component
LT3060EDC-3.3#TRPBF
Public Made by Adomby adom
Analog Devices Linear Voltage Regulators (LDO), DFN-8-EP(2x2). Pinout cross-checked by two models against the datasheet, KiCad symbol/footprint/3D.
main
LT3060EDC-3.3#TRPBF
Analog Devices · Linear Voltage Regulators (LDO) · DFN-8-EP(2x2)
LT3060EDC-3.3#TRPBF from Analog Devices, in a DFN-8-EP(2x2). Pinout and pin descriptions extracted from the manufacturer datasheet (extract_pins, cross-checked by a second model); symbol, footprint, and 3D from KiCad-official CAD.
Pinout
| Pin | Name | Type | Function |
|---|---|---|---|
| 1 | REF/BYP | passive | A single capacitor from this pin to GND bypasses the reference noise and soft-starts the reference (10nF typically gives 30µVRMS noise over 10Hz to 100kHz), and the pin must not be driven by active circuitry and must be left floating if low noise or soft-start is not required. |
| 2 | ADJ | input | This is the error amplifier's inverting input with a typical 15nA bias flowing out of the pin and 600mV referenced to GND, and for fixed-voltage versions it must be left floating if low noise and fast transient response are not required. |
| 3 | OUT | power_out | This pin supplies power to the load, requires a minimum 2.2µF ceramic output capacitor for stability, and the permissible output voltage range is 600mV to 44.5V. |
| 4 | OUT | power_out | This pin supplies power to the load and is internally connected with pin 3 as an output, with the same 2.2µF minimum ceramic output capacitor requirement and 600mV to 44.5V permissible output range. |
| 5 | IN | power_in | This pin supplies power to the device over the 1.6V to 45V input range, needs a 1µF to 10µF bypass capacitor (local to the pin if more than six inches from the main input filter), and withstands reverse voltage relative to GND and OUT. |
| 6 | IN | power_in | This pin supplies power to the device over the 1.6V to 45V input range and is internally connected with pin 5 as an input, with the same 1µF to 10µF bypass capacitor guidance and reverse-voltage withstand. |
| 7 | SHDN | input | Pulling this pin low puts the LT3060 into shutdown and turns the output off, it must not be driven below GND unless tied to IN, the device does not function if the pin is left unconnected, and it is connected to IN if unused. |
| 8 | GND | power_in | This is the ground pin, which for the DFN package must be tied to the exposed pad (pin 9) and the PCB ground. |
| 9 | GND | power_in | The exposed pad is GND, must be soldered to the PCB, and provides enhanced thermal performance through its connection to PCB ground with TJMAX = 125°C and θJA = 48°C/W to 60°C/W for the DFN package. |
Key specifications
| Parameter | Value |
|---|---|
| Manufacturer | Analog Devices |
| Package | DFN-8-EP(2x2) |
| Category | Power Management ICs |
| Pins | 9 |
Electrical characteristics
Limits as printed in the datasheet (page.json metadata.characteristics carries them as data).
| Parameter | Symbol | Min | Typ | Max | Unit | Conditions | Page |
|---|---|---|---|---|---|---|---|
| Regulated Output Voltage (25°C) | VOUT | 3.267 | 3.3 | 3.333 | V | VIN = 3.85V, ILOAD = 1mA | 4 |
| Regulated Output Voltage (E-, I-Grades, over temperature) | VOUT | 3.234 | 3.3 | 3.366 | V | 3.85V < VIN < 45V, 1mA < ILOAD < 100mA (E-, I-Grades) | 4 |
| Minimum Input Voltage | 1.6 | 2.1 | V | ILOAD = 100mA (over temperature range) | 4 | ||
| Line Regulation (E-, I-Grades) | 1.3 | 7 | mV | ΔVIN = 3.85V to 45V, ILOAD = 1mA (E-, I-Grades) | 4 | ||
| Load Regulation (E-, I-Grades) | 3.1 | 24 | mV | VIN = 3.85V, ILOAD = 1mA to 100mA (E-, I-Grades) | 5 | ||
| Dropout Voltage | VDO | 75 | 110 | mV | VIN = VOUT(NOMINAL), ILOAD = 1mA | 5 | |
| Dropout Voltage (over temperature) | VDO | 180 | mV | VIN = VOUT(NOMINAL), ILOAD = 1mA (over temperature range) | 5 | ||
| Dropout Voltage | VDO | 150 | 200 | mV | VIN = VOUT(NOMINAL), ILOAD = 10mA | 5 | |
| Dropout Voltage (over temperature) | VDO | 300 | mV | VIN = VOUT(NOMINAL), ILOAD = 10mA (over temperature range) | 5 | ||
| Dropout Voltage | VDO | 240 | 280 | mV | VIN = VOUT(NOMINAL), ILOAD = 50mA (Note 14) | 5 | |
| Dropout Voltage (over temperature) | VDO | 410 | mV | VIN = VOUT(NOMINAL), ILOAD = 50mA (Note 14, over temperature range) | 5 | ||
| Dropout Voltage | VDO | 300 | 350 | mV | VIN = VOUT(NOMINAL), ILOAD = 100mA (Note 14) | 5 | |
| Dropout Voltage (over temperature) | VDO | 510 | mV | VIN = VOUT(NOMINAL), ILOAD = 100mA (Note 14, over temperature range) | 5 | ||
| GND Pin Current | 40 | 80 | µA | VIN = VOUT(NOMINAL) + 0.55V, ILOAD = 0µA | 5 | ||
| GND Pin Current | 60 | 100 | µA | VIN = VOUT(NOMINAL) + 0.55V, ILOAD = 1mA | 5 | ||
| GND Pin Current | 160 | 350 | µA | VIN = VOUT(NOMINAL) + 0.55V, ILOAD = 10mA | 5 | ||
| GND Pin Current | 0.8 | 1.8 | mA | VIN = VOUT(NOMINAL) + 0.55V, ILOAD = 50mA | 5 | ||
| GND Pin Current | 2 | 4 | mA | VIN = VOUT(NOMINAL) + 0.55V, ILOAD = 100mA | 5 | ||
| Quiescent Current in Shutdown | 0.3 | 1 | µA | VIN = 45V, VSHDN = 0V | 5 | ||
| ADJ Pin Bias Current | 15 | 60 | nA | VIN = 2.1V (over temperature range) | 5 | ||
| SHDN Pin Current | 0.9 | µA | VSHDN = 0V (over temperature range) | 5 | |||
| SHDN Pin Current | 1 | 3 | µA | VSHDN = 45V (over temperature range) | 5 | ||
| Shutdown Threshold (Off to On) | 0.3 | 0.8 | V | VOUT = Off to On (over temperature range) | 5 | ||
| Shutdown Threshold (On to Off) | 0.7 | 1.5 | V | VOUT = On to Off (over temperature range) | 5 | ||
| Ripple Rejection | 55 | 70 | dB | VRIPPLE = 0.5VP-P, fRIPPLE = 120Hz, ILOAD = 100mA, VIN = 4.8V (Avg) | 5 | ||
| Current Limit | 110 | 200 | mA | VIN = VOUT(NOMINAL) + 1V (Notes 6, 12), ΔVOUT = -5% (over temperature range for min) | 5 | ||
| Input Reverse Leakage Current | 300 | µA | VIN = -45V, VOUT = 0 (over temperature range) | 6 | |||
| Reverse Output Current | 5 | 10 | µA | VOUT = 3.3V, VIN = 0V | 6 | ||
| IN Pin Voltage | VIN | -50 | 50 | V | 2 | ||
| OUT Pin Voltage | VOUT | -50 | 50 | V | 2 | ||
| Input-to-Output Differential Voltage | VIN-VOUT | -50 | 50 | V | Note 2 | 2 | |
| ADJ Pin Voltage | VADJ | -50 | 50 | V | 2 | ||
| SHDN Pin Voltage | VSHDN | -50 | 50 | V | 2 | ||
| REF/BYP Pin Voltage | VREF/BYP | -0.3 | 1 | V | Note 1 | 2 | |
| Operating Junction Temperature (E-, I-Grades) | TJ | -40 | 125 | °C | E-, I-Grades | 2 | |
| Storage Temperature Range | TSTG | -65 | 150 | °C | 2 | ||
| Maximum Junction Temperature (DFN) | TJMAX | 125 | °C | DC (DFN) package, E-, I-Grades | 2 | ||
| Thermal Resistance, Junction-to-Ambient (DFN) | θJA | 48 | 60 | °C/W | DFN, depends on copper area (see Table 2) | 2 | |
| Thermal Resistance, Junction-to-Case (DFN) | θJC | 20 | °C/W | DFN package | 2 | ||
| Input Voltage Range | VIN | 1.6 | 45 | V | Operating input supply range (description) | 1 | |
| Permissible Output Voltage Range | VOUT | 0.6 | 44.5 | V | OUT pin (pin function description) | 15 |
Materials and finish
As the datasheet states them (page.json metadata.appearance; the 3D model's colours follow it).
| Part | Material | Colour / plating | Datasheet says | Page |
|---|---|---|---|---|
| contacts | COPPER | Table 2. DC Package, 8-Lead DFN COPPER AREA | 20 |
CAD (KiCad official)
- Symbol:
LT3060EDC-3.3#TRPBF - Footprint:
Package_DFN_QFN:DFN-8-1EP_2x2mm_P0.45mm_EP0.64x1.37mm - 3D model: DFN-8-EP(2x2) (KiCad packages3D, STEP)
- 3D model files:
lt3060edc-3-3-trpbf-etched.step/lt3060edc-3-3-trpbf-etched.glbcarry the MPN laser-etched on the die in a toggleableAdom.LaserEtchgroup (Fusion-ready);lt3060edc-3-3-trpbf.step/lt3060edc-3-3-trpbf.glbare the bare package body.
Provenance
Data extracted from the manufacturer datasheet, not a distributor listing:
- Datasheet: Analog Devices datasheet (26 pp, sha256
1da5b0984b8afdd3, retrieved 2026-10-29, tier: manufacturer) - Extractor: parts-factory
2.0.0/extract_pins 0.3, primaryclaude-haiku-5-5(text), consensusclaude-sonnet-5-5(agreed), guards: pin_guards 0.1: passed. Pins are checked against the footprint pad set and their cited datasheet pages before publish. - CAD: KiCad official libraries (CC-BY-SA 4.0).
# LT3060EDC-3.3#TRPBF
**Analog Devices** · Linear Voltage Regulators (LDO) · DFN-8-EP(2x2)
LT3060EDC-3.3#TRPBF from Analog Devices, in a DFN-8-EP(2x2). Pinout and pin descriptions extracted from the manufacturer datasheet (extract_pins, cross-checked by a second model); symbol, footprint, and 3D from KiCad-official CAD.
## Pinout
| Pin | Name | Type | Function |
|---|---|---|---|
| 1 | REF/BYP | passive | A single capacitor from this pin to GND bypasses the reference noise and soft-starts the reference (10nF typically gives 30µVRMS noise over 10Hz to 100kHz), and the pin must not be driven by active circuitry and must be left floating if low noise or soft-start is not required. |
| 2 | ADJ | input | This is the error amplifier's inverting input with a typical 15nA bias flowing out of the pin and 600mV referenced to GND, and for fixed-voltage versions it must be left floating if low noise and fast transient response are not required. |
| 3 | OUT | power_out | This pin supplies power to the load, requires a minimum 2.2µF ceramic output capacitor for stability, and the permissible output voltage range is 600mV to 44.5V. |
| 4 | OUT | power_out | This pin supplies power to the load and is internally connected with pin 3 as an output, with the same 2.2µF minimum ceramic output capacitor requirement and 600mV to 44.5V permissible output range. |
| 5 | IN | power_in | This pin supplies power to the device over the 1.6V to 45V input range, needs a 1µF to 10µF bypass capacitor (local to the pin if more than six inches from the main input filter), and withstands reverse voltage relative to GND and OUT. |
| 6 | IN | power_in | This pin supplies power to the device over the 1.6V to 45V input range and is internally connected with pin 5 as an input, with the same 1µF to 10µF bypass capacitor guidance and reverse-voltage withstand. |
| 7 | SHDN | input | Pulling this pin low puts the LT3060 into shutdown and turns the output off, it must not be driven below GND unless tied to IN, the device does not function if the pin is left unconnected, and it is connected to IN if unused. |
| 8 | GND | power_in | This is the ground pin, which for the DFN package must be tied to the exposed pad (pin 9) and the PCB ground. |
| 9 | GND | power_in | The exposed pad is GND, must be soldered to the PCB, and provides enhanced thermal performance through its connection to PCB ground with TJMAX = 125°C and θJA = 48°C/W to 60°C/W for the DFN package. |
## Key specifications
| Parameter | Value |
|---|---|
| Manufacturer | Analog Devices |
| Package | DFN-8-EP(2x2) |
| Category | Power Management ICs |
| Pins | 9 |
## Electrical characteristics
Limits as printed in the datasheet (page.json `metadata.characteristics` carries them as data).
| Parameter | Symbol | Min | Typ | Max | Unit | Conditions | Page |
|---|---|---|---|---|---|---|---|
| Regulated Output Voltage (25°C) | VOUT | 3.267 | 3.3 | 3.333 | V | VIN = 3.85V, ILOAD = 1mA | 4 |
| Regulated Output Voltage (E-, I-Grades, over temperature) | VOUT | 3.234 | 3.3 | 3.366 | V | 3.85V < VIN < 45V, 1mA < ILOAD < 100mA (E-, I-Grades) | 4 |
| Minimum Input Voltage | | | 1.6 | 2.1 | V | ILOAD = 100mA (over temperature range) | 4 |
| Line Regulation (E-, I-Grades) | | | 1.3 | 7 | mV | ΔVIN = 3.85V to 45V, ILOAD = 1mA (E-, I-Grades) | 4 |
| Load Regulation (E-, I-Grades) | | | 3.1 | 24 | mV | VIN = 3.85V, ILOAD = 1mA to 100mA (E-, I-Grades) | 5 |
| Dropout Voltage | VDO | | 75 | 110 | mV | VIN = VOUT(NOMINAL), ILOAD = 1mA | 5 |
| Dropout Voltage (over temperature) | VDO | | | 180 | mV | VIN = VOUT(NOMINAL), ILOAD = 1mA (over temperature range) | 5 |
| Dropout Voltage | VDO | | 150 | 200 | mV | VIN = VOUT(NOMINAL), ILOAD = 10mA | 5 |
| Dropout Voltage (over temperature) | VDO | | | 300 | mV | VIN = VOUT(NOMINAL), ILOAD = 10mA (over temperature range) | 5 |
| Dropout Voltage | VDO | | 240 | 280 | mV | VIN = VOUT(NOMINAL), ILOAD = 50mA (Note 14) | 5 |
| Dropout Voltage (over temperature) | VDO | | | 410 | mV | VIN = VOUT(NOMINAL), ILOAD = 50mA (Note 14, over temperature range) | 5 |
| Dropout Voltage | VDO | | 300 | 350 | mV | VIN = VOUT(NOMINAL), ILOAD = 100mA (Note 14) | 5 |
| Dropout Voltage (over temperature) | VDO | | | 510 | mV | VIN = VOUT(NOMINAL), ILOAD = 100mA (Note 14, over temperature range) | 5 |
| GND Pin Current | | | 40 | 80 | µA | VIN = VOUT(NOMINAL) + 0.55V, ILOAD = 0µA | 5 |
| GND Pin Current | | | 60 | 100 | µA | VIN = VOUT(NOMINAL) + 0.55V, ILOAD = 1mA | 5 |
| GND Pin Current | | | 160 | 350 | µA | VIN = VOUT(NOMINAL) + 0.55V, ILOAD = 10mA | 5 |
| GND Pin Current | | | 0.8 | 1.8 | mA | VIN = VOUT(NOMINAL) + 0.55V, ILOAD = 50mA | 5 |
| GND Pin Current | | | 2 | 4 | mA | VIN = VOUT(NOMINAL) + 0.55V, ILOAD = 100mA | 5 |
| Quiescent Current in Shutdown | | | 0.3 | 1 | µA | VIN = 45V, VSHDN = 0V | 5 |
| ADJ Pin Bias Current | | | 15 | 60 | nA | VIN = 2.1V (over temperature range) | 5 |
| SHDN Pin Current | | | | 0.9 | µA | VSHDN = 0V (over temperature range) | 5 |
| SHDN Pin Current | | | 1 | 3 | µA | VSHDN = 45V (over temperature range) | 5 |
| Shutdown Threshold (Off to On) | | 0.3 | | 0.8 | V | VOUT = Off to On (over temperature range) | 5 |
| Shutdown Threshold (On to Off) | | 0.7 | | 1.5 | V | VOUT = On to Off (over temperature range) | 5 |
| Ripple Rejection | | 55 | 70 | | dB | VRIPPLE = 0.5VP-P, fRIPPLE = 120Hz, ILOAD = 100mA, VIN = 4.8V (Avg) | 5 |
| Current Limit | | 110 | 200 | | mA | VIN = VOUT(NOMINAL) + 1V (Notes 6, 12), ΔVOUT = -5% (over temperature range for min) | 5 |
| Input Reverse Leakage Current | | | | 300 | µA | VIN = -45V, VOUT = 0 (over temperature range) | 6 |
| Reverse Output Current | | | 5 | 10 | µA | VOUT = 3.3V, VIN = 0V | 6 |
| IN Pin Voltage | VIN | -50 | | 50 | V | | 2 |
| OUT Pin Voltage | VOUT | -50 | | 50 | V | | 2 |
| Input-to-Output Differential Voltage | VIN-VOUT | -50 | | 50 | V | Note 2 | 2 |
| ADJ Pin Voltage | VADJ | -50 | | 50 | V | | 2 |
| SHDN Pin Voltage | VSHDN | -50 | | 50 | V | | 2 |
| REF/BYP Pin Voltage | VREF/BYP | -0.3 | | 1 | V | Note 1 | 2 |
| Operating Junction Temperature (E-, I-Grades) | TJ | -40 | | 125 | °C | E-, I-Grades | 2 |
| Storage Temperature Range | TSTG | -65 | | 150 | °C | | 2 |
| Maximum Junction Temperature (DFN) | TJMAX | | | 125 | °C | DC (DFN) package, E-, I-Grades | 2 |
| Thermal Resistance, Junction-to-Ambient (DFN) | θJA | 48 | | 60 | °C/W | DFN, depends on copper area (see Table 2) | 2 |
| Thermal Resistance, Junction-to-Case (DFN) | θJC | | 20 | | °C/W | DFN package | 2 |
| Input Voltage Range | VIN | 1.6 | | 45 | V | Operating input supply range (description) | 1 |
| Permissible Output Voltage Range | VOUT | 0.6 | | 44.5 | V | OUT pin (pin function description) | 15 |
## Materials and finish
As the datasheet states them (page.json `metadata.appearance`; the 3D model's colours follow it).
| Part | Material | Colour / plating | Datasheet says | Page |
|---|---|---|---|---|
| contacts | COPPER | | Table 2. DC Package, 8-Lead DFN COPPER AREA | 20 |
## CAD (KiCad official)
- Symbol: `LT3060EDC-3.3#TRPBF`
- Footprint: `Package_DFN_QFN:DFN-8-1EP_2x2mm_P0.45mm_EP0.64x1.37mm`
- 3D model: DFN-8-EP(2x2) (KiCad packages3D, STEP)
- 3D model files: `lt3060edc-3-3-trpbf-etched.step` / `lt3060edc-3-3-trpbf-etched.glb` carry the MPN laser-etched on the die in a toggleable `Adom.LaserEtch` group (Fusion-ready); `lt3060edc-3-3-trpbf.step` / `lt3060edc-3-3-trpbf.glb` are the bare package body.
## Provenance
Data extracted from the manufacturer datasheet, not a distributor listing:
- **Datasheet:** [Analog Devices datasheet](https://www.analog.com/media/en/technical-documentation/data-sheets/lt3060.pdf) (26 pp, sha256 `1da5b0984b8afdd3`, retrieved 2026-10-29, tier: manufacturer)
- **Extractor:** parts-factory `2.0.0` / `extract_pins 0.3`, primary `claude-haiku-5-5` (text), consensus `claude-sonnet-5-5` (agreed), guards: pin_guards 0.1: passed. Pins are checked against the footprint pad set and their cited datasheet pages before publish.
- **CAD:** KiCad official libraries (CC-BY-SA 4.0).
[Datasheet PDF](docs/lt3060edc-3-3-trpbf-datasheet.pdf)