3D Model
Open in new tab ↗
Loads when you scroll to it. Unloads after 5 minutes in the background.
Symbol & Footprint
Schematic Symbol
Open full view ↗Loads when you scroll to it. Unloads after 5 minutes in the background.
PCB Footprint
Open full view ↗Loads when you scroll to it. Unloads after 5 minutes in the background.
Datasheet
Open in new tab ↗Loads when you scroll to it. Unloads after 5 minutes in the background.
Contents
README
markdownLT3060EDC#TRMPBF
Analog Devices · Linear Voltage Regulators (LDO) · DFN-8-EP(2x2)
LT3060EDC#TRMPBF from Analog Devices, in a DFN-8-EP(2x2). Pinout and pin descriptions extracted from the manufacturer datasheet (extract_pins, cross-checked by a second model); symbol, footprint, and 3D from KiCad-official CAD.
Pinout
| Pin | Name | Type | Function |
|---|---|---|---|
| 1 | REF/BYP | passive | Reference/bypass pin: a capacitor to GND (10nF typical gives 30µVRMS noise, 10Hz to 100kHz) sets reference noise and soft-start time; it is pulled low in shutdown, must be left floating if unused and must not be driven by active circuitry. |
| 2 | ADJ | input | Error amplifier inverting input referenced at 600mV to GND with 15nA typical bias current flowing out; a feedforward capacitor from ADJ to OUT reduces noise, and on fixed-voltage versions it must be left floating if not needed. |
| 3 | OUT | power_out | Regulator output supplying the load, needs a minimum 2.2µF ceramic output capacitor for stability, permissible output voltage range 600mV to 44.5V. |
| 4 | OUT | power_out | Regulator output supplying the load, needs a minimum 2.2µF ceramic output capacitor for stability, permissible output voltage range 600mV to 44.5V. |
| 5 | IN | power_in | Input supply pin for operation from 1.6V to 45V, with a local 1µF to 10µF bypass capacitor advisable, and it withstands reverse input voltage. |
| 6 | IN | power_in | Input supply pin for operation from 1.6V to 45V, with a local 1µF to 10µF bypass capacitor advisable, and it withstands reverse input voltage. |
| 7 | SHDN | input | Shutdown input where pulling low turns the output off, tie to IN if unused, the device does not function if left unconnected, and it cannot be driven below GND unless tied to IN. |
| 8 | GND | power_in | Ground pin, with the bottom of the adjustable-version resistor divider connected directly to it for optimum regulation, and tied directly to exposed pad Pin 9 and the PCB ground. |
| 9 | GND | power_in | Exposed pad is ground, must be soldered to the PCB, tied directly to Pin 8 and PCB ground for enhanced thermal performance. |
Key specifications
| Parameter | Value |
|---|---|
| Manufacturer | Analog Devices |
| Package | DFN-8-EP(2x2) |
| Category | Power Supply Chip |
| Pins | 9 |
Electrical characteristics
Limits as printed in the datasheet (page.json metadata.characteristics carries them as data).
| Parameter | Symbol | Min | Typ | Max | Unit | Conditions | Page |
|---|---|---|---|---|---|---|---|
| ADJ Pin Voltage | VADJ | 594 | 600 | 606 | mV | VIN = 2.1V, ILOAD = 1mA | 4 |
| ADJ Pin Voltage (full temp range) | VADJ | 588 | 600 | 612 | mV | 2.1V < VIN < 45V, 1mA < ILOAD < 100mA (E-, I-Grades), over temperature | 4 |
| Minimum Input Voltage | VIN(MIN) | 1.6 | 2.1 | V | ILOAD = 100mA, over temperature | 4 | |
| Line Regulation | 0.6 | 3.5 | mV | ΔVIN = 2.1V to 45V, ILOAD = 1mA (E-, I-Grades), over temperature | 4 | ||
| Load Regulation | 0.2 | 4 | mV | VIN = 2.1V, ILOAD = 1mA to 100mA (E-, I-Grades), over temperature | 5 | ||
| Dropout Voltage | VDO | 75 | 110 | mV | ILOAD = 1mA | 5 | |
| Dropout Voltage (full temp range) | VDO | 180 | mV | ILOAD = 1mA, over temperature | 5 | ||
| Dropout Voltage | VDO | 150 | 200 | mV | ILOAD = 10mA | 5 | |
| Dropout Voltage (full temp range) | VDO | 300 | mV | ILOAD = 10mA, over temperature | 5 | ||
| Dropout Voltage | VDO | 240 | 280 | mV | ILOAD = 50mA (Note 14) | 5 | |
| Dropout Voltage (full temp range) | VDO | 410 | mV | ILOAD = 50mA (Note 14), over temperature | 5 | ||
| Dropout Voltage | VDO | 300 | 350 | mV | ILOAD = 100mA (Note 14) | 5 | |
| Dropout Voltage (full temp range) | VDO | 510 | mV | ILOAD = 100mA (Note 14), over temperature | 5 | ||
| GND Pin Current | IGND | 40 | 80 | µA | ILOAD = 0µA, VIN = VOUT(NOMINAL) + 0.55V, over temperature | 5 | |
| GND Pin Current | IGND | 60 | 100 | µA | ILOAD = 1mA, VIN = VOUT(NOMINAL) + 0.55V, over temperature | 5 | |
| GND Pin Current | IGND | 160 | 350 | µA | ILOAD = 10mA, VIN = VOUT(NOMINAL) + 0.55V, over temperature | 5 | |
| GND Pin Current | IGND | 0.8 | 1.8 | mA | ILOAD = 50mA, VIN = VOUT(NOMINAL) + 0.55V, over temperature | 5 | |
| GND Pin Current | IGND | 2 | 4 | mA | ILOAD = 100mA, VIN = VOUT(NOMINAL) + 0.55V, over temperature | 5 | |
| Quiescent Current in Shutdown | IQ(SHDN) | 0.3 | 1 | µA | VIN = 45V, VSHDN = 0V | 5 | |
| ADJ Pin Bias Current | IADJ | 15 | 60 | nA | VIN = 2.1V, over temperature | 5 | |
| Shutdown Threshold (Off to On) | VSHDN | 0.8 | 1.5 | V | VOUT = Off to On, over temperature | 5 | |
| Shutdown Threshold (On to Off) | VSHDN | 0.3 | 0.7 | V | VOUT = On to Off, over temperature | 5 | |
| SHDN Pin Current | ISHDN | 1 | µA | VSHDN = 0V, over temperature | 5 | ||
| SHDN Pin Current | ISHDN | 0.9 | 3 | µA | VSHDN = 45V, over temperature | 5 | |
| Ripple Rejection | 70 | 85 | dB | VRIPPLE = 0.5VP-P, fRIPPLE = 120Hz, ILOAD = 100mA, VIN = 2.1V (Avg) | 5 | ||
| Current Limit | ILIM | 200 | mA | VIN = 7V, VOUT = 0 | 5 | ||
| Current Limit | ILIM | 110 | mA | VIN = VOUT(NOMINAL) + 1V (Notes 6, 12), ΔVOUT = -5%, over temperature | 5 | ||
| Input Reverse Leakage Current | 300 | µA | VIN = -45V, VOUT = 0, over temperature | 6 | |||
| Reverse Output Current | 0.2 | 10 | µA | VOUT = 1.2V, VIN = 0V | 6 | ||
| Output Voltage Noise | 30 | µVRMS | COUT = 10µF, ILOAD = 100mA, CBYP = 0.01µF, VOUT = 600mV, BW = 10Hz to 100kHz | 5 | |||
| IN Pin Voltage | -50 | 50 | V | 2 | |||
| OUT Pin Voltage | -50 | 50 | V | 2 | |||
| Input-to-Output Differential Voltage | -50 | 50 | V | Note 2 | 2 | ||
| ADJ Pin Voltage | -50 | 50 | V | 2 | |||
| SHDN Pin Voltage | -50 | 50 | V | 2 | |||
| REF/BYP Pin Voltage | -0.3 | 1 | V | 2 | |||
| Operating Junction Temperature (E-Grade) | TJ | -40 | 125 | °C | E-, I-Grades (Notes 3, 5, 13) | 2 | |
| Storage Temperature Range | TSTG | -65 | 150 | °C | 2 | ||
| Input Voltage Range | VIN | 1.6 | 45 | V | 1 | ||
| Thermal Resistance Junction-to-Ambient | θJA | 48 | 60 | °C/W | DC package, depends on copper area | 2 | |
| Thermal Resistance Junction-to-Case | θJC | 20 | °C/W | DC package | 2 |
Materials and finish
As the datasheet states them (page.json metadata.appearance; the 3D model's colours follow it).
| Part | Material | Colour / plating | Datasheet says | Page |
|---|---|---|---|---|
| contacts | COPPER | Table 2. DC Package, 8-Lead DFN COPPER AREA | 20 |
CAD (KiCad official)
- Symbol:
LT3060EDC#TRMPBF - Footprint:
Package_DFN_QFN:DFN-8-1EP_2x2mm_P0.45mm_EP0.64x1.37mm - 3D model: DFN-8-EP(2x2) (KiCad packages3D, STEP)
- 3D model files:
lt3060edc-trmpbf-etched.step/lt3060edc-trmpbf-etched.glbcarry the MPN laser-etched on the die in a toggleableAdom.LaserEtchgroup (Fusion-ready);lt3060edc-trmpbf.step/lt3060edc-trmpbf.glbare the bare package body.
Provenance
Data extracted from the manufacturer datasheet, not a distributor listing:
- Datasheet: Analog Devices datasheet (26 pp, sha256
1da5b0984b8afdd3, retrieved 2026-10-30, tier: manufacturer) - Extractor: parts-factory
2.0.0/extract_pins 0.3, primaryclaude-sonnet-5-5(text), consensusclaude-sonnet-5-5(agreed), guards: pin_guards 0.1: passed. Pins are checked against the footprint pad set and their cited datasheet pages before publish. - CAD: KiCad official libraries (CC-BY-SA 4.0).