Loads when you scroll to it. Unloads after 5 minutes in the background.

Symbol & Footprint

Schematic Symbol

Open full view ↗
Loads when you scroll to it. Unloads after 5 minutes in the background.

PCB Footprint

Open full view ↗
Loads when you scroll to it. Unloads after 5 minutes in the background.
Loads when you scroll to it. Unloads after 5 minutes in the background.
Download PDF
Contents

README

markdown

LT3580MPMS8E#PBF

Analog Devices · DC-DC Converters · MSOP-8-EP

LT3580MPMS8E#PBF from Analog Devices, in a MSOP-8-EP. Pinout and pin descriptions extracted from the manufacturer datasheet (extract_pins, cross-checked by a second model); symbol, footprint, and 3D from KiCad-official CAD.

Pinout

Pin Name Type Function
1 FB input Positive and negative feedback pin; a resistor from VOUT to FB sets the output, with the FB reference at 1.215V for boost/SEPIC or 5mV for inverting.
2 VC passive Error amplifier output pin to which the external compensation network is tied.
3 VIN power_in Input supply pin (2.5V to 32V operating range) that must be locally bypassed.
4 SW passive Collector of the internal NPN power switch (2A, absolute max 42V); minimize connected metal trace area to reduce EMI.
5 SHDN input Shutdown/UVLO pin that disables the chip below 1.22V (LT3580MP) and activates it above 1.40V, restarting soft-start; do not float.
6 RT passive Timing resistor pin; a resistor to ground sets the switching frequency (200kHz to 2.5MHz); do not float.
7 SS passive Soft-start pin where a soft-start capacitor is placed, charged through a nominal 275k resistor to about 2.2V at start-up.
8 SYNC input Synchronization input driven by an external clock with high level above 1.3V and low level below 0.4V; drive below 0.4V to revert to the internal clock.
9 GND power_in Exposed pad ground that must be soldered directly to the local ground plane.

Key specifications

Parameter Value
Manufacturer Analog Devices
Package MSOP-8-EP
Category Power Supply Chip
Pins 9

Electrical characteristics

Limits as printed in the datasheet (page.json metadata.characteristics carries them as data).

Parameter Symbol Min Typ Max Unit Conditions Page
Operating Voltage Range VIN 2.5 32 V 3
Positive Feedback Voltage 1.195 1.215 1.23 V 3
Negative Feedback Voltage 0 5 12 mV 3
Positive FB Pin Bias Current 81 83.3 85 µA VFB = Positive Feedback Voltage, Current Into Pin 3
Negative FB Pin Bias Current 81 83.3 85.5 µA VFB = Negative Feedback Voltage, Current Out of Pin (LT3580MP) 3
Quiescent Current IQ 1 1.5 mA VSHDN = 2.5V, Not Switching 3
Quiescent Current in Shutdown 0 1 µA VSHDN = 0V 3
Reference Line Regulation 0.01 0.05 %/V 2.5V ≤ VIN ≤ 32V 3
Switching Frequency fOSC 1.8 2 2.25 MHz RT = 45.3k (LT3580MP) 3
Switching Frequency fOSC 180 200 225 kHz RT = 464k (LT3580MP) 3
Switching Frequency Set Range 200 2500 kHz SYNCing or Free Running 3
SYNC High Level for Synchronization 1.3 V 3
SYNC Low Level for Synchronization 0.4 V 3
SYNC Clock Pulse Duty Cycle 35 65 % VSYNC = 0V to 2V 3
Switch Current Limit, Minimum Duty Cycle 2.15 2.2 2.8 A Minimum Duty Cycle (Note 3) (LT3580MP) 3
Switch Current Limit, Maximum Duty Cycle 1.6 1.9 2.6 A Maximum Duty Cycle (Notes 3, 4) (LT3580MP) 3
Switch Leakage Current 0.01 1 µA VSW = 5V 3
Soft-Start Charging Current 4 6 8 µA VSS = 0.5V 3
SHDN Minimum Input Voltage High, Rising 1.25 1.32 1.4 V Active Mode, SHDN Rising (LT3580H, LT3580MP) 3
SHDN Minimum Input Voltage High, Falling 1.22 1.29 1.35 V Active Mode, SHDN Falling (LT3580H, LT3580MP) 3
SHDN Input Voltage Low 0.3 V Shutdown Mode 3
SHDN Pin Bias Current 9.7 11.6 13.4 µA VSHDN = 3V 3
VIN Voltage VIN -0.3 32 V 2
SW Voltage -0.4 42 V 2
RT Voltage -0.3 5 V 2
SS and FB Voltage -0.3 2.5 V 2
VC Voltage -0.3 2 V 2
SHDN Voltage -0.3 32 V 2
SYNC Voltage -0.3 5.5 V 2
Operating Junction Temperature Range (LT3580MP) TJ -55 125 °C Notes 2, 5 2
Storage Temperature Range -65 150 °C 2
Thermal Resistance Junction to Ambient, MS8E θJA 35 40 °C/W MS8E package, exposed pad soldered to PCB 2
Error Amplifier Transconductance 230 µmhos 3
Error Amplifier Voltage Gain 70 V/V 3
Minimum Off-Time 60 ns 3
Minimum On-Time 100 ns 3
Switch VCESAT 300 mV ISW = 1.5A 3

Materials and finish

As the datasheet states them (page.json metadata.appearance; the 3D model's colours follow it).

Part Material Colour / plating Datasheet says Page
contacts copper into the system ground plane at the C3 ground terminal. The cut ground copper at D1’s cathode is essential to 16

CAD (KiCad official)

  • Symbol: LT3580MPMS8E#PBF
  • Footprint: Package_SO:MSOP-8-1EP_3x3mm_P0.65mm_EP1.5x1.8mm
  • 3D model: MSOP-8-EP (KiCad packages3D, STEP)
  • 3D model files: lt3580mpms8e-pbf-etched.step / lt3580mpms8e-pbf-etched.glb carry the MPN laser-etched on the die in a toggleable Adom.LaserEtch group (Fusion-ready); lt3580mpms8e-pbf.step / lt3580mpms8e-pbf.glb are the bare package body.

Provenance

Data extracted from the manufacturer datasheet, not a distributor listing:

  • Datasheet: Analog Devices datasheet (28 pp, sha256 4dc8928ac64c889c, retrieved 2026-10-30, tier: manufacturer)
  • Extractor: parts-factory 2.0.0 / extract_pins 0.3, primary claude-sonnet-5-5 (text), consensus claude-sonnet-5-5 (agreed), guards: pin_guards 0.1: passed. Pins are checked against the footprint pad set and their cited datasheet pages before publish.
  • CAD: KiCad official libraries (CC-BY-SA 4.0).

Datasheet PDF