main
History Download
Ray Publish 0.1.0 dfd28e6

LT3474EFE#PBF

Analog Devices · LED Drivers · TSSOP-16-EP

LT3474EFE#PBF from Analog Devices, in a TSSOP-16-EP. Pinout and pin descriptions extracted from the manufacturer datasheet (extract_pins, cross-checked by a second model); symbol, footprint, and 3D from KiCad-official CAD.

Pinout

Pin Name Type Function
1 DNC unconnected Do not connect external circuitry to this pin, or tie it to GND; leave the DNC pin floating.
2 OUT input Input to the internal current sense resistor; connect to the inductor and the output capacitor (absolute maximum 15V for LT3474, 26V for LT3474-1).
3 LED output Output of the current sense resistor; connect the anode of the LED here (absolute maximum 15V for LT3474, 26V for LT3474-1).
4 VIN power_in Supplies current to the internal circuitry and internal power switch and must be locally bypassed; input range 4V to 36V.
5 SW output Output of the internal power switch; connect to the inductor and switching diode.
6 BOOST power_in Provides a drive voltage, higher than the input voltage, to the internal bipolar NPN power switch (absolute maximum 51V).
7 BIAS power_in Connects through a Schottky diode to BOOST; tie to OUT (absolute maximum 25V).
8 GND power_in Ground; tie directly to the ground plane.
9 RT passive Sets the internal oscillator frequency; an 80.6k resistor from RT to GND gives 500kHz switching frequency.
10 SHDN input Shuts down the regulator when pulled below 0.3V and enables it above 2.65V, with a 2.6V accurate threshold usable as undervoltage lockout; tie to VIN if unused.
11 REF output Buffered output of the internal reference (1.25V typical); tie to VADJ for 1A output current or use a divider, leave unconnected if unused.
12 VC passive Output of the internal error amplifier whose voltage controls the peak switch current; use it to compensate the control loop.
13 VADJ input Input to the internal voltage to current amplifier; connect to REF for 1A output current, or program lower currents with ILED = 1A • VADJ/1.25V.
14 PWM input Controls the connection of the VC pin to internal circuitry; when low VC is disconnected and draws minimal current, leave unconnected if PWM feature is unused.
15 GND power_in Ground; tie directly to the ground plane.
16 DNC unconnected Do not connect external circuitry to this pin, or tie it to GND; leave the DNC pin floating.
17 GND power_in Exposed pad is ground, providing electrical and thermal contact to the PCB; it must be soldered to the circuit board for proper operation.

Key specifications

Parameter Value
Manufacturer Analog Devices
Package TSSOP-16-EP
Category Display Modules / LED Drivers / Display Drivers
Pins 17

Electrical characteristics

Limits as printed in the datasheet (page.json metadata.characteristics carries them as data).

Parameter Symbol Min Typ Max Unit Conditions Page
Minimum Input Voltage 3.5 4 V full temperature range 2
Input Quiescent Current 2.6 4 mA Not Switching 2
Shutdown Current 0.01 2 µA SHDN = 0.3V, VBOOST = 0V, VOUT = 0V 2
LED Pin Current (VADJ tied to VREF) 0.98 1 1.02 A VADJ Tied to VREF, full temperature range 2
LED Pin Current (VADJ tied to VREF/5) 0.193 0.2 0.207 A VADJ Tied to VREF/5, full temperature range 2
REF Voltage 1.23 1.25 1.265 V full temperature range 2
Reference Voltage Line Regulation 0.01 %/V 5V < VIN < 36V 3
Reference Voltage Load Regulation 0.0002 %/µA 0 < IREF < 250µA 3
VADJ Pin Bias Current 20 400 nA Note 4, full temperature range 3
Switching Frequency 470 500 530 kHz RT = 80.6k 3
Switching Frequency (full temp) 450 540 kHz RT = 80.6k, full temperature range 3
Maximum Duty Cycle 90 95 % RT = 80.6k, full temperature range 3
Maximum Duty Cycle 76 % RT = 10k 3
Maximum Duty Cycle 98 % RT = 232k 3
Foldback Frequency 70 kHz RT = 80.6k, VOUT = 0V 3
SHDN Threshold (to Switch) 2.6 2.65 2.7 V 3
SHDN Pin Current 8.3 10.3 12.3 µA VSHDN = SHDN Threshold (Note 5) 3
PWM Threshold 0.4 0.9 1.2 V 3
VC Switching Threshold 0.8 V 3
VC Source Current 100 µA VC = 1V 3
VC Sink Current 100 µA VC = 1V 3
LED to VC Current Gain 1.5 µA/mA 3
LED to VC Transresistance 1 V/mA 3
VC to Switch Current Gain 2 A/V 3
VC Clamp Voltage 1.9 V 3
VC Pin Current in PWM Mode 0.01 1 µA VC = 1V, VPWM = 0.3V, full temperature range 3
OUT Pin Clamp Voltage (LT3474) 13.2 13.8 14.5 V 3
OUT Pin Current in PWM Mode 0.1 10 µA VOUT = 4V, VPWM = 0.3V, full temperature range 3
Switch Current Limit 1.6 2.1 3.2 A -40°C to 85°C 3
Switch VCESAT 380 500 mV ISW = 1A 3
Boost Pin Current 30 50 mA ISW = 1A 3
Switch Leakage Current 0.01 1 µA 3
Minimum Boost Voltage 1.9 2.5 V Note 7 3
Boost Diode Forward Voltage 600 mV IDIO = 100mA 3
VIN Pin Voltage VIN -0.3 36 V 2
BIAS Pin Voltage 25 V 2
BOOST above SW Pin 25 V 2
OUT, LED Pins (LT3474) 15 V 2
PWM Pin Voltage 10 V 2
VADJ Pin Voltage 6 V 2
VC, REF, RT Pins 3 V 2
BIAS Pin Current 1 A 2
Maximum Junction Temperature 125 °C Note 2 2
Operating Temperature Range (LT3474E) -40 85 °C LT3474E 2
Storage Temperature Range -65 150 °C 2
Lead Temperature (Soldering, 10 sec) 300 °C 2
Thermal Resistance Junction-to-Case θJC 8 °C/W FE package 2
Thermal Resistance Junction-to-Ambient θJA 40 °C/W FE package 2

CAD (KiCad official)

  • Symbol: LT3474EFE#PBF
  • Footprint: Package_SO:TSSOP-16-1EP_4.4x5mm_P0.65mm
  • 3D model: TSSOP-16-EP (KiCad packages3D, STEP)
  • 3D model files: lt3474efe-pbf-etched.step / lt3474efe-pbf-etched.glb carry the MPN laser-etched on the die in a toggleable Adom.LaserEtch group (Fusion-ready); lt3474efe-pbf.step / lt3474efe-pbf.glb are the bare package body.

Provenance

Data extracted from the manufacturer datasheet, not a distributor listing:

  • Datasheet: Analog Devices datasheet (20 pp, sha256 40025199cda8d86e, retrieved 2026-10-31, tier: manufacturer)
  • Extractor: parts-factory 2.0.0 / extract_pins 0.3, primary claude-sonnet-5-5 (text), consensus claude-sonnet-5-5 (agreed), guards: pin_guards 0.1: passed. Pins are checked against the footprint pad set and their cited datasheet pages before publish.
  • CAD: KiCad official libraries (CC-BY-SA 4.0).

Datasheet PDF