main
Download ZIP Propose a change
Generated by kicad-footprint-generator · KiCad file format 20260206
Name Last commit message Last updated
docs Publish 0.1.0 · Ray
viewers lt3508euf-pbf: viewers · Ray
lt3508euf-pbf-etched.glb Publish 0.1.0 · Ray
lt3508euf-pbf-etched.step lt3508euf-pbf: factory component page (tier=mfr) · Ray
lt3508euf-pbf-hero.glb lt3508euf-pbf: hero GLB from the etched model (keeps the MPN mark) · Ray
lt3508euf-pbf-hero.overlay.json Publish 0.1.0 · Ray
lt3508euf-pbf.glb Publish 0.1.0 · Ray
lt3508euf-pbf.kicad_mod Publish 0.1.0 · Ray
lt3508euf-pbf.kicad_sym Publish 0.1.0 · Ray
lt3508euf-pbf.lbr Publish 0.1.0 · Ray
lt3508euf-pbf.step Publish 0.1.0 · Ray
package.json Publish 0.1.0 · Ray
page.json Set visibility: public · Ray
README.md Publish 0.1.0 · Ray

LT3508EUF#PBF

Analog Devices · DC-DC Converters · QFN-24-EP(4x4)

LT3508EUF#PBF from Analog Devices, in a QFN-24-EP(4x4). Pinout and pin descriptions extracted from the manufacturer datasheet (extract_pins, cross-checked by a second model); symbol, footprint, and 3D from KiCad-official CAD.

Pinout

Pin Name Type Function
1 FB1 input Channel 1 feedback pin regulated to 0.800V; connect the feedback resistor divider tap here.
2 TRACK/SS1 input Channel 1 soft-start/tracking input with 1.2µA internal soft-start current charging a capacitor, or a resistor divider from a tracked output.
3 GND power_in Ground pin; tie directly to the exposed pad and ground plane.
4 GND power_in Ground pin; tie directly to the exposed pad and ground plane.
5 GND power_in Ground pin; tie directly to the exposed pad and ground plane.
6 GND power_in Ground pin; tie directly to the exposed pad and ground plane.
7 BOOST1 power_in Channel 1 boost drive supply for the internal NPN switch, higher than the input voltage; tie through a diode to a 2.8V or higher supply, max 60V and 30V above SW.
8 SW1 output Channel 1 internal power switch output; connect to the inductor, catch diode and boost capacitor.
9 VIN1 power_in Supplies internal circuitry and the channel 1 power switch, must be locally bypassed and be greater than 3.7V for either channel to operate.
10 VIN2 power_in Supplies the channel 2 power switch, must be locally bypassed and be greater than 3V (with VIN1 above 3.7V); connect to VIN1 unless powered from a different source.
11 SW2 output Channel 2 internal power switch output; connect to the inductor, catch diode and boost capacitor.
12 BOOST2 power_in Channel 2 boost drive supply for the internal NPN switch, higher than the input voltage; tie through a diode to a 2.8V or higher supply, max 60V and 30V above SW.
13 GND power_in Ground pin; tie directly to the exposed pad and ground plane.
14 GND power_in Ground pin; tie directly to the exposed pad and ground plane.
15 GND power_in Ground pin; tie directly to the exposed pad and ground plane.
16 GND power_in Ground pin; tie directly to the exposed pad and ground plane.
17 TRACK/SS2 input Channel 2 soft-start/tracking input with 1.2µA internal soft-start current charging a capacitor, or a resistor divider from a tracked output.
18 FB2 input Channel 2 feedback pin regulated to 0.800V; connect the feedback resistor divider tap here.
19 VC2 bidirectional Channel 2 error amplifier output that sets peak switch current and is used for loop compensation; pull to ground with an open drain to shut down channel 2.
20 PG2 output Channel 2 open-collector power good output that stays low until FB is within 10% of final regulation; valid when VIN1 is above 3.7V and SHDN is high, may be left unconnected.
21 SHDN input Shutdown pin: below 0.3V shuts down the part, 2.63V threshold acts as accurate UVLO, and it must not be driven more than 6V above VIN1.
22 RT/SYNC input Sets the oscillator frequency with a resistor to GND (33.2k for 1MHz) or accepts a logic-level sync signal with pulse widths of at least 80ns.
23 PG1 output Channel 1 open-collector power good output that stays low until FB is within 10% of final regulation; valid when VIN1 is above 3.7V and SHDN is high, may be left unconnected.
24 VC1 bidirectional Channel 1 error amplifier output that sets peak switch current and is used for loop compensation; pull to ground with an open drain to shut down channel 1.
25 GND power_in Exposed pad is ground and thermal contact to the PCB and must be soldered to the circuit board for proper operation.

Key specifications

Parameter Value
Manufacturer Analog Devices
Package QFN-24-EP(4x4)
Category Power Supply Chip
Pins 25

Electrical characteristics

Limits as printed in the datasheet (page.json metadata.characteristics carries them as data).

Parameter Symbol Min Typ Max Unit Conditions Page
VIN Pin Voltage -0.3 40 V 2
BOOST Pin Voltage 60 V 2
SHDN, PG Voltage 40 V 2
TRACK/SS, FB, RT/SYNC, VC Voltage 6 V 2
Storage Temperature Range (QFN) -65 150 °C QFN package 2
Operating Junction Temperature Range -40 125 °C LT3508E (Note 2) 2
Minimum Operating Voltage, VIN1 3.4 3.7 V Full operating temperature range (l) 3
Minimum Operating Voltage, VIN2 2.5 3 V VIN1 = 12V; full operating temperature range (l) 3
VIN1 Quiescent Current 4.3 5.2 mA Not switching 3
VIN2 Quiescent Current 320 500 μA Not switching 3
Shutdown Current (VIN1 + VIN2) 0.1 2 μA VSHDN = 0.3V 3
FB Voltage 0.784 0.816 V Full operating temperature range (l) 3
FB Voltage 0.79 0.8 0.814 V TA = 25°C 3
FB Pin Bias Current 50 300 nA VFB = 0.800V, VC = 0.5V; full operating temperature range (l) 3
Switching Frequency 0.92 1 1.06 MHz RT = 33.2k; full operating temperature range (l) 3
Switching Phase 150 180 210 Deg RT = 33.2k 3
Maximum Duty Cycle 84 90 % RT = 33.2k; full operating temperature range (l); Note 4 3
Maximum Duty Cycle 80 % RT = 7.50k; Note 4 3
Maximum Duty Cycle 98 % RT = 169k; Note 4 3
Switch Current Limit 2 2.6 3.2 A Duty Cycle = 15%; full operating temperature range (l) 3
Switch VCESAT 300 mV ISW = 1.5A 3
Switch Leakage Current 0.01 1 μA 3
Minimum Boost Voltage 1.7 2.5 V 3
Boost Pin Current 35 50 mA ISW = 1.5A, VBOOST = 17V 3
TRACK/SS Pin Current 0.8 1.2 2.2 μA VTRACK/SS = 0V 3
PG Threshold Offset 56 75 110 mV VFB Rising 3
PG Voltage Output Low 0.13 0.4 V VFB = 0.6V, IPG = 250μA 3
PG Pin Leakage 0.01 1 μA VPG = 2V 3
SHDN Threshold Voltage 2.53 2.63 2.73 V 3
SHDN Input Current 6 8 10 μA VSHDN = 60mV Above Threshold Voltage 3
SHDN Threshold Current Hysteresis 5.5 7.5 9.5 μA 3
SYNC Threshold Voltage 1 1.25 1.5 V 3
SYNC Input Frequency 0.25 2.5 MHz 3
Thermal Resistance, Junction-to-Ambient (θJA) θJA 40 °C/W Printed for the 24-lead 4mm × 4mm QFN (UF) package 2
Thermal Resistance, Junction-to-Case (θJC) θJC 10 °C/W Printed for the 24-lead 4mm × 4mm QFN (UF) package 2

CAD (KiCad official)

  • Symbol: LT3508EUF#PBF
  • Footprint: Package_DFN_QFN:QFN-24-1EP_4x4mm_P0.5mm_EP2.6x2.6mm
  • 3D model: QFN-24-EP(4x4) (KiCad packages3D, STEP)
  • 3D model files: lt3508euf-pbf-etched.step / lt3508euf-pbf-etched.glb carry the MPN laser-etched on the die in a toggleable Adom.LaserEtch group (Fusion-ready); lt3508euf-pbf.step / lt3508euf-pbf.glb are the bare package body.

Provenance

Data extracted from the manufacturer datasheet, not a distributor listing:

  • Datasheet: Analog Devices datasheet (26 pp, sha256 a86fb7df90de95ef, retrieved 2026-10-28, tier: manufacturer)
  • Extractor: parts-factory 2.0.0 / extract_pins 0.3, primary claude-haiku-5-5 (text), consensus claude-sonnet-5-5 (agreed), guards: pin_guards 0.1: passed. Pins are checked against the footprint pad set and their cited datasheet pages before publish.
  • CAD: KiCad official libraries (CC-BY-SA 4.0).

Datasheet PDF