main
Ray
Publish 0.1.0
d31deab
LT3519EMS-2#PBF
Analog Devices · LED Drivers · MSOP-16
LT3519EMS-2#PBF from Analog Devices, in a MSOP-16. Pinout and pin descriptions extracted from the manufacturer datasheet (extract_pins, cross-checked by a second model); symbol, footprint, and 3D from KiCad-official CAD.
Pinout
| Pin | Name | Type | Function |
|---|---|---|---|
| 1 | GND | power_in | Power and signal ground; tie to GND plane for best thermal performance. |
| 2 | OPENLED | output | Open-collector open LED status pin that asserts when FB exceeds the FB regulation threshold minus 60mV (typ), requires an external pull-up resistor, rated to 40V. |
| 3 | PWM | input | PWM input where a low signal disables the oscillator and turns off the main switch, has an internal pull-down resistor (70kΩ typ), tie to VREF if not used. |
| 4 | SHDN/UVLO | input | Shutdown and undervoltage lockout pin with accurate 1.22V falling threshold and 2.2μA pull-down for hysteresis programming; tie to 0.4V or less to shut down (VIN current below 1μA); max 40V. |
| 5 | VIN | power_in | Input supply pin, operating range 3V to 30V, must be locally bypassed with a 1μF or larger ceramic capacitor placed close to it. |
| 6 | SW | passive | Switch pin (45V, 750mA internal low side switch) where the inductor is connected; minimize the trace to reduce EMI. |
| 7 | ANODE | passive | Internal Schottky diode anode pin, rated to 45V. |
| 8 | GND | power_in | Power and signal ground; tie to GND plane for best thermal performance. |
| 9 | GND | power_in | Power and signal ground; tie to GND plane for best thermal performance. |
| 10 | CATHODE | passive | Internal Schottky diode cathode pin, rated to 45V; place the output capacitor next to it. |
| 11 | ISP | input | Positive current sense resistor pin and noninverting input of the current sense amplifier, 0V to 45V rail-to-rail; input bias current increases with VISP-VISN. |
| 12 | ISN | input | Negative current sense resistor pin and inverting input of the current sense amplifier, 0V to 45V rail-to-rail. |
| 13 | FB | input | Voltage loop feedback pin regulated to 1.22V nominal for constant voltage regulation or open LED protection; do not leave open, connect to GND if not used. |
| 14 | CTRL | input | Current sense threshold adjustment pin: 0.1V to 1.0V linearly adjusts the threshold, above 1.2V gives full-scale 250mV; tie to VREF if not used. |
| 15 | VREF | power_out | Reference output pin, typically 2V, able to supply up to 100μA. |
| 16 | GND | power_in | Power and signal ground; tie to GND plane for best thermal performance. |
Key specifications
| Parameter | Value |
|---|---|
| Manufacturer | Analog Devices |
| Package | MSOP-16 |
| Category | Nixie Tube Driver/LED Driver |
| Pins | 16 |
Electrical characteristics
Limits as printed in the datasheet (page.json metadata.characteristics carries them as data).
| Parameter | Symbol | Min | Typ | Max | Unit | Conditions | Page |
|---|---|---|---|---|---|---|---|
| VIN Operating Voltage Range | VIN | 3 | 30 | V | Continuous Operation (Note 3) | 2 | |
| VIN Supply Current (Shutdown) | 0.1 | 1 | μA | SHDN/UVLO = 0V (Shutdown) | 2 | ||
| VIN Supply Current (Idle) | 2 | 3 | mA | PWM = 0V (Idle) | 2 | ||
| VIN Supply Current (Active, Not Switching) | 2.5 | 3.5 | mA | PWM > 1.5V, FB = 1.5V (Active, Not Switching) | 2 | ||
| Current Sense Voltage (VISP-VISN) | 240 | 250 | 260 | mV | ISP = 24V | 2 | |
| Current Sense Voltage (VISP-VISN) | 250 | mV | ISP = 0V | 2 | |||
| Zero Current Sense Voltage (VISP-VISN) | -15 | -6 | 3 | mV | ISP = 24V, CTRL = 100mV | 2 | |
| Current Sense Voltage Line Regulation | 0.02 | %/V | 2.5V < ISP < 45V | 2 | |||
| Switching Frequency | 1.9 | 2.2 | 2.4 | MHz | 2.2MHz (LT3519-2) | 3 | |
| Maximum Duty Cycle | 72 | 83 | % | 2.2MHz (LT3519-2) | 3 | ||
| Switch Current Limit | 750 | 980 | 1150 | mA | 3 | ||
| Switch VCESAT | VCESAT | 300 | mV | ISW = 500mA | 3 | ||
| Switch Leakage Current | 2 | μA | SW = 45V, PWM = 0V | 3 | |||
| CTRL for Full-Scale LED Current | 1.2 | V | 3 | ||||
| CTRL Pin Bias Current | 50 | 100 | nA | Current Out of Pin, CTRL = 0.1V | 3 | ||
| PWM Input High Voltage | 1.5 | V | 3 | ||||
| PWM Input Low Voltage | 0.8 | V | 3 | ||||
| PWM Pin Resistance to GND | 70 | kΩ | 3 | ||||
| FB Regulation Voltage | VFB | 1.19 | 1.22 | 1.25 | V | 3 | |
| FB Pin Bias Current | 60 | 120 | nA | Current Out of Pin, FB = 1V | 3 | ||
| ISP, ISN Idle Input Bias Current | 1 | μA | PWM = 0V, ISP = ISN = 24V | 3 | |||
| ISP, ISN Active Input Bias Current | 17 | μA | ISP = ISN = 24V, Current per Pin | 3 | |||
| Schottky Forward Drop | 0.8 | V | ISCHOTTKY = 500mA | 3 | |||
| Schottky Leakage Current | 4 | μA | CATHODE = 24V, ANODE = 0V | 3 | |||
| SHDN/UVLO Threshold Voltage Falling | 1.18 | 1.22 | 1.27 | V | 3 | ||
| SHDN/UVLO Input Low Voltage | 0.4 | V | IVIN Drops Below 1μA | 3 | |||
| SHDN/UVLO Pin Bias Current Low | 1.8 | 2.2 | 2.6 | μA | SHDN/UVLO = 1.15V | 3 | |
| SHDN/UVLO Pin Bias Current High | 10 | 100 | nA | SHDN/UVLO = 1.30V | 3 | ||
| VREF Output Voltage | 1.96 | 2 | 2.04 | V | -100μA ≤ IVREF ≤ 0μA | 3 | |
| VREF Output Pin Regulation | 0.04 | %/V | 3V < VIN < 40V | 3 | |||
| OPENLED Output Low | VOL | 240 | mV | IOPENLED = 1mA | 3 | ||
| OPENLED Leakage Current | 1 | μA | FB = 0V, OPENLED = 40V | 3 | |||
| VIN, OPENLED Voltage | VIN, OPENLED | 40 | V | Note 3 | 2 | ||
| SHDN/UVLO Voltage | 40 | V | Note 4 | 2 | |||
| SW, ISP, ISN, ANODE, CATHODE Voltage | 45 | V | 2 | ||||
| PWM, CTRL Voltage | 10 | V | 2 | ||||
| FB, VREF Voltage | 3 | V | 2 | ||||
| Operating Junction Temperature Range | -40 | 125 | °C | Note 2 | 2 | ||
| Maximum Junction Temperature | TJMAX | 125 | °C | 2 | |||
| Storage Temperature Range | -65 | 125 | °C | 2 | |||
| Thermal Resistance Junction to Ambient | θJA | 130 | °C/W | 16-Lead MSOP | 2 |
CAD (KiCad official)
- Symbol:
LT3519EMS-2#PBF - Footprint:
Package_SO:MSOP-16_3x4.039mm_P0.5mm - 3D model: MSOP-16 (KiCad packages3D, STEP)
- 3D model files:
lt3519ems-2-pbf-etched.step/lt3519ems-2-pbf-etched.glbcarry the MPN laser-etched on the die in a toggleableAdom.LaserEtchgroup (Fusion-ready);lt3519ems-2-pbf.step/lt3519ems-2-pbf.glbare the bare package body.
Provenance
Data extracted from the manufacturer datasheet, not a distributor listing:
- Datasheet: Analog Devices datasheet (20 pp, sha256
887e794b2bd96a8f, retrieved 2026-10-30, tier: manufacturer) - Extractor: parts-factory
2.0.0/extract_pins 0.3, primaryclaude-sonnet-5-5(text), consensusclaude-sonnet-5-5(agreed), guards: pin_guards 0.1: passed. Pins are checked against the footprint pad set and their cited datasheet pages before publish. - CAD: KiCad official libraries (CC-BY-SA 4.0).
# LT3519EMS-2#PBF
**Analog Devices** · LED Drivers · MSOP-16
LT3519EMS-2#PBF from Analog Devices, in a MSOP-16. Pinout and pin descriptions extracted from the manufacturer datasheet (extract_pins, cross-checked by a second model); symbol, footprint, and 3D from KiCad-official CAD.
## Pinout
| Pin | Name | Type | Function |
|---|---|---|---|
| 1 | GND | power_in | Power and signal ground; tie to GND plane for best thermal performance. |
| 2 | OPENLED | output | Open-collector open LED status pin that asserts when FB exceeds the FB regulation threshold minus 60mV (typ), requires an external pull-up resistor, rated to 40V. |
| 3 | PWM | input | PWM input where a low signal disables the oscillator and turns off the main switch, has an internal pull-down resistor (70kΩ typ), tie to VREF if not used. |
| 4 | SHDN/UVLO | input | Shutdown and undervoltage lockout pin with accurate 1.22V falling threshold and 2.2μA pull-down for hysteresis programming; tie to 0.4V or less to shut down (VIN current below 1μA); max 40V. |
| 5 | VIN | power_in | Input supply pin, operating range 3V to 30V, must be locally bypassed with a 1μF or larger ceramic capacitor placed close to it. |
| 6 | SW | passive | Switch pin (45V, 750mA internal low side switch) where the inductor is connected; minimize the trace to reduce EMI. |
| 7 | ANODE | passive | Internal Schottky diode anode pin, rated to 45V. |
| 8 | GND | power_in | Power and signal ground; tie to GND plane for best thermal performance. |
| 9 | GND | power_in | Power and signal ground; tie to GND plane for best thermal performance. |
| 10 | CATHODE | passive | Internal Schottky diode cathode pin, rated to 45V; place the output capacitor next to it. |
| 11 | ISP | input | Positive current sense resistor pin and noninverting input of the current sense amplifier, 0V to 45V rail-to-rail; input bias current increases with VISP-VISN. |
| 12 | ISN | input | Negative current sense resistor pin and inverting input of the current sense amplifier, 0V to 45V rail-to-rail. |
| 13 | FB | input | Voltage loop feedback pin regulated to 1.22V nominal for constant voltage regulation or open LED protection; do not leave open, connect to GND if not used. |
| 14 | CTRL | input | Current sense threshold adjustment pin: 0.1V to 1.0V linearly adjusts the threshold, above 1.2V gives full-scale 250mV; tie to VREF if not used. |
| 15 | VREF | power_out | Reference output pin, typically 2V, able to supply up to 100μA. |
| 16 | GND | power_in | Power and signal ground; tie to GND plane for best thermal performance. |
## Key specifications
| Parameter | Value |
|---|---|
| Manufacturer | Analog Devices |
| Package | MSOP-16 |
| Category | Nixie Tube Driver/LED Driver |
| Pins | 16 |
## Electrical characteristics
Limits as printed in the datasheet (page.json `metadata.characteristics` carries them as data).
| Parameter | Symbol | Min | Typ | Max | Unit | Conditions | Page |
|---|---|---|---|---|---|---|---|
| VIN Operating Voltage Range | VIN | 3 | | 30 | V | Continuous Operation (Note 3) | 2 |
| VIN Supply Current (Shutdown) | | | 0.1 | 1 | μA | SHDN/UVLO = 0V (Shutdown) | 2 |
| VIN Supply Current (Idle) | | | 2 | 3 | mA | PWM = 0V (Idle) | 2 |
| VIN Supply Current (Active, Not Switching) | | | 2.5 | 3.5 | mA | PWM > 1.5V, FB = 1.5V (Active, Not Switching) | 2 |
| Current Sense Voltage (VISP-VISN) | | 240 | 250 | 260 | mV | ISP = 24V | 2 |
| Current Sense Voltage (VISP-VISN) | | | 250 | | mV | ISP = 0V | 2 |
| Zero Current Sense Voltage (VISP-VISN) | | -15 | -6 | 3 | mV | ISP = 24V, CTRL = 100mV | 2 |
| Current Sense Voltage Line Regulation | | | 0.02 | | %/V | 2.5V < ISP < 45V | 2 |
| Switching Frequency | | 1.9 | 2.2 | 2.4 | MHz | 2.2MHz (LT3519-2) | 3 |
| Maximum Duty Cycle | | 72 | 83 | | % | 2.2MHz (LT3519-2) | 3 |
| Switch Current Limit | | 750 | 980 | 1150 | mA | | 3 |
| Switch VCESAT | VCESAT | | 300 | | mV | ISW = 500mA | 3 |
| Switch Leakage Current | | | 2 | | μA | SW = 45V, PWM = 0V | 3 |
| CTRL for Full-Scale LED Current | | | 1.2 | | V | | 3 |
| CTRL Pin Bias Current | | | 50 | 100 | nA | Current Out of Pin, CTRL = 0.1V | 3 |
| PWM Input High Voltage | | 1.5 | | | V | | 3 |
| PWM Input Low Voltage | | | | 0.8 | V | | 3 |
| PWM Pin Resistance to GND | | | 70 | | kΩ | | 3 |
| FB Regulation Voltage | VFB | 1.19 | 1.22 | 1.25 | V | | 3 |
| FB Pin Bias Current | | | 60 | 120 | nA | Current Out of Pin, FB = 1V | 3 |
| ISP, ISN Idle Input Bias Current | | | 1 | | μA | PWM = 0V, ISP = ISN = 24V | 3 |
| ISP, ISN Active Input Bias Current | | | 17 | | μA | ISP = ISN = 24V, Current per Pin | 3 |
| Schottky Forward Drop | | | 0.8 | | V | ISCHOTTKY = 500mA | 3 |
| Schottky Leakage Current | | | 4 | | μA | CATHODE = 24V, ANODE = 0V | 3 |
| SHDN/UVLO Threshold Voltage Falling | | 1.18 | 1.22 | 1.27 | V | | 3 |
| SHDN/UVLO Input Low Voltage | | | | 0.4 | V | IVIN Drops Below 1μA | 3 |
| SHDN/UVLO Pin Bias Current Low | | 1.8 | 2.2 | 2.6 | μA | SHDN/UVLO = 1.15V | 3 |
| SHDN/UVLO Pin Bias Current High | | | 10 | 100 | nA | SHDN/UVLO = 1.30V | 3 |
| VREF Output Voltage | | 1.96 | 2 | 2.04 | V | -100μA ≤ IVREF ≤ 0μA | 3 |
| VREF Output Pin Regulation | | | 0.04 | | %/V | 3V < VIN < 40V | 3 |
| OPENLED Output Low | VOL | | 240 | | mV | IOPENLED = 1mA | 3 |
| OPENLED Leakage Current | | | 1 | | μA | FB = 0V, OPENLED = 40V | 3 |
| VIN, OPENLED Voltage | VIN, OPENLED | | | 40 | V | Note 3 | 2 |
| SHDN/UVLO Voltage | | | | 40 | V | Note 4 | 2 |
| SW, ISP, ISN, ANODE, CATHODE Voltage | | | | 45 | V | | 2 |
| PWM, CTRL Voltage | | | | 10 | V | | 2 |
| FB, VREF Voltage | | | | 3 | V | | 2 |
| Operating Junction Temperature Range | | -40 | | 125 | °C | Note 2 | 2 |
| Maximum Junction Temperature | TJMAX | | | 125 | °C | | 2 |
| Storage Temperature Range | | -65 | | 125 | °C | | 2 |
| Thermal Resistance Junction to Ambient | θJA | | 130 | | °C/W | 16-Lead MSOP | 2 |
## CAD (KiCad official)
- Symbol: `LT3519EMS-2#PBF`
- Footprint: `Package_SO:MSOP-16_3x4.039mm_P0.5mm`
- 3D model: MSOP-16 (KiCad packages3D, STEP)
- 3D model files: `lt3519ems-2-pbf-etched.step` / `lt3519ems-2-pbf-etched.glb` carry the MPN laser-etched on the die in a toggleable `Adom.LaserEtch` group (Fusion-ready); `lt3519ems-2-pbf.step` / `lt3519ems-2-pbf.glb` are the bare package body.
## Provenance
Data extracted from the manufacturer datasheet, not a distributor listing:
- **Datasheet:** [Analog Devices datasheet](https://www.analog.com/media/en/technical-documentation/data-sheets/3519fa.pdf) (20 pp, sha256 `887e794b2bd96a8f`, retrieved 2026-10-30, tier: manufacturer)
- **Extractor:** parts-factory `2.0.0` / `extract_pins 0.3`, primary `claude-sonnet-5-5` (text), consensus `claude-sonnet-5-5` (agreed), guards: pin_guards 0.1: passed. Pins are checked against the footprint pad set and their cited datasheet pages before publish.
- **CAD:** KiCad official libraries (CC-BY-SA 4.0).
[Datasheet PDF](docs/lt3519ems-2-pbf-datasheet.pdf)