main
Ray
Publish 0.1.0
137302d
LT3571EUD#TRPBF
Analog Devices · DC-DC Converters · QFN-16-EP(3x3)
LT3571EUD#TRPBF from Analog Devices, in a QFN-16-EP(3x3). Pinout and pin descriptions extracted from the manufacturer datasheet (extract_pins, cross-checked by a second model); symbol, footprint, and 3D from KiCad-official CAD.
Pinout
| Pin | Name | Type | Function |
|---|---|---|---|
| 1 | NC | unconnected | No connect pin; leave unconnected. |
| 2 | APD | passive | APD cathode connection, rated 75V absolute maximum, with a 0.1μF capacitor recommended at this pin to suppress switching noise. |
| 3 | MONIN | power_in | Current monitor supply and inverting input of the current sense amplifier, rated 75V absolute maximum; a sense resistor between MONIN and VOUT sets the output current limit as 200mV/RSENSE, and MONIN connects directly to VOUT if that limit is not used. |
| 4 | VOUT | power_out | Boost converter output, rated 75V absolute maximum, with a capacitor placed between this pin and the GND plane and also serving as the noninverting input of the current sense amplifier. |
| 5 | SW | output | Switch pin, rated 75V absolute maximum; keep the trace length short to reduce EMI. |
| 6 | SW | output | Switch pin, rated 75V absolute maximum; keep the trace length short to reduce EMI. |
| 7 | GND | power_in | Ground, internally connected to pin 10; connect both GND pins to board ground for best performance. |
| 8 | SYNC | input | Frequency synchronization input with input low 0.4V maximum and input high 1.5V minimum (absolute maximum 5V); tie to ground if the feature is unused. |
| 9 | RT | input | Switching frequency programming pin, set by a resistor to GND (1.5V absolute maximum); do not leave this pin open. |
| 10 | GND | power_in | Ground, internally connected to pin 7; connect both GND pins to board ground for best performance. |
| 11 | VIN | power_in | Input supply pin with operating range 2.7V to 20V (20V absolute maximum); must be locally bypassed. |
| 12 | SHDN | input | Shutdown pin; tie to 1.5V or higher to enable the device and 0.4V or less to disable it, with an RC filter providing soft-start (20V absolute maximum). |
| 13 | VREF | power_out | Reference output that can supply up to 100μA, with pin voltage 1.200V to 1.240V at IREF = -100μA; do not overdrive, and bypass with a 10nF or larger capacitor (1.5V absolute maximum). |
| 14 | CTRL | input | Internal reference override pin that lets FB be adjusted between 0V and 1V; tie it higher than 1.2V to use the internal 1V reference (5V absolute maximum). |
| 15 | FB | input | Feedback pin connected to the output resistor divider tap (5V absolute maximum). |
| 16 | MON | output | Current monitor output that sources 20% of the APD current and converts it to a voltage through an external resistor; it is internally clamped to 11.5V (12V absolute maximum). |
| 17 | GND | power_in | Ground exposed pad on the package bottom that must be soldered to the PCB. |
Key specifications
| Parameter | Value |
|---|---|
| Manufacturer | Analog Devices |
| Package | QFN-16-EP(3x3) |
| Category | Power Supply Chip |
| Pins | 17 |
Electrical characteristics
Limits as printed in the datasheet (page.json metadata.characteristics carries them as data).
| Parameter | Symbol | Min | Typ | Max | Unit | Conditions | Page |
|---|---|---|---|---|---|---|---|
| Input Voltage (VIN), SHDN | VIN | 20 | V | 2 | |||
| VOUT, MONIN, APD Voltage | VOUT, MONIN, APD | 75 | V | 2 | |||
| MON Voltage | MON | 12 | V | 2 | |||
| SW Voltage | SW | 75 | V | 2 | |||
| CTRL, FB, SYNC Voltage | CTRL, FB, SYNC | 5 | V | 2 | |||
| RT, VREF Voltage | RT, VREF | 1.5 | V | 2 | |||
| Operating Ambient Temperature Range | TA | -40 | 125 | °C | Note 2 | 2 | |
| Operating Junction Temperature | TJ | -40 | 125 | °C | Note 2 | 2 | |
| Storage Temperature Range | TSTG | -65 | 150 | °C | 2 | ||
| Maximum Junction Temperature | TJMAX | 125 | °C | 2 | |||
| Junction-to-ambient thermal resistance | θJA | 68 | °C/W | 2 | |||
| Junction-to-case thermal resistance | θJC | 4.2 | °C/W | 2 | |||
| Minimum Operating Voltage | VIN | 2.7 | V | 2 | |||
| Maximum Operating Voltage | VIN | 20 | V | 2 | |||
| Supply Current | 1.7 | 2.2 | mA | VFB = 1.3V, Not Switching | 2 | ||
| Supply Current (shutdown) | 0.1 | 0.5 | μA | VSHDN = 0V | 2 | ||
| Feedback Voltage | VFB | 0.985 | 1 | 1.015 | V | VCTRL = 1.25V, VOUT = VMONIN | 2 |
| Feedback Voltage (wider temperature row) | VFB | 0.97 | 1 | 1.03 | V | VCTRL = 1.25V, VOUT = VMONIN | 2 |
| Feedback Line Regulation | 0.03 | 0.07 | %/V | 2.7V < VIN < 20V | 2 | ||
| Current Sense Voltage (VOUT, VMONIN) | 185 | 200 | 215 | mV | VOUT = 30V | 2 | |
| FB Pin Bias Current | IFB | 60 | 100 | nA | VFB = 0V | 2 | |
| VREF Pin Voltage | VREF | 1.2 | 1.222 | 1.24 | V | IREF = -100μA | 2 |
| VREF Pin Line Regulation | VREF | 0.03 | 0.07 | %V | 2.7V < VIN < 20V | 2 | |
| RT Voltage | RT | 1 | V | 2 | |||
| SYNC Resistance to GND | RSYNC | 45 | kΩ | VSYNC = 2V | 2 | ||
| SYNC Input Low | VSYNC | 0.4 | V | 2 | |||
| SYNC Input High | VSYNC | 1.5 | V | 2 | |||
| Switching Frequency | fSW | 0.85 | 1 | 1.15 | MHz | RT = 12.1k | 3 |
| Switching Frequency | fSW | 1.7 | 2 | 2.3 | MHz | RT = 4.22k | 3 |
| Switching Frequency | fSW | 210 | 250 | 280 | kHz | RT = 56.2k | 3 |
| Maximum Duty Cycle | DMAX | 95 | 97 | % | RT = 56.2k (250kHz) | 3 | |
| Maximum Duty Cycle | DMAX | 92 | 96 | % | SYNC = 300kHz Clock Signal, RT = 56.2k | 3 | |
| Maximum Duty Cycle | DMAX | 85 | 90 | % | RT = 12.1k (1MHz) | 3 | |
| Maximum Duty Cycle | DMAX | 75 | 80 | % | RT = 4.22k (2MHz) | 3 | |
| Switch Current Limit | ILIM | 370 | 470 | 570 | mA | 3 | |
| Switch VCESAT | VCESAT | 240 | mV | ISW = 200mA | 3 | ||
| Switch Leakage Current | ISW | 2 | μA | VSW = 75V | 3 | ||
| Schottky Forward Voltage | VF | 850 | mV | ISCHOTTKY = 200mA | 3 | ||
| Schottky Reverse Leakage | IR | 5 | μA | VOUT, VSW = 75V | 3 | ||
| SHDN Voltage High | VSHDN | 1.5 | V | 3 | |||
| SHDN Voltage Low | VSHDN | 0.4 | V | 3 | |||
| SHDN Pin Bias Current | ISHDN | 50 | 65 | μA | 3 | ||
| CTRL to FB Offset | -5 | 5 | 15 | mV | VCTRL = 0.5V | 3 | |
| CTRL to FB Offset (wider temperature row) | -10 | 5 | 20 | mV | VCTRL = 0.5V | 3 | |
| CTRL Input Bias Current | ICTRL | 20 | 100 | nA | Current Out of Pin, VCTRL = 0.5V | 3 | |
| APD Current Monitor Gain | 0.185 | 0.2 | 0.215 | 250nA ≤ IAPD < 10μA, 10V < VMONIN < 75V | 3 | ||
| APD Current Monitor Gain | 0.194 | 0.2 | 0.206 | 10μA ≤ IAPD ≤ 2.5mA, 20V < VMONIN < 75V | 3 | ||
| Monitor Output Voltage Clamp | 11.5 | V | 3 | ||||
| APD Monitor Voltage Drop | VMONIN, VAPD | 4.8 | 5 | 5.2 | V | IAPD = 1mA | 3 |
| MONIN Pin Current Limit | 30 | mA | VMONIN = 40V, VAPD = 0V | 3 |
CAD (KiCad official)
- Symbol:
LT3571EUD#TRPBF - Footprint:
Package_DFN_QFN:QFN-16-1EP_3x3mm_P0.5mm_EP1.7x1.7mm - 3D model: QFN-16-EP(3x3) (KiCad packages3D, STEP)
- 3D model files:
lt3571eud-trpbf-etched.step/lt3571eud-trpbf-etched.glbcarry the MPN laser-etched on the die in a toggleableAdom.LaserEtchgroup (Fusion-ready);lt3571eud-trpbf.step/lt3571eud-trpbf.glbare the bare package body.
Provenance
Data extracted from the manufacturer datasheet, not a distributor listing:
- Datasheet: Analog Devices datasheet (16 pp, sha256
df815c25cbca4b1b, retrieved 2026-10-31, tier: manufacturer) - Extractor: parts-factory
2.0.0/extract_pins 0.3, primaryclaude-haiku-5-5(text), consensusclaude-sonnet-5-5(agreed), guards: pin_guards 0.1: passed. Pins are checked against the footprint pad set and their cited datasheet pages before publish. - CAD: KiCad official libraries (CC-BY-SA 4.0).
# LT3571EUD#TRPBF
**Analog Devices** · DC-DC Converters · QFN-16-EP(3x3)
LT3571EUD#TRPBF from Analog Devices, in a QFN-16-EP(3x3). Pinout and pin descriptions extracted from the manufacturer datasheet (extract_pins, cross-checked by a second model); symbol, footprint, and 3D from KiCad-official CAD.
## Pinout
| Pin | Name | Type | Function |
|---|---|---|---|
| 1 | NC | unconnected | No connect pin; leave unconnected. |
| 2 | APD | passive | APD cathode connection, rated 75V absolute maximum, with a 0.1μF capacitor recommended at this pin to suppress switching noise. |
| 3 | MONIN | power_in | Current monitor supply and inverting input of the current sense amplifier, rated 75V absolute maximum; a sense resistor between MONIN and VOUT sets the output current limit as 200mV/RSENSE, and MONIN connects directly to VOUT if that limit is not used. |
| 4 | VOUT | power_out | Boost converter output, rated 75V absolute maximum, with a capacitor placed between this pin and the GND plane and also serving as the noninverting input of the current sense amplifier. |
| 5 | SW | output | Switch pin, rated 75V absolute maximum; keep the trace length short to reduce EMI. |
| 6 | SW | output | Switch pin, rated 75V absolute maximum; keep the trace length short to reduce EMI. |
| 7 | GND | power_in | Ground, internally connected to pin 10; connect both GND pins to board ground for best performance. |
| 8 | SYNC | input | Frequency synchronization input with input low 0.4V maximum and input high 1.5V minimum (absolute maximum 5V); tie to ground if the feature is unused. |
| 9 | RT | input | Switching frequency programming pin, set by a resistor to GND (1.5V absolute maximum); do not leave this pin open. |
| 10 | GND | power_in | Ground, internally connected to pin 7; connect both GND pins to board ground for best performance. |
| 11 | VIN | power_in | Input supply pin with operating range 2.7V to 20V (20V absolute maximum); must be locally bypassed. |
| 12 | SHDN | input | Shutdown pin; tie to 1.5V or higher to enable the device and 0.4V or less to disable it, with an RC filter providing soft-start (20V absolute maximum). |
| 13 | VREF | power_out | Reference output that can supply up to 100μA, with pin voltage 1.200V to 1.240V at IREF = -100μA; do not overdrive, and bypass with a 10nF or larger capacitor (1.5V absolute maximum). |
| 14 | CTRL | input | Internal reference override pin that lets FB be adjusted between 0V and 1V; tie it higher than 1.2V to use the internal 1V reference (5V absolute maximum). |
| 15 | FB | input | Feedback pin connected to the output resistor divider tap (5V absolute maximum). |
| 16 | MON | output | Current monitor output that sources 20% of the APD current and converts it to a voltage through an external resistor; it is internally clamped to 11.5V (12V absolute maximum). |
| 17 | GND | power_in | Ground exposed pad on the package bottom that must be soldered to the PCB. |
## Key specifications
| Parameter | Value |
|---|---|
| Manufacturer | Analog Devices |
| Package | QFN-16-EP(3x3) |
| Category | Power Supply Chip |
| Pins | 17 |
## Electrical characteristics
Limits as printed in the datasheet (page.json `metadata.characteristics` carries them as data).
| Parameter | Symbol | Min | Typ | Max | Unit | Conditions | Page |
|---|---|---|---|---|---|---|---|
| Input Voltage (VIN), SHDN | VIN | | | 20 | V | | 2 |
| VOUT, MONIN, APD Voltage | VOUT, MONIN, APD | | | 75 | V | | 2 |
| MON Voltage | MON | | | 12 | V | | 2 |
| SW Voltage | SW | | | 75 | V | | 2 |
| CTRL, FB, SYNC Voltage | CTRL, FB, SYNC | | | 5 | V | | 2 |
| RT, VREF Voltage | RT, VREF | | | 1.5 | V | | 2 |
| Operating Ambient Temperature Range | TA | -40 | | 125 | °C | Note 2 | 2 |
| Operating Junction Temperature | TJ | -40 | | 125 | °C | Note 2 | 2 |
| Storage Temperature Range | TSTG | -65 | | 150 | °C | | 2 |
| Maximum Junction Temperature | TJMAX | | | 125 | °C | | 2 |
| Junction-to-ambient thermal resistance | θJA | | 68 | | °C/W | | 2 |
| Junction-to-case thermal resistance | θJC | | 4.2 | | °C/W | | 2 |
| Minimum Operating Voltage | VIN | 2.7 | | | V | | 2 |
| Maximum Operating Voltage | VIN | | | 20 | V | | 2 |
| Supply Current | | | 1.7 | 2.2 | mA | VFB = 1.3V, Not Switching | 2 |
| Supply Current (shutdown) | | | 0.1 | 0.5 | μA | VSHDN = 0V | 2 |
| Feedback Voltage | VFB | 0.985 | 1 | 1.015 | V | VCTRL = 1.25V, VOUT = VMONIN | 2 |
| Feedback Voltage (wider temperature row) | VFB | 0.97 | 1 | 1.03 | V | VCTRL = 1.25V, VOUT = VMONIN | 2 |
| Feedback Line Regulation | | | 0.03 | 0.07 | %/V | 2.7V < VIN < 20V | 2 |
| Current Sense Voltage (VOUT, VMONIN) | | 185 | 200 | 215 | mV | VOUT = 30V | 2 |
| FB Pin Bias Current | IFB | | 60 | 100 | nA | VFB = 0V | 2 |
| VREF Pin Voltage | VREF | 1.2 | 1.222 | 1.24 | V | IREF = -100μA | 2 |
| VREF Pin Line Regulation | VREF | | 0.03 | 0.07 | %V | 2.7V < VIN < 20V | 2 |
| RT Voltage | RT | | 1 | | V | | 2 |
| SYNC Resistance to GND | RSYNC | | 45 | | kΩ | VSYNC = 2V | 2 |
| SYNC Input Low | VSYNC | | | 0.4 | V | | 2 |
| SYNC Input High | VSYNC | 1.5 | | | V | | 2 |
| Switching Frequency | fSW | 0.85 | 1 | 1.15 | MHz | RT = 12.1k | 3 |
| Switching Frequency | fSW | 1.7 | 2 | 2.3 | MHz | RT = 4.22k | 3 |
| Switching Frequency | fSW | 210 | 250 | 280 | kHz | RT = 56.2k | 3 |
| Maximum Duty Cycle | DMAX | 95 | | 97 | % | RT = 56.2k (250kHz) | 3 |
| Maximum Duty Cycle | DMAX | 92 | | 96 | % | SYNC = 300kHz Clock Signal, RT = 56.2k | 3 |
| Maximum Duty Cycle | DMAX | 85 | | 90 | % | RT = 12.1k (1MHz) | 3 |
| Maximum Duty Cycle | DMAX | 75 | | 80 | % | RT = 4.22k (2MHz) | 3 |
| Switch Current Limit | ILIM | 370 | 470 | 570 | mA | | 3 |
| Switch VCESAT | VCESAT | | | 240 | mV | ISW = 200mA | 3 |
| Switch Leakage Current | ISW | | | 2 | μA | VSW = 75V | 3 |
| Schottky Forward Voltage | VF | | | 850 | mV | ISCHOTTKY = 200mA | 3 |
| Schottky Reverse Leakage | IR | | | 5 | μA | VOUT, VSW = 75V | 3 |
| SHDN Voltage High | VSHDN | 1.5 | | | V | | 3 |
| SHDN Voltage Low | VSHDN | | | 0.4 | V | | 3 |
| SHDN Pin Bias Current | ISHDN | | 50 | 65 | μA | | 3 |
| CTRL to FB Offset | | -5 | 5 | 15 | mV | VCTRL = 0.5V | 3 |
| CTRL to FB Offset (wider temperature row) | | -10 | 5 | 20 | mV | VCTRL = 0.5V | 3 |
| CTRL Input Bias Current | ICTRL | | 20 | 100 | nA | Current Out of Pin, VCTRL = 0.5V | 3 |
| APD Current Monitor Gain | | 0.185 | 0.2 | 0.215 | | 250nA ≤ IAPD < 10μA, 10V < VMONIN < 75V | 3 |
| APD Current Monitor Gain | | 0.194 | 0.2 | 0.206 | | 10μA ≤ IAPD ≤ 2.5mA, 20V < VMONIN < 75V | 3 |
| Monitor Output Voltage Clamp | | | 11.5 | | V | | 3 |
| APD Monitor Voltage Drop | VMONIN, VAPD | 4.8 | 5 | 5.2 | V | IAPD = 1mA | 3 |
| MONIN Pin Current Limit | | | 30 | | mA | VMONIN = 40V, VAPD = 0V | 3 |
## CAD (KiCad official)
- Symbol: `LT3571EUD#TRPBF`
- Footprint: `Package_DFN_QFN:QFN-16-1EP_3x3mm_P0.5mm_EP1.7x1.7mm`
- 3D model: QFN-16-EP(3x3) (KiCad packages3D, STEP)
- 3D model files: `lt3571eud-trpbf-etched.step` / `lt3571eud-trpbf-etched.glb` carry the MPN laser-etched on the die in a toggleable `Adom.LaserEtch` group (Fusion-ready); `lt3571eud-trpbf.step` / `lt3571eud-trpbf.glb` are the bare package body.
## Provenance
Data extracted from the manufacturer datasheet, not a distributor listing:
- **Datasheet:** [Analog Devices datasheet](https://www.analog.com/media/en/technical-documentation/data-sheets/3571fa.pdf) (16 pp, sha256 `df815c25cbca4b1b`, retrieved 2026-10-31, tier: manufacturer)
- **Extractor:** parts-factory `2.0.0` / `extract_pins 0.3`, primary `claude-haiku-5-5` (text), consensus `claude-sonnet-5-5` (agreed), guards: pin_guards 0.1: passed. Pins are checked against the footprint pad set and their cited datasheet pages before publish.
- **CAD:** KiCad official libraries (CC-BY-SA 4.0).
[Datasheet PDF](docs/lt3571eud-trpbf-datasheet.pdf)