Loads when you scroll to it. Unloads after 5 minutes in the background.

Symbol & Footprint

Schematic Symbol

Open full view ↗
Loads when you scroll to it. Unloads after 5 minutes in the background.

PCB Footprint

Open full view ↗
Loads when you scroll to it. Unloads after 5 minutes in the background.
Loads when you scroll to it. Unloads after 5 minutes in the background.
Download PDF
Contents

README

markdown

LT3519EMS-2#PBF

Analog Devices · LED Drivers · MSOP-16

LT3519EMS-2#PBF from Analog Devices, in a MSOP-16. Pinout and pin descriptions extracted from the manufacturer datasheet (extract_pins, cross-checked by a second model); symbol, footprint, and 3D from KiCad-official CAD.

Pinout

Pin Name Type Function
1 GND power_in Power and signal ground; tie to GND plane for best thermal performance.
2 OPENLED output Open-collector open LED status pin that asserts when FB exceeds the FB regulation threshold minus 60mV (typ), requires an external pull-up resistor, rated to 40V.
3 PWM input PWM input where a low signal disables the oscillator and turns off the main switch, has an internal pull-down resistor (70kΩ typ), tie to VREF if not used.
4 SHDN/UVLO input Shutdown and undervoltage lockout pin with accurate 1.22V falling threshold and 2.2μA pull-down for hysteresis programming; tie to 0.4V or less to shut down (VIN current below 1μA); max 40V.
5 VIN power_in Input supply pin, operating range 3V to 30V, must be locally bypassed with a 1μF or larger ceramic capacitor placed close to it.
6 SW passive Switch pin (45V, 750mA internal low side switch) where the inductor is connected; minimize the trace to reduce EMI.
7 ANODE passive Internal Schottky diode anode pin, rated to 45V.
8 GND power_in Power and signal ground; tie to GND plane for best thermal performance.
9 GND power_in Power and signal ground; tie to GND plane for best thermal performance.
10 CATHODE passive Internal Schottky diode cathode pin, rated to 45V; place the output capacitor next to it.
11 ISP input Positive current sense resistor pin and noninverting input of the current sense amplifier, 0V to 45V rail-to-rail; input bias current increases with VISP-VISN.
12 ISN input Negative current sense resistor pin and inverting input of the current sense amplifier, 0V to 45V rail-to-rail.
13 FB input Voltage loop feedback pin regulated to 1.22V nominal for constant voltage regulation or open LED protection; do not leave open, connect to GND if not used.
14 CTRL input Current sense threshold adjustment pin: 0.1V to 1.0V linearly adjusts the threshold, above 1.2V gives full-scale 250mV; tie to VREF if not used.
15 VREF power_out Reference output pin, typically 2V, able to supply up to 100μA.
16 GND power_in Power and signal ground; tie to GND plane for best thermal performance.

Key specifications

Parameter Value
Manufacturer Analog Devices
Package MSOP-16
Category Nixie Tube Driver/LED Driver
Pins 16

Electrical characteristics

Limits as printed in the datasheet (page.json metadata.characteristics carries them as data).

Parameter Symbol Min Typ Max Unit Conditions Page
VIN Operating Voltage Range VIN 3 30 V Continuous Operation (Note 3) 2
VIN Supply Current (Shutdown) 0.1 1 μA SHDN/UVLO = 0V (Shutdown) 2
VIN Supply Current (Idle) 2 3 mA PWM = 0V (Idle) 2
VIN Supply Current (Active, Not Switching) 2.5 3.5 mA PWM > 1.5V, FB = 1.5V (Active, Not Switching) 2
Current Sense Voltage (VISP-VISN) 240 250 260 mV ISP = 24V 2
Current Sense Voltage (VISP-VISN) 250 mV ISP = 0V 2
Zero Current Sense Voltage (VISP-VISN) -15 -6 3 mV ISP = 24V, CTRL = 100mV 2
Current Sense Voltage Line Regulation 0.02 %/V 2.5V < ISP < 45V 2
Switching Frequency 1.9 2.2 2.4 MHz 2.2MHz (LT3519-2) 3
Maximum Duty Cycle 72 83 % 2.2MHz (LT3519-2) 3
Switch Current Limit 750 980 1150 mA 3
Switch VCESAT VCESAT 300 mV ISW = 500mA 3
Switch Leakage Current 2 μA SW = 45V, PWM = 0V 3
CTRL for Full-Scale LED Current 1.2 V 3
CTRL Pin Bias Current 50 100 nA Current Out of Pin, CTRL = 0.1V 3
PWM Input High Voltage 1.5 V 3
PWM Input Low Voltage 0.8 V 3
PWM Pin Resistance to GND 70 kΩ 3
FB Regulation Voltage VFB 1.19 1.22 1.25 V 3
FB Pin Bias Current 60 120 nA Current Out of Pin, FB = 1V 3
ISP, ISN Idle Input Bias Current 1 μA PWM = 0V, ISP = ISN = 24V 3
ISP, ISN Active Input Bias Current 17 μA ISP = ISN = 24V, Current per Pin 3
Schottky Forward Drop 0.8 V ISCHOTTKY = 500mA 3
Schottky Leakage Current 4 μA CATHODE = 24V, ANODE = 0V 3
SHDN/UVLO Threshold Voltage Falling 1.18 1.22 1.27 V 3
SHDN/UVLO Input Low Voltage 0.4 V IVIN Drops Below 1μA 3
SHDN/UVLO Pin Bias Current Low 1.8 2.2 2.6 μA SHDN/UVLO = 1.15V 3
SHDN/UVLO Pin Bias Current High 10 100 nA SHDN/UVLO = 1.30V 3
VREF Output Voltage 1.96 2 2.04 V -100μA ≤ IVREF ≤ 0μA 3
VREF Output Pin Regulation 0.04 %/V 3V < VIN < 40V 3
OPENLED Output Low VOL 240 mV IOPENLED = 1mA 3
OPENLED Leakage Current 1 μA FB = 0V, OPENLED = 40V 3
VIN, OPENLED Voltage VIN, OPENLED 40 V Note 3 2
SHDN/UVLO Voltage 40 V Note 4 2
SW, ISP, ISN, ANODE, CATHODE Voltage 45 V 2
PWM, CTRL Voltage 10 V 2
FB, VREF Voltage 3 V 2
Operating Junction Temperature Range -40 125 °C Note 2 2
Maximum Junction Temperature TJMAX 125 °C 2
Storage Temperature Range -65 125 °C 2
Thermal Resistance Junction to Ambient θJA 130 °C/W 16-Lead MSOP 2

CAD (KiCad official)

  • Symbol: LT3519EMS-2#PBF
  • Footprint: Package_SO:MSOP-16_3x4.039mm_P0.5mm
  • 3D model: MSOP-16 (KiCad packages3D, STEP)
  • 3D model files: lt3519ems-2-pbf-etched.step / lt3519ems-2-pbf-etched.glb carry the MPN laser-etched on the die in a toggleable Adom.LaserEtch group (Fusion-ready); lt3519ems-2-pbf.step / lt3519ems-2-pbf.glb are the bare package body.

Provenance

Data extracted from the manufacturer datasheet, not a distributor listing:

  • Datasheet: Analog Devices datasheet (20 pp, sha256 887e794b2bd96a8f, retrieved 2026-10-30, tier: manufacturer)
  • Extractor: parts-factory 2.0.0 / extract_pins 0.3, primary claude-sonnet-5-5 (text), consensus claude-sonnet-5-5 (agreed), guards: pin_guards 0.1: passed. Pins are checked against the footprint pad set and their cited datasheet pages before publish.
  • CAD: KiCad official libraries (CC-BY-SA 4.0).

Datasheet PDF