Soft-Start High Detection Voltage | 1.65 | 1.8 | 1.95 | V | Part in FAULT | 4 | |
| Soft-Start Low Detection Voltage | 30 | 50 | 85 | mV | Part Exiting FAULT | 4 | |
| SHDN Minimum Input Voltage High | 1.27 | 1.33 | 1.41 | V | Active Mode, SHDN Rising (LT3581E, LT3581I) | 4 | |
| SHDN Minimum Input Voltage Low (falling threshold) | 1.24 | 1.3 | 1.38 | V | Active Mode, SHDN Falling (LT3581E, LT3581I, LT3581H) | 4 | |
| SHDN Input Voltage Low | 0.3 | V | Shutdown Mode | 4 | |||
| SHDN Pin Bias Current | 9.7 | 11.4 | 13.4 | µA | VSHDN = 3V | 4 | |
| CLKOUT Output Voltage High | 1.9 | 2.1 | 2.3 | V | CCLKOUT = 50pF | 4 | |
| CLKOUT Output Voltage Low | 5 | 200 | mV | CCLKOUT = 50pF | 4 | ||
| GATE Pull Down Current | 800 | 933 | 1100 | µA | VGATE = 3V (LT3581E, LT3581I) | 4 | |
| GATE Leakage Current | 0.01 | 1 | µA | VGATE = 50V, GATE Off | 4 | ||
| FAULT Output Voltage Low | 100 | 300 | mV | 50μA into FAULT Pin (LT3581E, LT3581I) | 4 | ||
| FAULT Leakage Current | 0.01 | 1 | µA | VFAULT = 40V, FAULT Off | 4 | ||
| FAULT Input Voltage Low | 700 | 750 | 800 | mV | 4 | ||
| FAULT Input Voltage High | 950 | 1000 | 1050 | mV | 4 | ||
| Operating Junction Temperature Range (LT3581E) | TJ | -40 | 125 | °C | LT3581E (Notes 2, 4) | 2 | |
| VIN Voltage | VIN | -0.3 | 40 | V | 2 | ||
| SW1/SW2 Voltage | -0.4 | 42 | V | 2 | |||
| RT Voltage | -0.3 | 5 | V | 2 | |||
| SS, FB Voltage | -0.3 | 2.5 | V | 2 | |||
| VC Voltage | -0.3 | 2 | V | 2 | |||
| SHDN Voltage | -0.3 | 40 | V | 2 | |||
| SYNC Voltage | -0.3 | 5.5 | V | 2 | |||
| GATE Voltage | -0.3 | 80 | V | 2 | |||
| FAULT Voltage | -0.3 | 40 | V | 2 | |||
| FAULT Current | -500 | 500 | µA | 2 | |||
| CLKOUT Voltage | -0.3 | 3 | V | 2 | |||
| CLKOUT Current | 1 | mA | 2 | ||||
| Storage Temperature Range | -65 | 150 | °C | 2 | |||
| Maximum Junction Temperature (TJMAX) | TJMAX | 125 | °C | DE14 package | 2 | ||
| Thermal Resistance, Junction to Ambient (θJA) | θJA | 43 | °C/W | DE14 package | 2 | ||
| Thermal Resistance, Junction to Case (θJC) | θJC | 4.3 | °C/W | DE14 package | 2 |
CAD (KiCad official)
- Symbol:
LT3581EDE#PBF - Footprint:
Package_DFN_QFN:DFN-14-1EP_3x4mm_P0.5mm_EP1.7x3.3mm - 3D model: DFN-14(3x4) (KiCad packages3D, STEP)
- 3D model files:
lt3581ede-pbf-etched.step/lt3581ede-pbf-etched.glbcarry the MPN laser-etched on the die in a toggleableAdom.LaserEtchgroup (Fusion-ready);lt3581ede-pbf.step/lt3581ede-pbf.glbare the bare package body.
Provenance
Data extracted from the manufacturer datasheet, not a distributor listing:
- Datasheet: Analog Devices datasheet (36 pp, sha256
c32042c990c741ab, retrieved 2026-10-31, tier: manufacturer) - Extractor: parts-factory
2.0.0/extract_pins 0.3, primaryclaude-haiku-5-5(text), consensusclaude-sonnet-5-5(agreed), guards: pin_guards 0.1: passed. Pins are checked against the footprint pad set and their cited datasheet pages before publish. - CAD: KiCad official libraries (CC-BY-SA 4.0).