main
Ray Publish 0.1.0 5f90c97

LT3481EDD#TRPBF

Analog Devices · DC-DC Converters · DFN-10-EP(3x3)

LT3481EDD#TRPBF from Analog Devices, in a DFN-10-EP(3x3). Pinout and pin descriptions extracted from the manufacturer datasheet (extract_pins, cross-checked by a second model); symbol, footprint, and 3D from KiCad-official CAD.

Pinout

Pin Name Type Function
1 BD passive BD pin connects to the anode of the boost Schottky diode, and the BD, BIAS and PG pins are rated to 30V.
2 BOOST passive BOOST pin provides a drive voltage higher than the input voltage to the internal NPN power switch, and BOOST pin voltage is rated to 56V with BOOST above SW limited to 30V.
3 SW output SW pin is the output of the internal power switch and connects to the inductor, catch diode and boost capacitor.
4 VIN power_in VIN pin supplies the internal regulator and power switch, must be locally bypassed, and is rated 3.6V to 34V operating with 36V maximum.
5 RUN/SS input RUN/SS pin shuts down the part when tied to ground, requires 2.3V or more for normal operation, and sets the soft-start ramp through an external RC.
6 PG output PG pin is an open-collector power good output that stays low until FB is within 10% of the final regulation voltage, and is valid when VIN is above 3.5V and RUN/SS is high.
7 BIAS power_in BIAS pin supplies the internal regulator from the lowest available source above 3V, typically VOUT, to improve efficiency.
8 FB input FB pin is regulated to 1.265V and receives the tap of the feedback resistor divider.
9 VC passive VC pin is the error amplifier output that sets peak switch current and is compensated by an RC network to ground.
10 RT passive RT pin is the oscillator resistor input, where a resistor to ground sets the switching frequency between 300kHz and 2.8MHz.
11 GND power_in Exposed pad (pin 11) is ground and must be soldered to the PCB and connected to GND.

Key specifications

Parameter Value
Manufacturer Analog Devices
Package DFN-10-EP(3x3)
Category Power Supply Chip
Pins 11

Electrical characteristics

Limits as printed in the datasheet (page.json metadata.characteristics carries them as data).

Parameter Symbol Min Typ Max Unit Conditions Page
Minimum Input Voltage 3 3.6 V ● 3
Quiescent Current from VIN 0.01 0.5 μA VRUN/SS = 0.2V 3
Quiescent Current from VIN 22 60 μA VBIAS = 3V, Not Switching ● 3
Quiescent Current from VIN 75 120 μA VBIAS = 0, Not Switching 3
Quiescent Current from BIAS 0.01 0.5 μA VRUN/SS = 0.2V 3
Quiescent Current from BIAS 50 120 μA VBIAS = 3V, Not Switching ● 3
Minimum Bias Voltage 2.7 3 V 3
Feedback Voltage 1.25 1.265 1.29 V ● 3
Feedback Voltage 1.24 1.265 1.3 V ● 3
FB Pin Bias Current 30 100 nA VFB = 1.25V, VC = 0.4V ● 3
FB Voltage Line Regulation 0.002 0.02 %/V 4V < VIN < 34V 3
Switching Frequency 2.5 2.8 3.1 MHz RT = 8.66k 3
Switching Frequency 1.25 1.4 1.55 MHz RT = 29.4k 3
Switching Frequency 250 300 350 kHz RT = 187k 3
Minimum Switch Off-Time 130 200 nS ● 3
Switch Current Limit 3.2 3.8 4.4 A Duty Cycle = 5% 3
Switch VCESAT 360 mV ISW = 2A 3
Boost Schottky Reverse Leakage 0.02 2 μA VSW = 10V, VBIAS = 0V 3
Minimum Boost Voltage 1.5 2.1 V Note 4 ● 3
BOOST Pin Current 18 35 mA ISW = 1A 3
RUN/SS Pin Current 5 10 μA VRUN/SS = 2.5V 3
RUN/SS Input Voltage High 2.5 V 3
RUN/SS Input Voltage Low 0.2 V 3
PG Threshold Offset from Feedback Voltage 122 mV VFB Rising 3
PG Hysteresis 5 mV 3
PG Leakage 0.1 1 μA VPG = 5V 3
PG Sink Current 100 600 μA VPG = 3V ● 3
BOOST Pin Above SW Pin 30 V 2
FB, RT, VC Voltage 5 V 2
BIAS, PG, BD Voltage 30 V 2
Maximum Junction Temperature (LT3481E, LT3481I) 125 °C 2
Operating Temperature Range (LT3481E) -40 85 °C 2
Storage Temperature Range -65 150 °C 2
Thermal Resistance Junction-to-Ambient (DD package) θJA 43 °C/W 2

CAD (KiCad official)

  • Symbol: LT3481EDD#TRPBF
  • Footprint: Package_DFN_QFN:DFN-10-1EP_3x3mm_P0.5mm_EP1.55x2.48mm
  • 3D model: DFN-10-EP(3x3) (KiCad packages3D, STEP)
  • 3D model files: lt3481edd-trpbf-etched.step / lt3481edd-trpbf-etched.glb carry the MPN laser-etched on the die in a toggleable Adom.LaserEtch group (Fusion-ready); lt3481edd-trpbf.step / lt3481edd-trpbf.glb are the bare package body.

Provenance

Data extracted from the manufacturer datasheet, not a distributor listing:

  • Datasheet: Analog Devices datasheet (24 pp, sha256 10dc0fc8e1493dbf, retrieved 2026-11-02, tier: manufacturer)
  • Extractor: parts-factory 2.0.0 / extract_pins 0.3, primary claude-haiku-5-5 (text), consensus claude-sonnet-5-5 (agreed), guards: pin_guards 0.1: passed. Pins are checked against the footprint pad set and their cited datasheet pages before publish.
  • CAD: KiCad official libraries (CC-BY-SA 4.0).

Datasheet PDF