Loads when you scroll to it. Unloads after 5 minutes in the background.

Symbol & Footprint

Schematic Symbol

Open full view ↗
Loads when you scroll to it. Unloads after 5 minutes in the background.

PCB Footprint

Open full view ↗
Loads when you scroll to it. Unloads after 5 minutes in the background.
Loads when you scroll to it. Unloads after 5 minutes in the background.
Download PDF
Contents

README

markdown

LT3420EMS-1#PBF

Analog Devices · DC-DC Converters · MSOP-10

LT3420EMS-1#PBF from Analog Devices, in a MSOP-10. Pinout and pin descriptions extracted from the manufacturer datasheet (extract_pins, cross-checked by a second model); symbol, footprint, and 3D from KiCad-official CAD.

Pinout

Pin Name Type Function
1 RREF passive Reference resistor pin with a 1.00V threshold (0.98V to 1.02V), 2µA to 4µA bias current while switching, and a 2.5V absolute maximum voltage.
2 VBAT power_in Battery supply pin with a 1.6V minimum (1.8V typical) and 16V maximum operating voltage, and 275mV UVLO hysteresis.
3 RFB input Feedback pin whose bias current flows out of the pin, with an absolute maximum current rating of ±3mA.
4 VCC power_in Supply pin with a 2.2V minimum (2.5V typical) and 16V maximum operating voltage, and 40mV UVLO hysteresis.
5 GND power_in Ground reference pin for the device; the datasheet gives no electrical limit specific to this pin.
6 SW output Power switch pin rated 38V absolute maximum on the LT3420 and 50V on the LT3420-1, with switch leakage specified at 1µA maximum at those voltages.
7 SEC input Secondary-side sense pin with a ±200mA absolute maximum current rating.
8 DONE output Charge-complete output that reads 3.3V high through a 100k pull-up from VCC and 200mV maximum low when sinking 33µA, with a 16V voltage rating and ±1mA current rating.
9 CHARGE input Charge enable input with a 1.5V minimum high threshold, 0.2V maximum low threshold, and 16V absolute maximum voltage.
10 CT passive Refresh timer pin with a 1.5V absolute maximum voltage and refresh thresholds of 0.9V to 1.1V (upper) and 0.45V to 0.55V (lower).

Key specifications

Parameter Value
Manufacturer Analog Devices
Package MSOP-10
Category Power Supply Chip
Pins 10

Electrical characteristics

Limits as printed in the datasheet (page.json metadata.characteristics carries them as data).

Parameter Symbol Min Typ Max Unit Conditions Page
Minimum Operating Voltage, VCC VCC 2.2 2.5 V ● full operating temperature range 2
Maximum Operating Voltage, VCC VCC 16 V 2
Minimum VBAT Voltage VBAT 1.6 1.8 V 2
Maximum VBAT Voltage VBAT 16 V 2
RREF Threshold Voltage 0.98 1 1.02 V 2
RREF Threshold Voltage 0.975 1.025 V ● full operating temperature range 2
RREF Pin Bias Current 2 4 µA VRREF = 0V, Switching 2
Quiescent Current IQ 90 130 µA VRREF = 1.1V, Not Switching 2
Quiescent Current in Shutdown IQ 0.01 1 µA VCHARGE = 0V, VIN = 3.3V 2
Primary Side Current Limit LT3420-1 0.75 0.9 1.05 A Note 5 3
Secondary Side Current Limit LT3420-1 5 15 25 mA Note 5 3
Refresh Timer Charge/Discharge Current 1.5 2.5 3.5 µA VCT = 0.75V 3
Refresh Timer Upper Threshold 0.9 1 1.1 V 3
Refresh Timer Lower Threshold 0.45 0.5 0.55 V 3
Switch VCESAT LT3420-1 VCESAT 130 230 mV SW = 0.5A (Note 5) 3
Switch Leakage Current 0.01 1 µA VSW = 50V (LT3420-1) 3
CHARGE Input Voltage High 1.5 V 3
CHARGE Input Voltage Low 0.2 V 3
CHARGE Pin Bias Current 4.5 15 µA VCHARGE = 3V 3
CHARGE Pin Bias Current 0.01 0.1 µA VCHARGE = 0V 3
DONE Output Signal Low 100 200 mV 33µA into DONE Pin 3
VCC Voltage VCC 16 V 2
VBAT Voltage VBAT 16 V 2
SW Voltage LT3420-1 SW 50 V Note 2 2
SEC Current -200 200 mA 2
RFB Current -3 3 mA 2
RREF Voltage 2.5 V 2
CHARGE Voltage 16 V 2
CT Voltage 1.5 V 2
DONE Voltage 16 V 2
Current into DONE Pin -1 1 mA 2
Maximum Junction Temperature TJMAX 125 °C 2
Operating Ambient Temperature Range TA -40 85 °C Note 3; specifications guaranteed 0°C to 70°C 2
Storage Temperature Range TSTG -40 125 °C 2
Lead Temperature (Soldering, 10 sec) 300 °C For MS Package only 2
VCC UVLO Hysteresis 40 mV 2
VBAT UVLO Hysteresis 275 mV 2
Thermal resistance junction-to-ambient θJA 100 °C/W (4-LAYER BOARD) 2
Thermal resistance junction-to-case θJC 45 °C/W (4-LAYER BOARD) 2

CAD (KiCad official)

  • Symbol: LT3420EMS-1#PBF
  • Footprint: Package_SO:MSOP-10_3x3mm_P0.5mm
  • 3D model: MSOP-10 (KiCad packages3D, STEP)
  • 3D model files: lt3420ems-1-pbf-etched.step / lt3420ems-1-pbf-etched.glb carry the MPN laser-etched on the die in a toggleable Adom.LaserEtch group (Fusion-ready); lt3420ems-1-pbf.step / lt3420ems-1-pbf.glb are the bare package body.

Provenance

Data extracted from the manufacturer datasheet, not a distributor listing:

  • Datasheet: Analog Devices datasheet (20 pp, sha256 3e0767ae009dbdb1, retrieved 2026-10-29, tier: manufacturer)
  • Extractor: parts-factory 2.0.0 / extract_pins 0.3, primary claude-haiku-5-5 (text), consensus claude-sonnet-5-5 (agreed), guards: pin_guards 0.1: passed. Pins are checked against the footprint pad set and their cited datasheet pages before publish.
  • CAD: KiCad official libraries (CC-BY-SA 4.0).

Datasheet PDF