Generated by kicad-footprint-generator · KiCad file format 20260206
LP5569ARTWR
Texas Instruments · LED Drivers · WQFN-24-EP(4x4)
LP5569ARTWR from Texas Instruments, in a WQFN-24-EP(4x4). Pinout and pin descriptions extracted from the manufacturer datasheet (extract_pins, cross-checked by a second model); symbol, footprint, and 3D from KiCad-official CAD.
Pinout
| Pin | Name | Type | Function |
|---|---|---|---|
| 1 | C2+ | passive | Positive pin of charge-pump flying capacitor 2; must be left floating if the charge pump is not used. |
| 2 | C1+ | passive | Positive pin of charge-pump flying capacitor 1; must be left floating if the charge pump is not used. |
| 3 | VIN | power_in | Input power (2.5 V to 5.5 V); a 1-µF capacitor must be connected between PGND and this pin. |
| 4 | AGND | power_in | Analog and digital ground; connect to PGND, exposed thermal pad, and common ground plane. |
| 5 | EN/PWM | input | Chip enable and PWM input pin. |
| 6 | CLK | bidirectional | Clock input/output (open-drain), a clock input by default; if not used it must be connected to GND or VIN. |
| 7 | GPIO/TRIG/INT | bidirectional | General-purpose input or open-drain output, trigger input or open-drain output, or interrupt open-drain output configured in I2C registers; defaults to open-drain general-purpose output and can be left floating if not used. |
| 8 | SDA | bidirectional | I2C bus data line (open-drain); if not used it must be connected to GND or VIN. |
| 9 | SCL | input | I2C bus clock line; if not used it must be connected to GND or VIN. |
| 10 | V1P8 | power_in | Input power for digital circuitry (1.65 V to 1.95 V recommended). |
| 11 | LED8 | passive | LED current sink 8; can be left floating if not used. |
| 12 | LED7 | passive | LED current sink 7; can be left floating if not used. |
| 13 | LED6 | passive | LED current sink 6; can be left floating if not used. |
| 14 | LED5 | passive | LED current sink 5; can be left floating if not used. |
| 15 | LED4 | passive | LED current sink 4; can be left floating if not used. |
| 16 | LED3 | passive | LED current sink 3; can be left floating if not used. |
| 17 | LED2 | passive | LED current sink 2; can be left floating if not used. |
| 18 | LED1 | passive | LED current sink 1; can be left floating if not used. |
| 19 | LED0 | passive | LED current sink 0; can be left floating if not used. |
| 20 | ADDR | input | I2C slave-address selection pin; must not be left floating. |
| 21 | PGND | power_in | Charge-pump power ground; connect to AGND, exposed thermal pad, and common ground plane. |
| 22 | VOUT | passive | Charge-pump output voltage; a 1-µF capacitor to PGND is required if the charge pump is used, and can be omitted if unused or in 1× mode only. |
| 23 | C2- | passive | Negative pin of charge-pump flying capacitor 2; must be left floating if the charge pump is not used. |
| 24 | C1- | passive | Negative pin of charge-pump flying capacitor 1; must be left floating if the charge pump is not used. |
| 25 | Exposed thermal pad | power_in | Must be connected to AGND (pin 4), PGND (pin 21), and common ground plane, and soldered for power dissipation and mechanical reliability. |
Key specifications
| Parameter | Value |
|---|---|
| Manufacturer | Texas Instruments |
| Package | WQFN-24-EP(4x4) |
| Category | Nixie Tube Driver/LED Driver |
| Pins | 25 |
Electrical characteristics
Limits as printed in the datasheet (page.json metadata.characteristics carries them as data).
| Parameter | Symbol | Min | Typ | Max | Unit | Conditions | Page |
|---|---|---|---|---|---|---|---|
| Voltage on VIN, CLK, ADDR, EN/PWM, GPIO/TRIG/INT, SCL, SDA, VOUT | -0.3 | 6 | V | 5 | |||
| Voltage on LED0 to LED8, C1-, C2-, C1+, C2+ | -0.3 | 6 | V | VVIN + 0.3 V with 6 V max | 5 | ||
| Voltage on V1P8 | -0.3 | 2 | V | 5 | |||
| Junction temperature | TJ-MAX | -40 | 125 | °C | 5 | ||
| Storage temperature | Tstg | -65 | 150 | °C | 5 | ||
| ESD HBM | V(ESD) | -2500 | 2500 | V | ANSI/ESDA/JEDEC JS-001 | 5 | |
| ESD CDM | V(ESD) | -250 | 250 | V | JESD22-C101 | 5 | |
| Input voltage on VIN | VVIN | 2.5 | 5.5 | V | 5 | ||
| Voltage on LED0 to LED8, C1-, C2-, C1+, C2+, VOUT | 0 | V | max is VVIN | 5 | |||
| Voltage on CLK, ADDR, EN/PWM, GPIO/TRIG/INT, SDA, SCL | 0 | V | max is VVIN | 5 | |||
| Input voltage on V1P8 | V1P8 | 1.65 | 1.95 | V | 5 | ||
| Output current on VOUT | 0 | 160 | mA | 5 | |||
| Operating ambient temperature | TA | -40 | 85 | °C | 5 | ||
| Junction-to-ambient thermal resistance | RθJA | 35.8 | °C/W | RTW (WQFN) 24 pins | 5 | ||
| Junction-to-case (top) thermal resistance | RθJC(top) | 26.7 | °C/W | 5 | |||
| Junction-to-board thermal resistance | RθJB | 13.1 | °C/W | 5 | |||
| Junction-to-top characterization parameter | ψJT | 0.4 | °C/W | 5 | |||
| Junction-to-board characterization parameter | ψJB | 13.1 | °C/W | 5 | |||
| Junction-to-case (bottom) thermal resistance | RθJC(bot) | 4.6 | °C/W | 5 | |||
| VIN standby supply current | IVIN | 0.2 | 1 | µA | VEN/PWM = 0 V, chip_en (bit) = 0 | 6 | |
| VIN standby supply current | IVIN | 1 | 2 | µA | VEN/PWM = 3.3 V, chip_en (bit) = 0, external CLK not running | 6 | |
| VIN standby supply current | IVIN | 2 | 4 | µA | VEN/PWM = 3.3 V, chip_en (bit) = 0, external CLK running | 6 | |
| VIN normal-mode supply current | IVIN | 56 | 70 | µA | External CLK running, charge pump and current sinks disabled | 6 | |
| VIN normal-mode supply current | IVIN | 65 | 90 | µA | Charge pump in 1× mode, no load, current sinks disabled | 6 | |
| VIN normal-mode supply current | IVIN | 1.8 | mA | Charge pump in 1.5× mode, no load, current-sink outputs disabled | 6 | ||
| VIN power-save mode supply current | IVIN | 10 | 15 | µA | External CLK running, see Automatic Power-Save Mode | 6 | |
| V1P8 standby supply current | IV1P8 | 0.2 | 1 | µA | VEN/PWM = 0 V, chip_en(bit) = 0 | 6 | |
| V1P8 standby supply current | IV1P8 | 0.2 | 2 | µA | VEN/PWM = 3.3 V, chip_en (bit) = 0, external CLK not running | 6 | |
| V1P8 standby supply current | IV1P8 | 1 | 4 | µA | VEN/PWM = 3.3 V, chip_en (bit) = 0, external CLK running | 6 | |
| V1P8 normal-mode supply current | IV1P8 | 174 | 190 | µA | External CLK running, charge pump and current sinks disabled | 6 | |
| V1P8 normal-mode supply current | IV1P8 | 180 | µA | Charge pump in 1.5× mode, no load, current-sink outputs disabled | 6 | ||
| V1P8 power-save mode supply current | IV1P8 | 1 | 5 | µA | External CLK running | 6 | |
| 32-kHz internal oscillator frequency accuracy | ƒOSC | -10 | 10 | % | TA = 25°C | 6 | |
| 10-MHz internal oscillator frequency accuracy | ƒOSC | -7 | 7 | % | 6 | ||
| Undervoltage lockout | VUVLO | 2.2 | V | VVIN falling | 6 | ||
| Undervoltage lockout | VUVLO | 2.3 | V | VVIN rising | 6 | ||
| Charge-pump output voltage | VOUT | 4.41 | 4.5 | 4.59 | V | VVIN = 3.7 V, IOUT = 160 mA, gain = 1.5× | 6 |
| Charge-pump output resistance | ROUT | 1 | Ω | Gain = 1×, VVIN = 4.2 V | 6 | ||
| Charge-pump output resistance | ROUT | 3.5 | Ω | Gain = 1.5×, VVIN = 3.7 V | 6 | ||
| Switching frequency | ƒSW | 1.25 | MHz | 6 | |||
| Output current limit | ICL | 600 | mA | VOUT = 0 V, VVIN = 3.7 V, CP_CONFIG = 0xFF | 6 | ||
| Maximum output current | IOUT | 200 | mA | VVIN > 3.1 V, VOUT dropped 10%, gain = 1.5× | 6 | ||
| Maximum output current | IOUT | 150 | mA | VIN > 2.5 V, VOUT dropped 10%, gain = 1.5× | 6 | ||
| Maximum sink current | IMAX | 24.5 | 25.5 | 26.5 | mA | 7 | |
| Sink current accuracy | ILED_ACC | -4.5 | 4.5 | % | Current set to 17.5 mA. PWM = 100% | 7 | |
| Matching | ILED_MATCH | 1 | 2.5 | % | Current set to 17.5 mA | 7 | |
| Saturation voltage | VSAT | 90 | 110 | mV | Output current set to 25.5 mA | 7 | |
| Leakage current (LED0 to LED8) | ILEAKAGE | 1 | µA | PWM = 0%, VLED = 5 V | 7 | ||
| LED switching frequency | ƒLED | 19.5 | kHz | 7 | |||
| Input low level (EN/PWM, SCL, ADDR) | VIL | 0.4 | V | 7 | |||
| Input high level (EN/PWM, SCL, ADDR) | VIH | 1.25 | V | 7 | |||
| Input leakage current (EN/PWM, SCL, ADDR) | Ilkg | -1 | 1 | µA | VI ≤ VVIN | 7 | |
| Input low level (SDA, GPIO/TRIG/INT, CLK) | VIL | 0.4 | V | Pin configured as input | 7 | ||
| Input high level (SDA, GPIO/TRIG/INT, CLK) | VIH | 1.25 | V | Pin configured as input | 7 | ||
| Input leakage current (SDA, GPIO/TRIG/INT, CLK) | Ilkg | -1 | 1 | µA | Pin configured as input, VVIN = 5.5 V, VI ≤ VVIN | 7 | |
| Output low level | VOL | 0.2 | 0.5 | V | IPULLUP = 3 mA | 7 | |
| Output leakage current | IL | 1 | µA | Pin configured as output, Hi-Z state | 7 | ||
| I2C clock frequency | ƒSCL | 0 | 400 | kHz | I2C fast mode | 8 |
CAD (KiCad official)
- Symbol:
LP5569ARTWR - Footprint:
Package_DFN_QFN:QFN-24-1EP_4x4mm_P0.5mm_EP2.6x2.6mm - 3D model: WQFN-24-EP(4x4) (KiCad packages3D, STEP)
- 3D model files:
lp5569artwr-etched.step/lp5569artwr-etched.glbcarry the MPN laser-etched on the die in a toggleableAdom.LaserEtchgroup (Fusion-ready);lp5569artwr.step/lp5569artwr.glbare the bare package body.
Provenance
Data extracted from the manufacturer datasheet, not a distributor listing:
- Datasheet: Texas Instruments datasheet (93 pp, sha256
ebce5fc0c509be9a, retrieved 2026-10-27, tier: lcsc) - Datasheet language: Chinese. Pin names, descriptions, and specs on this page were extracted and translated to English by ds2sf; the linked PDF is the manufacturer original.
- Extractor: parts-factory
2.0.0/extract_pins 0.3, primaryclaude-sonnet-5-5(text), consensusclaude-sonnet-5-5(agreed), guards: pin_guards 0.1: passed. Pins are checked against the footprint pad set and their cited datasheet pages before publish. - CAD: KiCad official libraries (CC-BY-SA 4.0).