main
Ray Publish 0.1.0 180814a

LT3060EDC#TRMPBF

Analog Devices · Linear Voltage Regulators (LDO) · DFN-8-EP(2x2)

LT3060EDC#TRMPBF from Analog Devices, in a DFN-8-EP(2x2). Pinout and pin descriptions extracted from the manufacturer datasheet (extract_pins, cross-checked by a second model); symbol, footprint, and 3D from KiCad-official CAD.

Pinout

Pin Name Type Function
1 REF/BYP passive Reference/bypass pin: a capacitor to GND (10nF typical gives 30µVRMS noise, 10Hz to 100kHz) sets reference noise and soft-start time; it is pulled low in shutdown, must be left floating if unused and must not be driven by active circuitry.
2 ADJ input Error amplifier inverting input referenced at 600mV to GND with 15nA typical bias current flowing out; a feedforward capacitor from ADJ to OUT reduces noise, and on fixed-voltage versions it must be left floating if not needed.
3 OUT power_out Regulator output supplying the load, needs a minimum 2.2µF ceramic output capacitor for stability, permissible output voltage range 600mV to 44.5V.
4 OUT power_out Regulator output supplying the load, needs a minimum 2.2µF ceramic output capacitor for stability, permissible output voltage range 600mV to 44.5V.
5 IN power_in Input supply pin for operation from 1.6V to 45V, with a local 1µF to 10µF bypass capacitor advisable, and it withstands reverse input voltage.
6 IN power_in Input supply pin for operation from 1.6V to 45V, with a local 1µF to 10µF bypass capacitor advisable, and it withstands reverse input voltage.
7 SHDN input Shutdown input where pulling low turns the output off, tie to IN if unused, the device does not function if left unconnected, and it cannot be driven below GND unless tied to IN.
8 GND power_in Ground pin, with the bottom of the adjustable-version resistor divider connected directly to it for optimum regulation, and tied directly to exposed pad Pin 9 and the PCB ground.
9 GND power_in Exposed pad is ground, must be soldered to the PCB, tied directly to Pin 8 and PCB ground for enhanced thermal performance.

Key specifications

Parameter Value
Manufacturer Analog Devices
Package DFN-8-EP(2x2)
Category Power Supply Chip
Pins 9

Electrical characteristics

Limits as printed in the datasheet (page.json metadata.characteristics carries them as data).

Parameter Symbol Min Typ Max Unit Conditions Page
ADJ Pin Voltage VADJ 594 600 606 mV VIN = 2.1V, ILOAD = 1mA 4
ADJ Pin Voltage (full temp range) VADJ 588 600 612 mV 2.1V < VIN < 45V, 1mA < ILOAD < 100mA (E-, I-Grades), over temperature 4
Minimum Input Voltage VIN(MIN) 1.6 2.1 V ILOAD = 100mA, over temperature 4
Line Regulation 0.6 3.5 mV ΔVIN = 2.1V to 45V, ILOAD = 1mA (E-, I-Grades), over temperature 4
Load Regulation 0.2 4 mV VIN = 2.1V, ILOAD = 1mA to 100mA (E-, I-Grades), over temperature 5
Dropout Voltage VDO 75 110 mV ILOAD = 1mA 5
Dropout Voltage (full temp range) VDO 180 mV ILOAD = 1mA, over temperature 5
Dropout Voltage VDO 150 200 mV ILOAD = 10mA 5
Dropout Voltage (full temp range) VDO 300 mV ILOAD = 10mA, over temperature 5
Dropout Voltage VDO 240 280 mV ILOAD = 50mA (Note 14) 5
Dropout Voltage (full temp range) VDO 410 mV ILOAD = 50mA (Note 14), over temperature 5
Dropout Voltage VDO 300 350 mV ILOAD = 100mA (Note 14) 5
Dropout Voltage (full temp range) VDO 510 mV ILOAD = 100mA (Note 14), over temperature 5
GND Pin Current IGND 40 80 µA ILOAD = 0µA, VIN = VOUT(NOMINAL) + 0.55V, over temperature 5
GND Pin Current IGND 60 100 µA ILOAD = 1mA, VIN = VOUT(NOMINAL) + 0.55V, over temperature 5
GND Pin Current IGND 160 350 µA ILOAD = 10mA, VIN = VOUT(NOMINAL) + 0.55V, over temperature 5
GND Pin Current IGND 0.8 1.8 mA ILOAD = 50mA, VIN = VOUT(NOMINAL) + 0.55V, over temperature 5
GND Pin Current IGND 2 4 mA ILOAD = 100mA, VIN = VOUT(NOMINAL) + 0.55V, over temperature 5
Quiescent Current in Shutdown IQ(SHDN) 0.3 1 µA VIN = 45V, VSHDN = 0V 5
ADJ Pin Bias Current IADJ 15 60 nA VIN = 2.1V, over temperature 5
Shutdown Threshold (Off to On) VSHDN 0.8 1.5 V VOUT = Off to On, over temperature 5
Shutdown Threshold (On to Off) VSHDN 0.3 0.7 V VOUT = On to Off, over temperature 5
SHDN Pin Current ISHDN 1 µA VSHDN = 0V, over temperature 5
SHDN Pin Current ISHDN 0.9 3 µA VSHDN = 45V, over temperature 5
Ripple Rejection 70 85 dB VRIPPLE = 0.5VP-P, fRIPPLE = 120Hz, ILOAD = 100mA, VIN = 2.1V (Avg) 5
Current Limit ILIM 200 mA VIN = 7V, VOUT = 0 5
Current Limit ILIM 110 mA VIN = VOUT(NOMINAL) + 1V (Notes 6, 12), ΔVOUT = -5%, over temperature 5
Input Reverse Leakage Current 300 µA VIN = -45V, VOUT = 0, over temperature 6
Reverse Output Current 0.2 10 µA VOUT = 1.2V, VIN = 0V 6
Output Voltage Noise 30 µVRMS COUT = 10µF, ILOAD = 100mA, CBYP = 0.01µF, VOUT = 600mV, BW = 10Hz to 100kHz 5
IN Pin Voltage -50 50 V 2
OUT Pin Voltage -50 50 V 2
Input-to-Output Differential Voltage -50 50 V Note 2 2
ADJ Pin Voltage -50 50 V 2
SHDN Pin Voltage -50 50 V 2
REF/BYP Pin Voltage -0.3 1 V 2
Operating Junction Temperature (E-Grade) TJ -40 125 °C E-, I-Grades (Notes 3, 5, 13) 2
Storage Temperature Range TSTG -65 150 °C 2
Input Voltage Range VIN 1.6 45 V 1
Thermal Resistance Junction-to-Ambient θJA 48 60 °C/W DC package, depends on copper area 2
Thermal Resistance Junction-to-Case θJC 20 °C/W DC package 2

Materials and finish

As the datasheet states them (page.json metadata.appearance; the 3D model's colours follow it).

Part Material Colour / plating Datasheet says Page
contacts COPPER Table 2. DC Package, 8-Lead DFN COPPER AREA 20

CAD (KiCad official)

  • Symbol: LT3060EDC#TRMPBF
  • Footprint: Package_DFN_QFN:DFN-8-1EP_2x2mm_P0.45mm_EP0.64x1.37mm
  • 3D model: DFN-8-EP(2x2) (KiCad packages3D, STEP)
  • 3D model files: lt3060edc-trmpbf-etched.step / lt3060edc-trmpbf-etched.glb carry the MPN laser-etched on the die in a toggleable Adom.LaserEtch group (Fusion-ready); lt3060edc-trmpbf.step / lt3060edc-trmpbf.glb are the bare package body.

Provenance

Data extracted from the manufacturer datasheet, not a distributor listing:

  • Datasheet: Analog Devices datasheet (26 pp, sha256 1da5b0984b8afdd3, retrieved 2026-10-30, tier: manufacturer)
  • Extractor: parts-factory 2.0.0 / extract_pins 0.3, primary claude-sonnet-5-5 (text), consensus claude-sonnet-5-5 (agreed), guards: pin_guards 0.1: passed. Pins are checked against the footprint pad set and their cited datasheet pages before publish.
  • CAD: KiCad official libraries (CC-BY-SA 4.0).

Datasheet PDF