3D Model
Open in new tab ↗
Loads when you scroll to it. Unloads after 5 minutes in the background.
Symbol & Footprint
Schematic Symbol
Open full view ↗Loads when you scroll to it. Unloads after 5 minutes in the background.
PCB Footprint
Open full view ↗Loads when you scroll to it. Unloads after 5 minutes in the background.
Datasheet
Open in new tab ↗Loads when you scroll to it. Unloads after 5 minutes in the background.
README
markdownLT3474EFE#PBF
Analog Devices · LED Drivers · TSSOP-16-EP
LT3474EFE#PBF from Analog Devices, in a TSSOP-16-EP. Pinout and pin descriptions extracted from the manufacturer datasheet (extract_pins, cross-checked by a second model); symbol, footprint, and 3D from KiCad-official CAD.
Pinout
| Pin | Name | Type | Function |
|---|---|---|---|
| 1 | DNC | unconnected | Do not connect external circuitry to this pin, or tie it to GND; leave the DNC pin floating. |
| 2 | OUT | input | Input to the internal current sense resistor; connect to the inductor and the output capacitor (absolute maximum 15V for LT3474, 26V for LT3474-1). |
| 3 | LED | output | Output of the current sense resistor; connect the anode of the LED here (absolute maximum 15V for LT3474, 26V for LT3474-1). |
| 4 | VIN | power_in | Supplies current to the internal circuitry and internal power switch and must be locally bypassed; input range 4V to 36V. |
| 5 | SW | output | Output of the internal power switch; connect to the inductor and switching diode. |
| 6 | BOOST | power_in | Provides a drive voltage, higher than the input voltage, to the internal bipolar NPN power switch (absolute maximum 51V). |
| 7 | BIAS | power_in | Connects through a Schottky diode to BOOST; tie to OUT (absolute maximum 25V). |
| 8 | GND | power_in | Ground; tie directly to the ground plane. |
| 9 | RT | passive | Sets the internal oscillator frequency; an 80.6k resistor from RT to GND gives 500kHz switching frequency. |
| 10 | SHDN | input | Shuts down the regulator when pulled below 0.3V and enables it above 2.65V, with a 2.6V accurate threshold usable as undervoltage lockout; tie to VIN if unused. |
| 11 | REF | output | Buffered output of the internal reference (1.25V typical); tie to VADJ for 1A output current or use a divider, leave unconnected if unused. |
| 12 | VC | passive | Output of the internal error amplifier whose voltage controls the peak switch current; use it to compensate the control loop. |
| 13 | VADJ | input | Input to the internal voltage to current amplifier; connect to REF for 1A output current, or program lower currents with ILED = 1A • VADJ/1.25V. |
| 14 | PWM | input | Controls the connection of the VC pin to internal circuitry; when low VC is disconnected and draws minimal current, leave unconnected if PWM feature is unused. |
| 15 | GND | power_in | Ground; tie directly to the ground plane. |
| 16 | DNC | unconnected | Do not connect external circuitry to this pin, or tie it to GND; leave the DNC pin floating. |
| 17 | GND | power_in | Exposed pad is ground, providing electrical and thermal contact to the PCB; it must be soldered to the circuit board for proper operation. |
Key specifications
| Parameter | Value |
|---|---|
| Manufacturer | Analog Devices |
| Package | TSSOP-16-EP |
| Category | Display Modules / LED Drivers / Display Drivers |
| Pins | 17 |
Electrical characteristics
Limits as printed in the datasheet (page.json metadata.characteristics carries them as data).
| Parameter | Symbol | Min | Typ | Max | Unit | Conditions | Page |
|---|---|---|---|---|---|---|---|
| Minimum Input Voltage | 3.5 | 4 | V | full temperature range | 2 | ||
| Input Quiescent Current | 2.6 | 4 | mA | Not Switching | 2 | ||
| Shutdown Current | 0.01 | 2 | µA | SHDN = 0.3V, VBOOST = 0V, VOUT = 0V | 2 | ||
| LED Pin Current (VADJ tied to VREF) | 0.98 | 1 | 1.02 | A | VADJ Tied to VREF, full temperature range | 2 | |
| LED Pin Current (VADJ tied to VREF/5) | 0.193 | 0.2 | 0.207 | A | VADJ Tied to VREF/5, full temperature range | 2 | |
| REF Voltage | 1.23 | 1.25 | 1.265 | V | full temperature range | 2 | |
| Reference Voltage Line Regulation | 0.01 | %/V | 5V < VIN < 36V | 3 | |||
| Reference Voltage Load Regulation | 0.0002 | %/µA | 0 < IREF < 250µA | 3 | |||
| VADJ Pin Bias Current | 20 | 400 | nA | Note 4, full temperature range | 3 | ||
| Switching Frequency | 470 | 500 | 530 | kHz | RT = 80.6k | 3 | |
| Switching Frequency (full temp) | 450 | 540 | kHz | RT = 80.6k, full temperature range | 3 | ||
| Maximum Duty Cycle | 90 | 95 | % | RT = 80.6k, full temperature range | 3 | ||
| Maximum Duty Cycle | 76 | % | RT = 10k | 3 | |||
| Maximum Duty Cycle | 98 | % | RT = 232k | 3 | |||
| Foldback Frequency | 70 | kHz | RT = 80.6k, VOUT = 0V | 3 | |||
| SHDN Threshold (to Switch) | 2.6 | 2.65 | 2.7 | V | 3 | ||
| SHDN Pin Current | 8.3 | 10.3 | 12.3 | µA | VSHDN = SHDN Threshold (Note 5) | 3 | |
| PWM Threshold | 0.4 | 0.9 | 1.2 | V | 3 | ||
| VC Switching Threshold | 0.8 | V | 3 | ||||
| VC Source Current | 100 | µA | VC = 1V | 3 | |||
| VC Sink Current | 100 | µA | VC = 1V | 3 | |||
| LED to VC Current Gain | 1.5 | µA/mA | 3 | ||||
| LED to VC Transresistance | 1 | V/mA | 3 | ||||
| VC to Switch Current Gain | 2 | A/V | 3 | ||||
| VC Clamp Voltage | 1.9 | V | 3 | ||||
| VC Pin Current in PWM Mode | 0.01 | 1 | µA | VC = 1V, VPWM = 0.3V, full temperature range | 3 | ||
| OUT Pin Clamp Voltage (LT3474) | 13.2 | 13.8 | 14.5 | V | 3 | ||
| OUT Pin Current in PWM Mode | 0.1 | 10 | µA | VOUT = 4V, VPWM = 0.3V, full temperature range | 3 | ||
| Switch Current Limit | 1.6 | 2.1 | 3.2 | A | -40°C to 85°C | 3 | |
| Switch VCESAT | 380 | 500 | mV | ISW = 1A | 3 | ||
| Boost Pin Current | 30 | 50 | mA | ISW = 1A | 3 | ||
| Switch Leakage Current | 0.01 | 1 | µA | 3 | |||
| Minimum Boost Voltage | 1.9 | 2.5 | V | Note 7 | 3 | ||
| Boost Diode Forward Voltage | 600 | mV | IDIO = 100mA | 3 | |||
| VIN Pin Voltage | VIN | -0.3 | 36 | V | 2 | ||
| BIAS Pin Voltage | 25 | V | 2 | ||||
| BOOST above SW Pin | 25 | V | 2 | ||||
| OUT, LED Pins (LT3474) | 15 | V | 2 | ||||
| PWM Pin Voltage | 10 | V | 2 | ||||
| VADJ Pin Voltage | 6 | V | 2 | ||||
| VC, REF, RT Pins | 3 | V | 2 | ||||
| BIAS Pin Current | 1 | A | 2 | ||||
| Maximum Junction Temperature | 125 | °C | Note 2 | 2 | |||
| Operating Temperature Range (LT3474E) | -40 | 85 | °C | LT3474E | 2 | ||
| Storage Temperature Range | -65 | 150 | °C | 2 | |||
| Lead Temperature (Soldering, 10 sec) | 300 | °C | 2 | ||||
| Thermal Resistance Junction-to-Case | θJC | 8 | °C/W | FE package | 2 | ||
| Thermal Resistance Junction-to-Ambient | θJA | 40 | °C/W | FE package | 2 |
CAD (KiCad official)
- Symbol:
LT3474EFE#PBF - Footprint:
Package_SO:TSSOP-16-1EP_4.4x5mm_P0.65mm - 3D model: TSSOP-16-EP (KiCad packages3D, STEP)
- 3D model files:
lt3474efe-pbf-etched.step/lt3474efe-pbf-etched.glbcarry the MPN laser-etched on the die in a toggleableAdom.LaserEtchgroup (Fusion-ready);lt3474efe-pbf.step/lt3474efe-pbf.glbare the bare package body.
Provenance
Data extracted from the manufacturer datasheet, not a distributor listing:
- Datasheet: Analog Devices datasheet (20 pp, sha256
40025199cda8d86e, retrieved 2026-10-31, tier: manufacturer) - Extractor: parts-factory
2.0.0/extract_pins 0.3, primaryclaude-sonnet-5-5(text), consensusclaude-sonnet-5-5(agreed), guards: pin_guards 0.1: passed. Pins are checked against the footprint pad set and their cited datasheet pages before publish. - CAD: KiCad official libraries (CC-BY-SA 4.0).