Generated by kicad-footprint-generator · KiCad file format 20260206
LP8867QPWPRQ1
Texas Instruments · LED Drivers · HTSSOP-20-EP
LP8867QPWPRQ1 from Texas Instruments, in a HTSSOP-20-EP. Pinout and pin descriptions extracted from the manufacturer datasheet (extract_pins, cross-checked by a second model); symbol, footprint, and 3D from KiCad-official CAD.
Pinout
| Pin | Name | Type | Function |
|---|---|---|---|
| 1 | VIN | power_in | Input power pin, also the input voltage OVP detection pin and input current sense positive input. |
| 2 | LDO | power_out | Output of internal LDO; connect a 1-μF decoupling capacitor between this pin and noise-free ground, placed as close to the chip as possible. |
| 3 | FSET | passive | DC-DC switching frequency setting pin; a resistor from 24 kΩ to 219 kΩ must be connected between this pin and ground for normal operation. |
| 4 | VDDIO/EN | power_in | Enable input for the device as well as supply input (VDDIO) for the digital pins. |
| 5 | FAULT | output | Open-drain fault signal output; may be left floating if unused. |
| 6 | SYNC | input | Input for synchronizing the DC-DC converter; if unused, connect to ground to disable spread spectrum or to VDDIO/EN to enable spread spectrum. |
| 7 | PWM | input | PWM dimming input. |
| 8 | TSENSE | input | Input for NTC resistor divider for external temperature sensing; must be left floating if unused. |
| 9 | TSET | input | Input for NTC resistor divider for external temperature sensing; must be connected to GND if unused. |
| 10 | ISET | passive | LED current setting pin; a resistor from 20 kΩ to 129 kΩ must be connected between this pin and ground for normal operation. |
| 11 | GND | power_in | Ground. |
| 12 | OUT4 | passive | Current sink output 4 on LP8867-Q1 (GND pin on LP8869-Q1); must be connected to ground if not used. |
| 13 | OUT3 | passive | Current sink output 3; must be connected to ground if not used. |
| 14 | OUT2 | passive | Current sink output 2; must be connected to ground if not used. |
| 15 | OUT1 | passive | Current sink output 1; must be connected to ground if not used. |
| 16 | FB | input | DC-DC feedback input; connect to the middle of a resistor divider between VOUT and ground using feedback resistor values greater than 5 kΩ. |
| 17 | PGND | power_in | DC-DC (boost or SEPIC) power ground. |
| 18 | SW | passive | DC-DC (boost or SEPIC) switch pin. |
| 19 | SD | output | Power-line FET control, open-drain (current sink type) output; may be left floating if unused. |
| 20 | VSENSE_N | input | Input current sense negative input; connect to the VIN pin when an input current sense resistor is not used. |
| 21 | EP | passive | Exposed pad (from the footprint; not named in the datasheet pin table). |
Key specifications
| Parameter | Value |
|---|---|
| Manufacturer | Texas Instruments |
| Package | HTSSOP-20-EP |
| Category | Nixie Tube Driver/LED Driver |
| Pins | 21 |
Electrical characteristics
Limits as printed in the datasheet (page.json metadata.characteristics carries them as data).
| Parameter | Symbol | Min | Typ | Max | Unit | Conditions | Page |
|---|---|---|---|---|---|---|---|
| Standby supply current | IQ | 4.5 | 20 | μA | Device disabled, VVDDIO/EN = 0 V, VIN = 12 V | 6 | |
| Active supply current | IQ | 5 | 12 | mA | VIN = 12 V, VOUT = 26 V, output current 80 mA/channel, converter fSW = 300 kHz | 6 | |
| LDO output voltage | VLDO | 4.15 | 4.3 | 4.55 | V | VIN = 12 V | 6 |
| LDO dropout voltage | VDR | 120 | 300 | 430 | mV | 6 | |
| VIN OVP threshold voltage | VOVP | 41 | 42 | 44 | V | 6 | |
| VIN OCP threshold voltage, VIN - VSENSEN | VOCP | 135 | 160 | 186 | mV | 6 | |
| VIN UVLO falling threshold | VUVLO | 3.7 | 3.85 | 4 | V | 6 | |
| VSENSE_N pin leakage | ISENSE_N | 0.1 | 3 | µA | VSENSE_N = 45V, EN = L | 6 | |
| SD pin leakage | ISD_LEAK | 0.1 | 3 | µA | VSD = 45V, EN = L | 6 | |
| SD pull down current | ISD | 185 | 230 | 283 | µA | 6 | |
| Thermal shutdown rising threshold | TTSD | 150 | 165 | 175 | ℃ | 6 | |
| Current sink leakage current | ILEAKAGE | 0.1 | 5 | µA | Outputs OUT1 to OUT4, VOUTx = 45 V, EN = L | 7 | |
| Output current accuracy | IOUT | -5 | 5 | % | IOUT = 100 mA | 7 | |
| Output current matching | IMATCH | 1 | 5 | % | IOUT = 100 mA, PWM duty =100% | 7 | |
| High comparator threshold | VHIGH_COMP | 5.6 | 6 | 7 | V | 7 | |
| Maximum current | IMAX | 120 | mA | OUT1, OUT2, OUT3, OUT4, RISET = 20 kΩ | 7 | ||
| PWM input frequency | fPWM | 100 | 20000 | Hz | 7 | ||
| Boost converter input voltage | VIN | 4.5 | 40 | V | 7 | ||
| Boost converter output voltage | VOUT | 6 | 45 | V | 7 | ||
| Minimum switching frequency | fSW_MIN | 300 | kHz | Defined by RFSET resistor | 7 | ||
| Maximum switching frequency | fSW_MAX | 2200 | kHz | Defined by RFSET resistor | 7 | ||
| SW current limit first triggerred | ISW_MAX | 3.3 | 3.7 | 4.1 | A | 7 | |
| SW current limit | ISW_LIM | 3 | 3.35 | 3.7 | A | 7 | |
| FET RDSON | RDSON | 240 | 400 | mΩ | 7 | ||
| External SYNC frequency | fSYNC | 300 | 2200 | kHz | 7 | ||
| VDDIO/EN input low level | VIL | 0.4 | V | 7 | |||
| VDDIO/EN input high level | VIH | 1.65 | V | 7 | |||
| VDDIO/EN input DC current | IEN | -1 | 5 | 30 | µA | 7 | |
| SYNC/PWM input current | II | -1 | 1 | μA | 8 | ||
| FAULT output low level | VOL | 0.3 | 0.5 | V | Pullup current 3 mA | 8 | |
| FAULT output leakage current | ILEAKAGE | 1 | μA | V = 5.5 V | 8 | ||
| Voltage on VIN, VSENSE_N, SD, SW, FB | -0.3 | 50 | V | 5 | |||
| Voltage on OUT1-OUT4 | -0.3 | 45 | V | 5 | |||
| Voltage on LDO, SYNC, FSET, ISET, TSENSE, TSET, PWM, VDDIO/EN, FAULT | -0.3 | 5.5 | V | 5 | |||
| Ambient temperature | TA | -40 | 125 | °C | 5 | ||
| Junction temperature | TJ | -40 | 150 | °C | 5 | ||
| Storage temperature | Tstg | -65 | 150 | °C | 5 | ||
| HBM ESD | V(ESD) | -2000 | 2000 | V | HBM per AEC Q100-002, all pins | 5 | |
| CDM ESD corner pins | V(ESD) | -750 | 750 | V | Corner pins (1, 10, 11 and 20) | 5 | |
| CDM ESD all pins | V(ESD) | -500 | 500 | V | All pins | 5 | |
| VIN voltage | VIN | 4.5 | 12 | 45 | V | 5 | |
| SW, VSENSE_N, SD voltage | 0 | 45 | V | 5 | |||
| OUT1-OUT4 voltage | 0 | 40 | V | 5 | |||
| FB, FSET, LDO, ISET, TSENSE, TSET, VDDIO/EN, FAULT voltage | 0 | 5.25 | V | 5 | |||
| Junction-to-ambient thermal resistance | RθJA | 44.2 | °C/W | PWP (HTSSOP) 20 pins | 6 | ||
| Junction-to-case (top) thermal resistance | RθJCtop | 26.5 | °C/W | 6 | |||
| Junction-to-board thermal resistance | RθJB | 22.4 | °C/W | 6 | |||
| Junction-to-top characterization parameter | ψJT | 0.9 | °C/W | 6 | |||
| Junction-to-board characterization parameter | ψJB | 22.2 | °C/W | 6 | |||
| Junction-to-case (bottom) thermal resistance | RθJCbot | 2.5 | °C/W | 6 |
CAD (KiCad official)
- Symbol:
LP8867QPWPRQ1 - Footprint:
Package_SO:TSSOP-20-1EP_4.4x6.5mm_P0.65mm_EP2.15x3.35mm - 3D model: HTSSOP-20-EP, generated from the KiCad footprint (body from the F.Fab outline, terminals on the pads, 1.2 mm nominal TSSOP height). Neither the vendor nor KiCad ships a 3D model for this package, so the dimensions are nominal, not the manufacturer's CAD (STEP)
- 3D model files:
lp8867qpwprq1-etched.step/lp8867qpwprq1-etched.glbcarry the MPN laser-etched on the die in a toggleableAdom.LaserEtchgroup (Fusion-ready);lp8867qpwprq1.step/lp8867qpwprq1.glbare the bare package body.
Provenance
Data extracted from the manufacturer datasheet, not a distributor listing:
- Datasheet: Texas Instruments datasheet (44 pp, sha256
4ed821b4063c8430, retrieved 2026-10-22, tier: lcsc) - Extractor: parts-factory
2.0.0/extract_pins 0.3, primaryclaude-sonnet-5-5(text), consensusclaude-sonnet-5-5(agreed), guards: pin_guards 0.1: passed. Pins are checked against the footprint pad set and their cited datasheet pages before publish. - CAD: KiCad official libraries (CC-BY-SA 4.0).