Made with KiCad 10.0 · needs KiCad 10.0 or later to open · KiCad file format 20260206
LT3481EDD#TRPBF
Analog Devices · DC-DC Converters · DFN-10-EP(3x3)
LT3481EDD#TRPBF from Analog Devices, in a DFN-10-EP(3x3). Pinout and pin descriptions extracted from the manufacturer datasheet (extract_pins, cross-checked by a second model); symbol, footprint, and 3D from KiCad-official CAD.
Pinout
| Pin | Name | Type | Function |
|---|---|---|---|
| 1 | BD | passive | BD pin connects to the anode of the boost Schottky diode, and the BD, BIAS and PG pins are rated to 30V. |
| 2 | BOOST | passive | BOOST pin provides a drive voltage higher than the input voltage to the internal NPN power switch, and BOOST pin voltage is rated to 56V with BOOST above SW limited to 30V. |
| 3 | SW | output | SW pin is the output of the internal power switch and connects to the inductor, catch diode and boost capacitor. |
| 4 | VIN | power_in | VIN pin supplies the internal regulator and power switch, must be locally bypassed, and is rated 3.6V to 34V operating with 36V maximum. |
| 5 | RUN/SS | input | RUN/SS pin shuts down the part when tied to ground, requires 2.3V or more for normal operation, and sets the soft-start ramp through an external RC. |
| 6 | PG | output | PG pin is an open-collector power good output that stays low until FB is within 10% of the final regulation voltage, and is valid when VIN is above 3.5V and RUN/SS is high. |
| 7 | BIAS | power_in | BIAS pin supplies the internal regulator from the lowest available source above 3V, typically VOUT, to improve efficiency. |
| 8 | FB | input | FB pin is regulated to 1.265V and receives the tap of the feedback resistor divider. |
| 9 | VC | passive | VC pin is the error amplifier output that sets peak switch current and is compensated by an RC network to ground. |
| 10 | RT | passive | RT pin is the oscillator resistor input, where a resistor to ground sets the switching frequency between 300kHz and 2.8MHz. |
| 11 | GND | power_in | Exposed pad (pin 11) is ground and must be soldered to the PCB and connected to GND. |
Key specifications
| Parameter | Value |
|---|---|
| Manufacturer | Analog Devices |
| Package | DFN-10-EP(3x3) |
| Category | Power Supply Chip |
| Pins | 11 |
Electrical characteristics
Limits as printed in the datasheet (page.json metadata.characteristics carries them as data).
| Parameter | Symbol | Min | Typ | Max | Unit | Conditions | Page |
|---|---|---|---|---|---|---|---|
| Minimum Input Voltage | 3 | 3.6 | V | ● | 3 | ||
| Quiescent Current from VIN | 0.01 | 0.5 | μA | VRUN/SS = 0.2V | 3 | ||
| Quiescent Current from VIN | 22 | 60 | μA | VBIAS = 3V, Not Switching ● | 3 | ||
| Quiescent Current from VIN | 75 | 120 | μA | VBIAS = 0, Not Switching | 3 | ||
| Quiescent Current from BIAS | 0.01 | 0.5 | μA | VRUN/SS = 0.2V | 3 | ||
| Quiescent Current from BIAS | 50 | 120 | μA | VBIAS = 3V, Not Switching ● | 3 | ||
| Minimum Bias Voltage | 2.7 | 3 | V | 3 | |||
| Feedback Voltage | 1.25 | 1.265 | 1.29 | V | ● | 3 | |
| Feedback Voltage | 1.24 | 1.265 | 1.3 | V | ● | 3 | |
| FB Pin Bias Current | 30 | 100 | nA | VFB = 1.25V, VC = 0.4V ● | 3 | ||
| FB Voltage Line Regulation | 0.002 | 0.02 | %/V | 4V < VIN < 34V | 3 | ||
| Switching Frequency | 2.5 | 2.8 | 3.1 | MHz | RT = 8.66k | 3 | |
| Switching Frequency | 1.25 | 1.4 | 1.55 | MHz | RT = 29.4k | 3 | |
| Switching Frequency | 250 | 300 | 350 | kHz | RT = 187k | 3 | |
| Minimum Switch Off-Time | 130 | 200 | nS | ● | 3 | ||
| Switch Current Limit | 3.2 | 3.8 | 4.4 | A | Duty Cycle = 5% | 3 | |
| Switch VCESAT | 360 | mV | ISW = 2A | 3 | |||
| Boost Schottky Reverse Leakage | 0.02 | 2 | μA | VSW = 10V, VBIAS = 0V | 3 | ||
| Minimum Boost Voltage | 1.5 | 2.1 | V | Note 4 ● | 3 | ||
| BOOST Pin Current | 18 | 35 | mA | ISW = 1A | 3 | ||
| RUN/SS Pin Current | 5 | 10 | μA | VRUN/SS = 2.5V | 3 | ||
| RUN/SS Input Voltage High | 2.5 | V | 3 | ||||
| RUN/SS Input Voltage Low | 0.2 | V | 3 | ||||
| PG Threshold Offset from Feedback Voltage | 122 | mV | VFB Rising | 3 | |||
| PG Hysteresis | 5 | mV | 3 | ||||
| PG Leakage | 0.1 | 1 | μA | VPG = 5V | 3 | ||
| PG Sink Current | 100 | 600 | μA | VPG = 3V ● | 3 | ||
| BOOST Pin Above SW Pin | 30 | V | 2 | ||||
| FB, RT, VC Voltage | 5 | V | 2 | ||||
| BIAS, PG, BD Voltage | 30 | V | 2 | ||||
| Maximum Junction Temperature (LT3481E, LT3481I) | 125 | °C | 2 | ||||
| Operating Temperature Range (LT3481E) | -40 | 85 | °C | 2 | |||
| Storage Temperature Range | -65 | 150 | °C | 2 | |||
| Thermal Resistance Junction-to-Ambient (DD package) | θJA | 43 | °C/W | 2 |
CAD (KiCad official)
- Symbol:
LT3481EDD#TRPBF - Footprint:
Package_DFN_QFN:DFN-10-1EP_3x3mm_P0.5mm_EP1.55x2.48mm - 3D model: DFN-10-EP(3x3) (KiCad packages3D, STEP)
- 3D model files:
lt3481edd-trpbf-etched.step/lt3481edd-trpbf-etched.glbcarry the MPN laser-etched on the die in a toggleableAdom.LaserEtchgroup (Fusion-ready);lt3481edd-trpbf.step/lt3481edd-trpbf.glbare the bare package body.
Provenance
Data extracted from the manufacturer datasheet, not a distributor listing:
- Datasheet: Analog Devices datasheet (24 pp, sha256
10dc0fc8e1493dbf, retrieved 2026-11-02, tier: manufacturer) - Extractor: parts-factory
2.0.0/extract_pins 0.3, primaryclaude-haiku-5-5(text), consensusclaude-sonnet-5-5(agreed), guards: pin_guards 0.1: passed. Pins are checked against the footprint pad set and their cited datasheet pages before publish. - CAD: KiCad official libraries (CC-BY-SA 4.0).