main
Ray
Publish 0.1.0
8500bfe
LT3580MPMS8E#PBF
Analog Devices · DC-DC Converters · MSOP-8-EP
LT3580MPMS8E#PBF from Analog Devices, in a MSOP-8-EP. Pinout and pin descriptions extracted from the manufacturer datasheet (extract_pins, cross-checked by a second model); symbol, footprint, and 3D from KiCad-official CAD.
Pinout
| Pin | Name | Type | Function |
|---|---|---|---|
| 1 | FB | input | Positive and negative feedback pin; a resistor from VOUT to FB sets the output, with the FB reference at 1.215V for boost/SEPIC or 5mV for inverting. |
| 2 | VC | passive | Error amplifier output pin to which the external compensation network is tied. |
| 3 | VIN | power_in | Input supply pin (2.5V to 32V operating range) that must be locally bypassed. |
| 4 | SW | passive | Collector of the internal NPN power switch (2A, absolute max 42V); minimize connected metal trace area to reduce EMI. |
| 5 | SHDN | input | Shutdown/UVLO pin that disables the chip below 1.22V (LT3580MP) and activates it above 1.40V, restarting soft-start; do not float. |
| 6 | RT | passive | Timing resistor pin; a resistor to ground sets the switching frequency (200kHz to 2.5MHz); do not float. |
| 7 | SS | passive | Soft-start pin where a soft-start capacitor is placed, charged through a nominal 275k resistor to about 2.2V at start-up. |
| 8 | SYNC | input | Synchronization input driven by an external clock with high level above 1.3V and low level below 0.4V; drive below 0.4V to revert to the internal clock. |
| 9 | GND | power_in | Exposed pad ground that must be soldered directly to the local ground plane. |
Key specifications
| Parameter | Value |
|---|---|
| Manufacturer | Analog Devices |
| Package | MSOP-8-EP |
| Category | Power Supply Chip |
| Pins | 9 |
Electrical characteristics
Limits as printed in the datasheet (page.json metadata.characteristics carries them as data).
| Parameter | Symbol | Min | Typ | Max | Unit | Conditions | Page |
|---|---|---|---|---|---|---|---|
| Operating Voltage Range | VIN | 2.5 | 32 | V | 3 | ||
| Positive Feedback Voltage | 1.195 | 1.215 | 1.23 | V | 3 | ||
| Negative Feedback Voltage | 0 | 5 | 12 | mV | 3 | ||
| Positive FB Pin Bias Current | 81 | 83.3 | 85 | µA | VFB = Positive Feedback Voltage, Current Into Pin | 3 | |
| Negative FB Pin Bias Current | 81 | 83.3 | 85.5 | µA | VFB = Negative Feedback Voltage, Current Out of Pin (LT3580MP) | 3 | |
| Quiescent Current | IQ | 1 | 1.5 | mA | VSHDN = 2.5V, Not Switching | 3 | |
| Quiescent Current in Shutdown | 0 | 1 | µA | VSHDN = 0V | 3 | ||
| Reference Line Regulation | 0.01 | 0.05 | %/V | 2.5V ≤ VIN ≤ 32V | 3 | ||
| Switching Frequency | fOSC | 1.8 | 2 | 2.25 | MHz | RT = 45.3k (LT3580MP) | 3 |
| Switching Frequency | fOSC | 180 | 200 | 225 | kHz | RT = 464k (LT3580MP) | 3 |
| Switching Frequency Set Range | 200 | 2500 | kHz | SYNCing or Free Running | 3 | ||
| SYNC High Level for Synchronization | 1.3 | V | 3 | ||||
| SYNC Low Level for Synchronization | 0.4 | V | 3 | ||||
| SYNC Clock Pulse Duty Cycle | 35 | 65 | % | VSYNC = 0V to 2V | 3 | ||
| Switch Current Limit, Minimum Duty Cycle | 2.15 | 2.2 | 2.8 | A | Minimum Duty Cycle (Note 3) (LT3580MP) | 3 | |
| Switch Current Limit, Maximum Duty Cycle | 1.6 | 1.9 | 2.6 | A | Maximum Duty Cycle (Notes 3, 4) (LT3580MP) | 3 | |
| Switch Leakage Current | 0.01 | 1 | µA | VSW = 5V | 3 | ||
| Soft-Start Charging Current | 4 | 6 | 8 | µA | VSS = 0.5V | 3 | |
| SHDN Minimum Input Voltage High, Rising | 1.25 | 1.32 | 1.4 | V | Active Mode, SHDN Rising (LT3580H, LT3580MP) | 3 | |
| SHDN Minimum Input Voltage High, Falling | 1.22 | 1.29 | 1.35 | V | Active Mode, SHDN Falling (LT3580H, LT3580MP) | 3 | |
| SHDN Input Voltage Low | 0.3 | V | Shutdown Mode | 3 | |||
| SHDN Pin Bias Current | 9.7 | 11.6 | 13.4 | µA | VSHDN = 3V | 3 | |
| VIN Voltage | VIN | -0.3 | 32 | V | 2 | ||
| SW Voltage | -0.4 | 42 | V | 2 | |||
| RT Voltage | -0.3 | 5 | V | 2 | |||
| SS and FB Voltage | -0.3 | 2.5 | V | 2 | |||
| VC Voltage | -0.3 | 2 | V | 2 | |||
| SHDN Voltage | -0.3 | 32 | V | 2 | |||
| SYNC Voltage | -0.3 | 5.5 | V | 2 | |||
| Operating Junction Temperature Range (LT3580MP) | TJ | -55 | 125 | °C | Notes 2, 5 | 2 | |
| Storage Temperature Range | -65 | 150 | °C | 2 | |||
| Thermal Resistance Junction to Ambient, MS8E | θJA | 35 | 40 | °C/W | MS8E package, exposed pad soldered to PCB | 2 | |
| Error Amplifier Transconductance | 230 | µmhos | 3 | ||||
| Error Amplifier Voltage Gain | 70 | V/V | 3 | ||||
| Minimum Off-Time | 60 | ns | 3 | ||||
| Minimum On-Time | 100 | ns | 3 | ||||
| Switch VCESAT | 300 | mV | ISW = 1.5A | 3 |
Materials and finish
As the datasheet states them (page.json metadata.appearance; the 3D model's colours follow it).
| Part | Material | Colour / plating | Datasheet says | Page |
|---|---|---|---|---|
| contacts | copper | into the system ground plane at the C3 ground terminal. The cut ground copper at D1’s cathode is essential to | 16 |
CAD (KiCad official)
- Symbol:
LT3580MPMS8E#PBF - Footprint:
Package_SO:MSOP-8-1EP_3x3mm_P0.65mm_EP1.5x1.8mm - 3D model: MSOP-8-EP (KiCad packages3D, STEP)
- 3D model files:
lt3580mpms8e-pbf-etched.step/lt3580mpms8e-pbf-etched.glbcarry the MPN laser-etched on the die in a toggleableAdom.LaserEtchgroup (Fusion-ready);lt3580mpms8e-pbf.step/lt3580mpms8e-pbf.glbare the bare package body.
Provenance
Data extracted from the manufacturer datasheet, not a distributor listing:
- Datasheet: Analog Devices datasheet (28 pp, sha256
4dc8928ac64c889c, retrieved 2026-10-30, tier: manufacturer) - Extractor: parts-factory
2.0.0/extract_pins 0.3, primaryclaude-sonnet-5-5(text), consensusclaude-sonnet-5-5(agreed), guards: pin_guards 0.1: passed. Pins are checked against the footprint pad set and their cited datasheet pages before publish. - CAD: KiCad official libraries (CC-BY-SA 4.0).
# LT3580MPMS8E#PBF
**Analog Devices** · DC-DC Converters · MSOP-8-EP
LT3580MPMS8E#PBF from Analog Devices, in a MSOP-8-EP. Pinout and pin descriptions extracted from the manufacturer datasheet (extract_pins, cross-checked by a second model); symbol, footprint, and 3D from KiCad-official CAD.
## Pinout
| Pin | Name | Type | Function |
|---|---|---|---|
| 1 | FB | input | Positive and negative feedback pin; a resistor from VOUT to FB sets the output, with the FB reference at 1.215V for boost/SEPIC or 5mV for inverting. |
| 2 | VC | passive | Error amplifier output pin to which the external compensation network is tied. |
| 3 | VIN | power_in | Input supply pin (2.5V to 32V operating range) that must be locally bypassed. |
| 4 | SW | passive | Collector of the internal NPN power switch (2A, absolute max 42V); minimize connected metal trace area to reduce EMI. |
| 5 | SHDN | input | Shutdown/UVLO pin that disables the chip below 1.22V (LT3580MP) and activates it above 1.40V, restarting soft-start; do not float. |
| 6 | RT | passive | Timing resistor pin; a resistor to ground sets the switching frequency (200kHz to 2.5MHz); do not float. |
| 7 | SS | passive | Soft-start pin where a soft-start capacitor is placed, charged through a nominal 275k resistor to about 2.2V at start-up. |
| 8 | SYNC | input | Synchronization input driven by an external clock with high level above 1.3V and low level below 0.4V; drive below 0.4V to revert to the internal clock. |
| 9 | GND | power_in | Exposed pad ground that must be soldered directly to the local ground plane. |
## Key specifications
| Parameter | Value |
|---|---|
| Manufacturer | Analog Devices |
| Package | MSOP-8-EP |
| Category | Power Supply Chip |
| Pins | 9 |
## Electrical characteristics
Limits as printed in the datasheet (page.json `metadata.characteristics` carries them as data).
| Parameter | Symbol | Min | Typ | Max | Unit | Conditions | Page |
|---|---|---|---|---|---|---|---|
| Operating Voltage Range | VIN | 2.5 | | 32 | V | | 3 |
| Positive Feedback Voltage | | 1.195 | 1.215 | 1.23 | V | | 3 |
| Negative Feedback Voltage | | 0 | 5 | 12 | mV | | 3 |
| Positive FB Pin Bias Current | | 81 | 83.3 | 85 | µA | VFB = Positive Feedback Voltage, Current Into Pin | 3 |
| Negative FB Pin Bias Current | | 81 | 83.3 | 85.5 | µA | VFB = Negative Feedback Voltage, Current Out of Pin (LT3580MP) | 3 |
| Quiescent Current | IQ | | 1 | 1.5 | mA | VSHDN = 2.5V, Not Switching | 3 |
| Quiescent Current in Shutdown | | | 0 | 1 | µA | VSHDN = 0V | 3 |
| Reference Line Regulation | | | 0.01 | 0.05 | %/V | 2.5V ≤ VIN ≤ 32V | 3 |
| Switching Frequency | fOSC | 1.8 | 2 | 2.25 | MHz | RT = 45.3k (LT3580MP) | 3 |
| Switching Frequency | fOSC | 180 | 200 | 225 | kHz | RT = 464k (LT3580MP) | 3 |
| Switching Frequency Set Range | | 200 | | 2500 | kHz | SYNCing or Free Running | 3 |
| SYNC High Level for Synchronization | | | 1.3 | | V | | 3 |
| SYNC Low Level for Synchronization | | | 0.4 | | V | | 3 |
| SYNC Clock Pulse Duty Cycle | | 35 | | 65 | % | VSYNC = 0V to 2V | 3 |
| Switch Current Limit, Minimum Duty Cycle | | 2.15 | 2.2 | 2.8 | A | Minimum Duty Cycle (Note 3) (LT3580MP) | 3 |
| Switch Current Limit, Maximum Duty Cycle | | 1.6 | 1.9 | 2.6 | A | Maximum Duty Cycle (Notes 3, 4) (LT3580MP) | 3 |
| Switch Leakage Current | | | 0.01 | 1 | µA | VSW = 5V | 3 |
| Soft-Start Charging Current | | 4 | 6 | 8 | µA | VSS = 0.5V | 3 |
| SHDN Minimum Input Voltage High, Rising | | 1.25 | 1.32 | 1.4 | V | Active Mode, SHDN Rising (LT3580H, LT3580MP) | 3 |
| SHDN Minimum Input Voltage High, Falling | | 1.22 | 1.29 | 1.35 | V | Active Mode, SHDN Falling (LT3580H, LT3580MP) | 3 |
| SHDN Input Voltage Low | | | | 0.3 | V | Shutdown Mode | 3 |
| SHDN Pin Bias Current | | 9.7 | 11.6 | 13.4 | µA | VSHDN = 3V | 3 |
| VIN Voltage | VIN | -0.3 | | 32 | V | | 2 |
| SW Voltage | | -0.4 | | 42 | V | | 2 |
| RT Voltage | | -0.3 | | 5 | V | | 2 |
| SS and FB Voltage | | -0.3 | | 2.5 | V | | 2 |
| VC Voltage | | -0.3 | | 2 | V | | 2 |
| SHDN Voltage | | -0.3 | | 32 | V | | 2 |
| SYNC Voltage | | -0.3 | | 5.5 | V | | 2 |
| Operating Junction Temperature Range (LT3580MP) | TJ | -55 | | 125 | °C | Notes 2, 5 | 2 |
| Storage Temperature Range | | -65 | | 150 | °C | | 2 |
| Thermal Resistance Junction to Ambient, MS8E | θJA | 35 | | 40 | °C/W | MS8E package, exposed pad soldered to PCB | 2 |
| Error Amplifier Transconductance | | | 230 | | µmhos | | 3 |
| Error Amplifier Voltage Gain | | | 70 | | V/V | | 3 |
| Minimum Off-Time | | | 60 | | ns | | 3 |
| Minimum On-Time | | | 100 | | ns | | 3 |
| Switch VCESAT | | | 300 | | mV | ISW = 1.5A | 3 |
## Materials and finish
As the datasheet states them (page.json `metadata.appearance`; the 3D model's colours follow it).
| Part | Material | Colour / plating | Datasheet says | Page |
|---|---|---|---|---|
| contacts | copper | | into the system ground plane at the C3 ground terminal. The cut ground copper at D1’s cathode is essential to | 16 |
## CAD (KiCad official)
- Symbol: `LT3580MPMS8E#PBF`
- Footprint: `Package_SO:MSOP-8-1EP_3x3mm_P0.65mm_EP1.5x1.8mm`
- 3D model: MSOP-8-EP (KiCad packages3D, STEP)
- 3D model files: `lt3580mpms8e-pbf-etched.step` / `lt3580mpms8e-pbf-etched.glb` carry the MPN laser-etched on the die in a toggleable `Adom.LaserEtch` group (Fusion-ready); `lt3580mpms8e-pbf.step` / `lt3580mpms8e-pbf.glb` are the bare package body.
## Provenance
Data extracted from the manufacturer datasheet, not a distributor listing:
- **Datasheet:** [Analog Devices datasheet](https://www.analog.com/media/en/technical-documentation/data-sheets/lt3580.pdf) (28 pp, sha256 `4dc8928ac64c889c`, retrieved 2026-10-30, tier: manufacturer)
- **Extractor:** parts-factory `2.0.0` / `extract_pins 0.3`, primary `claude-sonnet-5-5` (text), consensus `claude-sonnet-5-5` (agreed), guards: pin_guards 0.1: passed. Pins are checked against the footprint pad set and their cited datasheet pages before publish.
- **CAD:** KiCad official libraries (CC-BY-SA 4.0).
[Datasheet PDF](docs/lt3580mpms8e-pbf-datasheet.pdf)