Generated by kicad-footprint-generator · KiCad file format 20260206
LT3502AEMS#PBF
Analog Devices · DC-DC Converters · MSOP-10
LT3502AEMS#PBF from Analog Devices, in a MSOP-10. Pinout and pin descriptions extracted from the manufacturer datasheet (extract_pins, cross-checked by a second model); symbol, footprint, and 3D from KiCad-official CAD.
Pinout
| Pin | Name | Type | Function |
|---|---|---|---|
| 1 | SW | output | SW is the output of the internal power switch and connects to the inductor, catch diode and boost capacitor. |
| 2 | BOOST | power_out | BOOST supplies a drive voltage higher than VIN to the internal NPN power switch, with a boost capacitor connected from this pin to SW; the datasheet limits BOOST to 50V absolute maximum and 7V above the SW pin. |
| 3 | NC | unconnected | No-connect pin; the datasheet marks it NC and gives no function or electrical limit for it. |
| 4 | DA | input | DA connects to the anode of the catch diode (D1) and provides frequency foldback in extreme situations; DA pin current to stop the oscillator is 500mA minimum and 650mA typical. |
| 5 | GND | power_in | Ground pin for the regulator. |
| 6 | SHDN | input | SHDN shuts the device down when tied to ground, must be tied to 2V or more for normal operation, must not be higher than VIN, and has a 40V absolute maximum rating; it also provides soft-start and frequency foldback. |
| 7 | FB | input | FB is regulated to 0.8V and receives the feedback divider tap, with VOUT = 0.8 × (1 + R1/R2) and a recommended R2 of 10kΩ; the absolute maximum FB voltage is 6V. |
| 8 | BD | power_in | BD supplies current to the internal boost Schottky diode, with an absolute maximum BD voltage of 7V. |
| 9 | NC | unconnected | No-connect pin; the datasheet marks it NC and gives no function or electrical limit for it. |
| 10 | VIN | power_in | VIN supplies current to the internal regulator and power switch and must be locally bypassed; the absolute maximum input voltage is 40V. |
Key specifications
| Parameter | Value |
|---|---|
| Manufacturer | Analog Devices |
| Package | MSOP-10 |
| Category | Power Supply Chip |
| Pins | 10 |
Electrical characteristics
Limits as printed in the datasheet (page.json metadata.characteristics carries them as data).
| Parameter | Symbol | Min | Typ | Max | Unit | Conditions | Page |
|---|---|---|---|---|---|---|---|
| Undervoltage Lockout | 2.6 | 2.8 | 3 | V | 3 | ||
| Quiescent Current at Shutdown | 0.5 | 2 | µA | VSHDN = 0V | 3 | ||
| Quiescent Current Not Switching | 1.5 | 2 | mA | 3 | |||
| Feedback Voltage (MS10, full temperature range) | 0.78 | 0.8 | 0.816 | V | MS10 package, l (full operating temperature range) | 3 | |
| Feedback Voltage (MS10, TA = 25°C) | 0.786 | 0.8 | 0.813 | V | MS10 package, TA = 25°C | 3 | |
| FB Pin Bias Current | 15 | 50 | nA | l (full operating temperature range); Note 5: current flows out of pin | 3 | ||
| Switching Frequency (LT3502A) | 1.9 | 2.25 | 2.7 | MHz | IDA < 500mA (LT3502A), l | 3 | |
| Switching Frequency (LT3502A), second row | 1.8 | 2.25 | 2.8 | MHz | IDA < 500mA (LT3502A), l | 3 | |
| Maximum Duty Cycle | 70 | 80 | % | 100mA Load (LT3502A) | 3 | ||
| Switch Current Limit | 0.75 | 0.9 | 1.1 | A | Note 3: guaranteed by design and/or correlation to static test | 3 | |
| DA Pin Current to Stop OSC | 500 | 650 | mA | 3 | |||
| Switch Active Current | 95 | 130 | µA | SW = 10V (Note 4: current flows into pin) | 3 | ||
| Switch Active Current | 8 | 30 | µA | SW = 0V (Note 5: current flows out of pin) | 3 | ||
| BOOST Pin Current | 10 | 13 | mA | ISW = 500mA | 3 | ||
| Minimum BOOST Voltage Above Switch | 1.9 | 2.2 | V | ISW = 500mA | 3 | ||
| BOOST Schottky Forward Drop | 0.8 | 1 | V | IOUT = 100mA | 3 | ||
| SHDN Bias Current | 55 | 80 | µA | VSHDN = 5V | 3 | ||
| SHDN Bias Current | 1 | µA | VSHDN = 0V | 3 | |||
| SHDN Input Voltage High | 2 | V | 3 | ||||
| SHDN Input Voltage Low | 0.3 | V | 3 | ||||
| Switch VCESAT | 450 | mV | ISW = 500mA | 3 | |||
| Input Voltage (VIN) | 40 | V | 2 | ||||
| BOOST Voltage | 50 | V | 2 | ||||
| BOOST Pin Above SW Pin | 7 | V | 2 | ||||
| FB Voltage | 6 | V | 2 | ||||
| SHDN Voltage | 40 | V | 2 | ||||
| BD Voltage | 7 | V | 2 | ||||
| Storage Temperature Range | -65 | 150 | °C | 2 | |||
| Operating Junction Temperature Range | -40 | 125 | °C | LT3502AE (Note 2) | 2 | ||
| Input Voltage Operating Range | 3 | 40 | V | Stated as wide input voltage range in features/description | 1 | ||
| Thermal Resistance Junction-to-Ambient (MS package) | θJA | 110 | °C/W | 10-lead plastic MSOP (MS package) | 2 |
CAD (KiCad official)
- Symbol:
LT3502AEMS#PBF - Footprint:
Package_SO:MSOP-10_3x3mm_P0.5mm - 3D model: MSOP-10 (KiCad packages3D, STEP)
- 3D model files:
lt3502aems-pbf-etched.step/lt3502aems-pbf-etched.glbcarry the MPN laser-etched on the die in a toggleableAdom.LaserEtchgroup (Fusion-ready);lt3502aems-pbf.step/lt3502aems-pbf.glbare the bare package body.
Provenance
Data extracted from the manufacturer datasheet, not a distributor listing:
- Datasheet: Analog Devices datasheet (24 pp, sha256
ee1026fdeba3ecdd, retrieved 2026-10-29, tier: manufacturer) - Extractor: parts-factory
2.0.0/extract_pins 0.3, primaryclaude-haiku-5-5(text), consensusclaude-sonnet-5-5(agreed), guards: pin_guards 0.1: passed. Pins are checked against the footprint pad set and their cited datasheet pages before publish. - CAD: KiCad official libraries (CC-BY-SA 4.0).