main
Ray
Publish 0.1.0
19d4913
LS7366R-TS
LSI/CSI · Counters / Dividers · TSSOP-14
LS7366R-TS from LSI/CSI, in a TSSOP-14. Pinout and pin descriptions extracted from the manufacturer datasheet (extract_pins, cross-checked by a second model); symbol, footprint, and 3D from KiCad-official CAD.
Pinout
| Pin | Name | Type | Function |
|---|---|---|---|
| 1 | fCKO | output | Crystal oscillator output; a crystal connected between fCKO and fCKi generates the basic filter clock used for the A, B and INDEX/ inputs in quadrature count mode. |
| 2 | fCKi | input | Filter clock input that accepts a crystal or an external clock, divided by 2 when MDR0 bit 7 is 1 and by 1 when it is 0, and must satisfy the filter-clock condition relative to the maximum Clock A quadrature frequency fQA; it is not used in non-quadrature mode. |
| 3 | VSS | power_in | Ground reference for the device; all absolute maximum voltage ratings are referenced to VSS. |
| 4 | SS/ | input | Active-low slave select: a high-to-low transition selects the device for serial transfer, and a low-to-high transition ends the transfer and forces MISO to high impedance. |
| 5 | SCK | input | Serial shift clock supplied by the host master that clocks MOSI in on its rising edge and MISO out on its falling edge. |
| 6 | MISO | tri_state | Serial data output shifted out MSB first on the falling edge of SCK; it is high impedance when SS/ is high so multiple slave outputs can be wire-ORed. |
| 7 | MOSI | input | Serial data input from the host processor, shifted in MSB first on the rising edge of SCK. |
| 8 | LFLAG/ | output | Open-drain latched flag output for Carry, Borrow, Compare or Index that switches to logic 0 when active and returns to high impedance only when the status register STR is cleared. |
| 9 | DFLAG/ | output | Push-pull instantaneous flag output that switches low dynamically on Carry, Borrow, Compare and Index conditions. |
| 10 | INDEX/ | input | Programmable index input (load CNTR, reset CNTR, load OTR, or masked out) that is synchronous or asynchronous to A and B according to MDR0, and is always asynchronous in non-quadrature mode. |
| 11 | B | input | Quadrature clock B input from the encoder, filtered and decoded for direction and count; in non-quadrature mode it is the direction input (high enables up count, low enables down count) and is unfiltered. |
| 12 | A | input | Quadrature clock A input from the encoder, filtered and decoded for count clocks; in non-quadrature mode it is the count input and is unfiltered. |
| 13 | CNT_EN | input | Count enable: counting is enabled when high and disabled when low, with an internal pull-up resistor on this input. |
| 14 | VDD | power_in | Positive supply, specified at 3V to 5.5V (VDD - VSS), with an absolute maximum DC supply of 7.0 V. |
Key specifications
| Parameter | Value |
|---|---|
| Manufacturer | LSI/CSI |
| Package | TSSOP-14 |
| Category | Logic ICs |
| Pins | 14 |
Electrical characteristics
Limits as printed in the datasheet (page.json metadata.characteristics carries them as data).
| Parameter | Symbol | Min | Typ | Max | Unit | Conditions | Page |
|---|---|---|---|---|---|---|---|
| Operating Temperature | TA | -25 | 80 | oC | 4 | ||
| Storage Temperature | TSTG | -65 | 150 | oC | 4 | ||
| DC Supply Voltage | VDD | 7 | V | All voltages referenced to Vss | 4 | ||
| Supply Voltage | VDD | 3 | 5.5 | V | 5 | ||
| Supply Current | IDD | 300 | 400 | 450 | µA | VDD = 3.0V | 5 |
| Supply Current | IDD | 700 | 800 | 950 | µA | VDD = 5.0V | 5 |
| fCKi Logic high input voltage | VCH | 2.3 | V | VDD = 3.0V | 5 | ||
| fCKi Logic high input voltage | VCH | 3.7 | V | VDD = 5.0V | 5 | ||
| fCKi Logic low input voltage | VCL | 0.7 | V | VDD = 3.0V | 5 | ||
| fCKi Logic low input voltage | VCL | 1.3 | V | VDD = 5.0 | 5 | ||
| All other inputs Logic High input voltage | VAH | 2.1 | V | VDD = 3.0V | 5 | ||
| All other inputs Logic High input voltage | VAH | 3.5 | V | VDD = 5.0V | 5 | ||
| All other inputs Logic Low input voltage | VAL | 0.5 | V | VDD = 3.0V | 5 | ||
| All other inputs Logic Low input voltage | VAL | 1 | V | VDD = 5.0V | 5 | ||
| CNT_EN Low input current | IIEL | 3 | 5 | µA | VAL = 0.7V, VDD = 3.0V | 5 | |
| CNT_EN Low input current | IIEL | 10 | 15 | µA | VAL = 1.2V, VDD = 5.0V | 5 | |
| CNT_EN High input current | IIEH | 1 | 3 | µA | VAH = 1.9V, VDD = 3.0V | 5 | |
| CNT_EN High input current | IIEH | 6 | 9 | µA | VAH = 3.2V, VDD = 5.0V | 5 | |
| All other inputs, High or Low input current | 0 | 0 | µA | 5 | |||
| LFLAG, DFLAG Sink output current | IOFL | -1.3 | -2 | mA | VOUT = 0.5V, VDD = 3.0V | 5 | |
| LFLAG, DFLAG Sink output current | IOFL | -3.2 | -4 | mA | VOUT = 0.5V, VDD = 5.0V | 5 | |
| LFLAG Source output current | 0 | 0 | mA | Open Drain Output | 5 | ||
| DFLAG Source output current | IOFH | 1 | 1.8 | mA | VOUT = 2.5V, VDD = 3.0V | 5 | |
| DFLAG Source output current | IOFH | 2.8 | 3.6 | mA | VOUT = 4.5V, VDD = 5.0V | 5 | |
| fCKO Sink output current | IOCL | -1.3 | -2 | mA | VOUT = 0.5V, VDD = 3.0V | 5 | |
| fCKO Sink output current | IOCL | -3.2 | -4 | mA | VOUT = 0.5V, VDD = 5.0V | 5 | |
| fCKO Source output current | IOCH | 1.3 | 2 | mA | VOUT = 2.5V, VDD = 3.0V | 5 | |
| fCKO Source output current | IOCH | 3.2 | 4 | mA | VOUT = 4.5V, VDD = 5.0V | 5 | |
| TXD/MISO Sink output current | IOML | -1.5 | -2.4 | mA | VOUT = 0.5V, VDD = 3.0V | 5 | |
| TXD/MISO Sink output current | IOML | -3.8 | -4.8 | mA | VOUT = 0.5V, VDD = 5.0V | 5 | |
| TXD/MISO Source output current | IOMH | 1.5 | 2.4 | mA | VOUT = 2.5V, VDD = 3.0V | 5 | |
| TXD/MISO Source output current | IOMH | 3.8 | 4.8 | mA | VOUT = 4.5V, VDD = 5.0V | 5 | |
| SCK High Pulse Width | tCH | 100 | ns | 5 | |||
| SCK Low Pulse Width | tCL | 100 | ns | 5 | |||
| SS/ Set Up Time | tCSL | 100 | ns | 5 | |||
| SS/ Hold Time | tCSH | 100 | ns | 5 | |||
| Inter Command SS/ high | tCSI | 100 | ns | 5 | |||
| fCKI High Pulse Width | t1 | 12 | ns | 5 | |||
| fCKI Pulse Width | t2 | 12 | ns | 5 | |||
| fCKI Frequency | fFCK | 40 | MHz | 5 | |||
| Effective Filter Clock fF Period | t3 | 25 | ns | t3 = t1+t2, MDR0 <7> = 0 | 5 | ||
| Effective Filter Clock fF Period | t3 | 50 | ns | t3 = 2(t1+t2), MDR0 <7> = 1 | 5 | ||
| Effective Filter Clock fF frequency | fF | 40 | MHz | fF = 1/ t3 | 5 | ||
| Quadrature Separation | t4 | 26 | ns | t4 > t3 | 5 | ||
| Quadrature Clock Pulse Width | t5 | 52 | ns | t5 2t3 | 5 | ||
| Quadrature Clock frequency | fQA, fQB | 9.6 | MHz | fQA = fQB < 1/4t3 | 5 | ||
| x1 / x2 / x4 Count Clock Pulse Width | tQ2 | 12 | ns | tQ2 = (t3)/2 | 5 | ||
| Index Input Pulse Width | tid | 32 | ns | tid > t4 | 5 | ||
| Index Set Up Time | tis | 5 | ns | 5 | |||
| Index Hold Time | tih | 5 | ns | 5 | |||
| DFLAG/ output width | tfw | 26 | ns | tfw = t4 | 5 | ||
| Clock A High Pulse Width | t6 | 12 | ns | 6 | |||
| Clock A Low Pulse Width | t7 | 12 | ns | 6 | |||
| Direction Input B Set-up Time | t8S | 12 | ns | 6 | |||
| Direction Input B Hold Time | t8H | 10 | ns | 6 | |||
| CNT_EN Set-up Time | t9S | 12 | ns | 6 | |||
| CNT_EN Hold Time | t9H | 12 | ns | 6 | |||
| Clock Frequency (non-Mod-N) | fA | 40 | MHz | fA = (1/(t6 + t7)) | 6 | ||
| Clock to DFLAG/ or LFLAG/ delay | t10 | 20 | ns | 6 | |||
| DFLAG/ output width | t11 | 12 | ns | t10 = t7 | 6 |
CAD (KiCad official)
- Symbol:
LS7366R-TS - Footprint:
Package_SO:TSSOP-14_4.4x5mm_P0.65mm - 3D model: TSSOP-14 (KiCad packages3D, STEP)
- 3D model files:
ls7366r-ts-etched.step/ls7366r-ts-etched.glbcarry the MPN laser-etched on the die in a toggleableAdom.LaserEtchgroup (Fusion-ready);ls7366r-ts.step/ls7366r-ts.glbare the bare package body.
Provenance
Data extracted from the manufacturer datasheet, not a distributor listing:
- Datasheet: LSI/CSI datasheet (17 pp, sha256
51b1ffc0846b8ad0, retrieved 2026-11-05, tier: lcsc) - Extractor: parts-factory
2.0.0/extract_pins 0.3, primaryclaude-haiku-5-5(text), consensusclaude-sonnet-5-5(agreed), guards: pin_guards 0.1: passed. Pins are checked against the footprint pad set and their cited datasheet pages before publish. - CAD: KiCad official libraries (CC-BY-SA 4.0).
# LS7366R-TS
**LSI/CSI** · Counters / Dividers · TSSOP-14
LS7366R-TS from LSI/CSI, in a TSSOP-14. Pinout and pin descriptions extracted from the manufacturer datasheet (extract_pins, cross-checked by a second model); symbol, footprint, and 3D from KiCad-official CAD.
## Pinout
| Pin | Name | Type | Function |
|---|---|---|---|
| 1 | fCKO | output | Crystal oscillator output; a crystal connected between fCKO and fCKi generates the basic filter clock used for the A, B and INDEX/ inputs in quadrature count mode. |
| 2 | fCKi | input | Filter clock input that accepts a crystal or an external clock, divided by 2 when MDR0 bit 7 is 1 and by 1 when it is 0, and must satisfy the filter-clock condition relative to the maximum Clock A quadrature frequency fQA; it is not used in non-quadrature mode. |
| 3 | VSS | power_in | Ground reference for the device; all absolute maximum voltage ratings are referenced to VSS. |
| 4 | SS/ | input | Active-low slave select: a high-to-low transition selects the device for serial transfer, and a low-to-high transition ends the transfer and forces MISO to high impedance. |
| 5 | SCK | input | Serial shift clock supplied by the host master that clocks MOSI in on its rising edge and MISO out on its falling edge. |
| 6 | MISO | tri_state | Serial data output shifted out MSB first on the falling edge of SCK; it is high impedance when SS/ is high so multiple slave outputs can be wire-ORed. |
| 7 | MOSI | input | Serial data input from the host processor, shifted in MSB first on the rising edge of SCK. |
| 8 | LFLAG/ | output | Open-drain latched flag output for Carry, Borrow, Compare or Index that switches to logic 0 when active and returns to high impedance only when the status register STR is cleared. |
| 9 | DFLAG/ | output | Push-pull instantaneous flag output that switches low dynamically on Carry, Borrow, Compare and Index conditions. |
| 10 | INDEX/ | input | Programmable index input (load CNTR, reset CNTR, load OTR, or masked out) that is synchronous or asynchronous to A and B according to MDR0, and is always asynchronous in non-quadrature mode. |
| 11 | B | input | Quadrature clock B input from the encoder, filtered and decoded for direction and count; in non-quadrature mode it is the direction input (high enables up count, low enables down count) and is unfiltered. |
| 12 | A | input | Quadrature clock A input from the encoder, filtered and decoded for count clocks; in non-quadrature mode it is the count input and is unfiltered. |
| 13 | CNT_EN | input | Count enable: counting is enabled when high and disabled when low, with an internal pull-up resistor on this input. |
| 14 | VDD | power_in | Positive supply, specified at 3V to 5.5V (VDD - VSS), with an absolute maximum DC supply of 7.0 V. |
## Key specifications
| Parameter | Value |
|---|---|
| Manufacturer | LSI/CSI |
| Package | TSSOP-14 |
| Category | Logic ICs |
| Pins | 14 |
## Electrical characteristics
Limits as printed in the datasheet (page.json `metadata.characteristics` carries them as data).
| Parameter | Symbol | Min | Typ | Max | Unit | Conditions | Page |
|---|---|---|---|---|---|---|---|
| Operating Temperature | TA | -25 | | 80 | oC | | 4 |
| Storage Temperature | TSTG | -65 | | 150 | oC | | 4 |
| DC Supply Voltage | VDD | | | 7 | V | All voltages referenced to Vss | 4 |
| Supply Voltage | VDD | 3 | | 5.5 | V | | 5 |
| Supply Current | IDD | 300 | 400 | 450 | µA | VDD = 3.0V | 5 |
| Supply Current | IDD | 700 | 800 | 950 | µA | VDD = 5.0V | 5 |
| fCKi Logic high input voltage | VCH | 2.3 | | | V | VDD = 3.0V | 5 |
| fCKi Logic high input voltage | VCH | 3.7 | | | V | VDD = 5.0V | 5 |
| fCKi Logic low input voltage | VCL | | | 0.7 | V | VDD = 3.0V | 5 |
| fCKi Logic low input voltage | VCL | | | 1.3 | V | VDD = 5.0 | 5 |
| All other inputs Logic High input voltage | VAH | 2.1 | | | V | VDD = 3.0V | 5 |
| All other inputs Logic High input voltage | VAH | 3.5 | | | V | VDD = 5.0V | 5 |
| All other inputs Logic Low input voltage | VAL | | | 0.5 | V | VDD = 3.0V | 5 |
| All other inputs Logic Low input voltage | VAL | | | 1 | V | VDD = 5.0V | 5 |
| CNT_EN Low input current | IIEL | | 3 | 5 | µA | VAL = 0.7V, VDD = 3.0V | 5 |
| CNT_EN Low input current | IIEL | | 10 | 15 | µA | VAL = 1.2V, VDD = 5.0V | 5 |
| CNT_EN High input current | IIEH | | 1 | 3 | µA | VAH = 1.9V, VDD = 3.0V | 5 |
| CNT_EN High input current | IIEH | | 6 | 9 | µA | VAH = 3.2V, VDD = 5.0V | 5 |
| All other inputs, High or Low input current | | | 0 | 0 | µA | | 5 |
| LFLAG, DFLAG Sink output current | IOFL | -1.3 | -2 | | mA | VOUT = 0.5V, VDD = 3.0V | 5 |
| LFLAG, DFLAG Sink output current | IOFL | -3.2 | -4 | | mA | VOUT = 0.5V, VDD = 5.0V | 5 |
| LFLAG Source output current | | 0 | 0 | | mA | Open Drain Output | 5 |
| DFLAG Source output current | IOFH | 1 | 1.8 | | mA | VOUT = 2.5V, VDD = 3.0V | 5 |
| DFLAG Source output current | IOFH | 2.8 | 3.6 | | mA | VOUT = 4.5V, VDD = 5.0V | 5 |
| fCKO Sink output current | IOCL | -1.3 | -2 | | mA | VOUT = 0.5V, VDD = 3.0V | 5 |
| fCKO Sink output current | IOCL | -3.2 | -4 | | mA | VOUT = 0.5V, VDD = 5.0V | 5 |
| fCKO Source output current | IOCH | 1.3 | 2 | | mA | VOUT = 2.5V, VDD = 3.0V | 5 |
| fCKO Source output current | IOCH | 3.2 | 4 | | mA | VOUT = 4.5V, VDD = 5.0V | 5 |
| TXD/MISO Sink output current | IOML | -1.5 | -2.4 | | mA | VOUT = 0.5V, VDD = 3.0V | 5 |
| TXD/MISO Sink output current | IOML | -3.8 | -4.8 | | mA | VOUT = 0.5V, VDD = 5.0V | 5 |
| TXD/MISO Source output current | IOMH | 1.5 | 2.4 | | mA | VOUT = 2.5V, VDD = 3.0V | 5 |
| TXD/MISO Source output current | IOMH | 3.8 | 4.8 | | mA | VOUT = 4.5V, VDD = 5.0V | 5 |
| SCK High Pulse Width | tCH | 100 | | | ns | | 5 |
| SCK Low Pulse Width | tCL | 100 | | | ns | | 5 |
| SS/ Set Up Time | tCSL | 100 | | | ns | | 5 |
| SS/ Hold Time | tCSH | 100 | | | ns | | 5 |
| Inter Command SS/ high | tCSI | 100 | | | ns | | 5 |
| fCKI High Pulse Width | t1 | 12 | | | ns | | 5 |
| fCKI Pulse Width | t2 | 12 | | | ns | | 5 |
| fCKI Frequency | fFCK | | | 40 | MHz | | 5 |
| Effective Filter Clock fF Period | t3 | 25 | | | ns | t3 = t1+t2, MDR0 <7> = 0 | 5 |
| Effective Filter Clock fF Period | t3 | 50 | | | ns | t3 = 2(t1+t2), MDR0 <7> = 1 | 5 |
| Effective Filter Clock fF frequency | fF | | | 40 | MHz | fF = 1/ t3 | 5 |
| Quadrature Separation | t4 | 26 | | | ns | t4 > t3 | 5 |
| Quadrature Clock Pulse Width | t5 | 52 | | | ns | t5 2t3 | 5 |
| Quadrature Clock frequency | fQA, fQB | | | 9.6 | MHz | fQA = fQB < 1/4t3 | 5 |
| x1 / x2 / x4 Count Clock Pulse Width | tQ2 | 12 | | | ns | tQ2 = (t3)/2 | 5 |
| Index Input Pulse Width | tid | 32 | | | ns | tid > t4 | 5 |
| Index Set Up Time | tis | | | 5 | ns | | 5 |
| Index Hold Time | tih | | | 5 | ns | | 5 |
| DFLAG/ output width | tfw | 26 | | | ns | tfw = t4 | 5 |
| Clock A High Pulse Width | t6 | 12 | | | ns | | 6 |
| Clock A Low Pulse Width | t7 | 12 | | | ns | | 6 |
| Direction Input B Set-up Time | t8S | 12 | | | ns | | 6 |
| Direction Input B Hold Time | t8H | 10 | | | ns | | 6 |
| CNT_EN Set-up Time | t9S | 12 | | | ns | | 6 |
| CNT_EN Hold Time | t9H | 12 | | | ns | | 6 |
| Clock Frequency (non-Mod-N) | fA | | | 40 | MHz | fA = (1/(t6 + t7)) | 6 |
| Clock to DFLAG/ or LFLAG/ delay | t10 | 20 | | | ns | | 6 |
| DFLAG/ output width | t11 | 12 | | | ns | t10 = t7 | 6 |
## CAD (KiCad official)
- Symbol: `LS7366R-TS`
- Footprint: `Package_SO:TSSOP-14_4.4x5mm_P0.65mm`
- 3D model: TSSOP-14 (KiCad packages3D, STEP)
- 3D model files: `ls7366r-ts-etched.step` / `ls7366r-ts-etched.glb` carry the MPN laser-etched on the die in a toggleable `Adom.LaserEtch` group (Fusion-ready); `ls7366r-ts.step` / `ls7366r-ts.glb` are the bare package body.
## Provenance
Data extracted from the manufacturer datasheet, not a distributor listing:
- **Datasheet:** [LSI/CSI datasheet](docs/ls7366r-ts-datasheet.pdf) (17 pp, sha256 `51b1ffc0846b8ad0`, retrieved 2026-11-05, tier: lcsc)
- **Extractor:** parts-factory `2.0.0` / `extract_pins 0.3`, primary `claude-haiku-5-5` (text), consensus `claude-sonnet-5-5` (agreed), guards: pin_guards 0.1: passed. Pins are checked against the footprint pad set and their cited datasheet pages before publish.
- **CAD:** KiCad official libraries (CC-BY-SA 4.0).
[Datasheet PDF](docs/ls7366r-ts-datasheet.pdf)