component
LT3061EMS8E#TRPBF
Public Made by Adomby adom
Analog Devices Linear Voltage Regulators (LDO), MSOP-8-EP. Pinout cross-checked by two models against the datasheet, KiCad symbol/footprint/3D.
3D Model
Open in new tab ↗
Loads when you scroll to it. Unloads after 5 minutes in the background.
Symbol & Footprint
Schematic Symbol
Open full view ↗Loads when you scroll to it. Unloads after 5 minutes in the background.
PCB Footprint
Open full view ↗Loads when you scroll to it. Unloads after 5 minutes in the background.
Datasheet
Open in new tab ↗Loads when you scroll to it. Unloads after 5 minutes in the background.
README
markdownLT3061EMS8E#TRPBF
Analog Devices · Linear Voltage Regulators (LDO) · MSOP-8-EP
LT3061EMS8E#TRPBF from Analog Devices, in a MSOP-8-EP. Pinout and pin descriptions extracted from the manufacturer datasheet (extract_pins, cross-checked by a second model); symbol, footprint, and 3D from KiCad-official CAD.
Pinout
| Pin | Name | Type | Function |
|---|---|---|---|
| 1 | REF/BYP | passive | A single capacitor from this pin to GND bypasses reference noise and soft-starts the reference (10nF gives 30µVRMS over 10Hz to 100kHz), the pin is actively pulled low in shutdown, must be left floating if unused, must not be driven by active circuitry, and its voltage is limited to -0.3V to 1V. |
| 2 | ADJ | input | This is the inverting input of the error amplifier, which regulates ADJ to 600mV referenced to GND, with a typical bias current of 15nA flowing out of the pin. |
| 3 | OUT | power_out | This output pin supplies load power, requires a minimum 3.3µF low-ESR ceramic output capacitor to prevent oscillation, and has an output voltage range of 600mV to 19V. |
| 4 | OUT | power_out | This output pin supplies load power, requires a minimum 3.3µF low-ESR ceramic output capacitor to prevent oscillation, and has an output voltage range of 600mV to 19V. |
| 5 | IN | power_in | This input pin supplies power to the device over a 1.6V to 45V supply range, and a 1µF to 10µF bypass capacitor is required if the device is more than six inches from the input filter capacitor. |
| 6 | IN | power_in | This input pin supplies power to the device over a 1.6V to 45V supply range, and a 1µF to 10µF bypass capacitor is required if the device is more than six inches from the input filter capacitor. |
| 7 | SHDN | input | Pulling this pin low puts the device into a low-power state and turns the output off, SHDN pin current is typically under 3µA, it must be tied to IN if unused, and it cannot be driven below GND unless tied to IN. |
| 8 | GND | power_in | Ground pin, where the bottom of the output-setting resistor divider should connect directly for optimum regulation, and which must be tied to exposed pad pin 9 and the PCB ground. |
| 9 | GND | power_in | Exposed pad, which must be tied directly to pin 8 and to the PCB ground and must be soldered to the PCB for enhanced thermal performance. |
Key specifications
| Parameter | Value |
|---|---|
| Manufacturer | Analog Devices |
| Package | MSOP-8-EP |
| Category | Power Management ICs |
| Pins | 9 |
Electrical characteristics
Limits as printed in the datasheet (page.json metadata.characteristics carries them as data).
| Parameter | Symbol | Min | Typ | Max | Unit | Conditions | Page |
|---|---|---|---|---|---|---|---|
| ADJ Pin Voltage | VADJ | 594 | 600 | 606 | mV | VIN = 2.1V, ILOAD = 1mA | 3 |
| ADJ Pin Voltage | VADJ | 588 | 600 | 612 | mV | 2.1V < VIN < 45V, 1mA < ILOAD < 100mA (E-, I-Grades); full operating temperature range | 3 |
| Current Limit | ILIM | 110 | 180 | mA | VIN = VOUT(NOMINAL) + 1V (Note 11), ΔVOUT = -5% | 4 | |
| Dropout Voltage | VDO | 250 | 290 | mV | ILOAD = 100mA | 3 | |
| Dropout Voltage | VDO | 430 | mV | ILOAD = 100mA; full operating temperature range | 3 | ||
| Dropout Voltage | VDO | 195 | 240 | mV | ILOAD = 50mA | 3 | |
| Dropout Voltage | VDO | 350 | mV | ILOAD = 50mA; full operating temperature range | 3 | ||
| Dropout Voltage | VDO | 130 | 180 | mV | ILOAD = 10mA | 3 | |
| Dropout Voltage | VDO | 270 | mV | ILOAD = 10mA; full operating temperature range | 3 | ||
| Dropout Voltage | VDO | 65 | 110 | mV | ILOAD = 1mA | 3 | |
| Dropout Voltage | VDO | 180 | mV | ILOAD = 1mA; full operating temperature range | 3 | ||
| Ripple Rejection | PSRR | 70 | 85 | dB | VIN, VOUT = 1.5V (AVG), VRIPPLE = 0.5VP-P, fRIPPLE = 120Hz, ILOAD = 200mA (LT3061, Note 4) | 4 | |
| Minimum Input Voltage | VIN(MIN) | 1.6 | 2.1 | V | ILOAD = 100mA | 3 | |
| Line Regulation | 0.5 | 4 | mV | ILOAD = 1mA; LT3061: ΔVIN = 2.1V to 45V (E-, I-Grades) | 3 | ||
| Load Regulation | 0.2 | 4 | mV | ΔILOAD = 1mA to 100mA; LT3061: VIN = 2.1V (E-, I-Grades) | 3 | ||
| GND Pin Current | IGND | 45 | 90 | µA | VIN = VOUT(NOMINAL) + 0.6V, ILOAD = 0 | 3 | |
| GND Pin Current | IGND | 70 | 120 | µA | VIN = VOUT(NOMINAL) + 0.6V, ILOAD = 1mA | 3 | |
| GND Pin Current | IGND | 225 | 500 | µA | VIN = VOUT(NOMINAL) + 0.6V, ILOAD = 10mA | 3 | |
| GND Pin Current | IGND | 0.8 | 1.8 | mA | VIN = VOUT(NOMINAL) + 0.6V, ILOAD = 50mA | 3 | |
| GND Pin Current | IGND | 2 | 4 | mA | VIN = VOUT(NOMINAL) + 0.6V, ILOAD = 100mA | 3 | |
| Quiescent Current in Shutdown | IQ(SHDN) | 1.25 | 3 | µA | VIN = 45V, VSHDN = 0V | 4 | |
| Input Reverse Leakage Current | 1 | mA | VIN = -45V, VOUT = 0 | 4 | |||
| Output Discharge Time | 0.75 | 2 | ms | VOUT discharged to 10% of Nominal, COUT = 10µF | 4 | ||
| Reverse Output Current | 2.5 | 15 | µA | VOUT = 3.3V, VIN = VSHDN = 2.1V (Note 4) | 4 | ||
| Shutdown Threshold (Off to On) | VSHDN | 0.3 | 0.8 | V | VOUT = Off to On | 4 | |
| Shutdown Threshold (On to Off) | VSHDN | 0.7 | 1.5 | V | VOUT = On to Off | 4 | |
| SHDN Pin Current | ISHDN | 1.2 | µA | VSHDN = 0V | 4 | ||
| SHDN Pin Current | ISHDN | 3 | µA | VSHDN = 45V | 4 | ||
| ADJ Pin Bias Current | IADJ | 15 | 60 | nA | 4 | ||
| Output Voltage Noise | VN | 30 | µVRMS | COUT = 10µF, ILOAD = 100mA, CREF/BYP = 0.01µF, VOUT = 600mV, BW = 10Hz to 100kHz | 4 | ||
| IN Pin Voltage | VIN | -50 | 50 | V | 2 | ||
| OUT Pin Voltage | VOUT | -1 | 20 | V | 2 | ||
| Input to Output Differential Voltage | VIN-VOUT | -50 | 50 | V | Note 2 | 2 | |
| ADJ Pin Voltage | VADJ | -50 | 50 | V | 2 | ||
| SHDN Pin Voltage | VSHDN | -50 | 50 | V | 2 | ||
| REF/BYP Pin Voltage | VREF/BYP | -0.3 | 1 | V | 2 | ||
| Operating Junction Temperature | TJ | -40 | 125 | °C | E- and I-Grades (Notes 3, 5, 12) | 2 | |
| Storage Temperature Range | TSTG | -65 | 150 | °C | 2 | ||
| Junction-to-Ambient Thermal Resistance | θJA | 29 | 45 | °C/W | MS8E (MSOP) package; range depends on board copper area (Table 3) | 2 | |
| Junction-to-Case Thermal Resistance | θJC | 5 | 10 | °C/W | MS8E (MSOP) package | 2 |
CAD (KiCad official)
- Symbol:
LT3061EMS8E#TRPBF - Footprint:
Package_SO:MSOP-8-1EP_3x3mm_P0.65mm_EP1.5x1.8mm - 3D model: MSOP-8-EP (KiCad packages3D, STEP)
- 3D model files:
lt3061ems8e-trpbf-etched.step/lt3061ems8e-trpbf-etched.glbcarry the MPN laser-etched on the die in a toggleableAdom.LaserEtchgroup (Fusion-ready);lt3061ems8e-trpbf.step/lt3061ems8e-trpbf.glbare the bare package body.
Provenance
Data extracted from the manufacturer datasheet, not a distributor listing:
- Datasheet: Analog Devices datasheet (22 pp, sha256
a0c80e42c07d86ae, retrieved 2026-10-29, tier: manufacturer) - Extractor: parts-factory
2.0.0/extract_pins 0.3, primaryclaude-haiku-5-5(text), consensusclaude-sonnet-5-5(agreed), guards: pin_guards 0.1: passed. Pins are checked against the footprint pad set and their cited datasheet pages before publish. - CAD: KiCad official libraries (CC-BY-SA 4.0).