Loads when you scroll to it. Unloads after 5 minutes in the background.

Symbol & Footprint

Schematic Symbol

Open full view ↗
Loads when you scroll to it. Unloads after 5 minutes in the background.

PCB Footprint

Open full view ↗
Loads when you scroll to it. Unloads after 5 minutes in the background.
Loads when you scroll to it. Unloads after 5 minutes in the background.
Download PDF
Contents

README

markdown

LT3575EFE#TRPBF

Analog Devices · DC-DC Converters · TSSOP-16-EP

LT3575EFE#TRPBF from Analog Devices, in a TSSOP-16-EP. Pinout and pin descriptions extracted from the manufacturer datasheet (extract_pins, cross-checked by a second model); symbol, footprint, and 3D from KiCad-official CAD.

Pinout

Pin Name Type Function
1 NC unconnected No connect pin that can be left open or connected to any ground plane.
2 VIN power_in Input voltage pin (3V to 40V) supplying the internal start-up circuitry and serving as reference for the DCM comparator and feedback circuitry; must be locally bypassed with a capacitor.
3 SW passive Collector node of the 2.5A, 60V NPN output switch carrying large currents, so traces to switching components should be kept short.
4 SW passive Collector node of the 2.5A, 60V NPN output switch carrying large currents, so traces to switching components should be kept short.
5 BIAS power_in Bias voltage pin supplying the switch driver and internal circuitry, must be locally bypassed, and may be tied to VIN if no third winding is used and VIN ≤ 15V.
6 SHDN/UVLO input Shutdown/undervoltage lockout pin programmed by a resistor divider from VIN, with 1.22V rising threshold and 2.8μA hysteresis current, drawing no quiescent current below ~0.7V.
7 SS passive Soft-start pin where a capacitor limits start-up inrush current and output ramp rate, with switching starting at ~0.7V.
8 RILIM passive Maximum current limit adjust pin; a resistor to ground sets the current limit, with 10k giving the full switch current capability.
9 VC passive Compensation pin for the internal error amplifier; connect a series RC to ground, with an optional 100pF in parallel to reduce noise.
10 RFB input Input for the external feedback resistor connected to the transformer primary (VSW), with about 200μA average current during flyback, or connected to VIN in nonisolated applications.
11 RREF passive Input for the external ground-referred reference resistor, in the range of about 6k, which sets the output voltage with RFB.
12 TC passive Output voltage temperature compensation pin; a resistor to ground produces a PTAT current sourced into the RREF node, ITC = 0.55V/RTC.
13 TEST input Test pin used for testing purposes only that must be connected to ground for the part to operate properly.
14 GND power_in Ground pin, which should be connected to the ground plane along with the exposed pad.
15 NC unconnected No connect pin that can be left open or connected to any ground plane.
16 NC unconnected No connect pin that can be left open or connected to any ground plane.
17 GND power_in Exposed pad providing electrical and thermal contact to ground; must be soldered to the board and connected with many vias to an internal ground plane.

Key specifications

Parameter Value
Manufacturer Analog Devices
Package TSSOP-16-EP
Category Power Supply Chip
Pins 17

Electrical characteristics

Limits as printed in the datasheet (page.json metadata.characteristics carries them as data).

Parameter Symbol Min Typ Max Unit Conditions Page
Input Voltage Range VIN 3 40 V full operating temperature range 2
SHDN/UVLO Pin Threshold 1.15 1.22 1.32 V UVLO Pin Voltage Rising 2
SHDN/UVLO Pin Hysteresis Current 2.2 2.8 3.2 µA VUVLO = 1V 2
Switch Current Limit 2.8 3.5 4.2 A RILIM = 10k 2
RREF Voltage 1.21 1.23 1.25 V VIN = 3V 2
RREF Voltage (full temperature range) 1.2 1.26 V over full operating temperature range 2
RREF Voltage Line Regulation 0.01 0.03 %/V 3V < VIN < 40V 2
RREF Pin Bias Current 100 600 nA Note 3 2
BIAS Pin Voltage 2.9 3 3.1 V IBIAS = 30mA 3
Switch VCESAT VCESAT 75 125 mV ISW = 0.5A 2
Quiescent Current IQ 4.5 mA SS = 0V 2
Soft-Start Current 7 µA SS = 0.4V 2
Soft-Start Threshold 0.7 V 2
Maximum Switching Frequency 1000 kHz 2
Minimum Current Limit 400 mA VC = 0V 2
IREF Reference Current IREF 190 µA Measured at RFB Pin with RREF = 6.49k 3
Error Amplifier Voltage Gain 150 V/V VIN = 3V 3
Error Amplifier Transconductance 150 µmhos ΔI = 10µA, VIN = 3V 3
Minimum Switching Frequency 40 kHz VC = 0.35V 3
TC Current into RREF 27.5 µA RTC = 20.1k 3
VIN, SHDN/UVLO, RFB, BIAS Voltage 40 V 2
SS, VC, TC, RREF, RILIM Voltage 5 V 2
Maximum Junction Temperature TJMAX 125 °C 2
Operating Junction Temperature Range TJ -40 125 °C LT3575E 2
Storage Temperature Range TSTG -65 150 °C 2
Thermal Resistance Junction-to-Ambient θJA 38 °C/W FE package 2
Thermal Resistance Junction-to-Case θJC 10 °C/W FE package 2

CAD (KiCad official)

  • Symbol: LT3575EFE#TRPBF
  • Footprint: Package_SO:TSSOP-16-1EP_4.4x5mm_P0.65mm
  • 3D model: TSSOP-16-EP (KiCad packages3D, STEP)
  • 3D model files: lt3575efe-trpbf-etched.step / lt3575efe-trpbf-etched.glb carry the MPN laser-etched on the die in a toggleable Adom.LaserEtch group (Fusion-ready); lt3575efe-trpbf.step / lt3575efe-trpbf.glb are the bare package body.

Provenance

Data extracted from the manufacturer datasheet, not a distributor listing:

  • Datasheet: Analog Devices datasheet (24 pp, sha256 c581bbfcd62594dd, retrieved 2026-10-31, tier: manufacturer)
  • Extractor: parts-factory 2.0.0 / extract_pins 0.3, primary claude-sonnet-5-5 (text), consensus claude-sonnet-5-5 (agreed), guards: pin_guards 0.1: passed. Pins are checked against the footprint pad set and their cited datasheet pages before publish.
  • CAD: KiCad official libraries (CC-BY-SA 4.0).

Datasheet PDF