main
Download ZIP Propose a change
Generated by kicad-footprint-generator · KiCad file format 20260206
Name Last commit message Last updated
docs Publish 0.1.0 · Ray
viewers lp4076espf: viewers · Ray
lp4076espf-etched.glb Publish 0.1.0 · Ray
lp4076espf-etched.step lp4076espf: factory component page (tier=lcsc) · Ray
lp4076espf-hero.glb lp4076espf: hero GLB from the etched model (keeps the MPN mark) · Ray
lp4076espf-hero.overlay.json Publish 0.1.0 · Ray
lp4076espf.glb Publish 0.1.0 · Ray
lp4076espf.kicad_mod Publish 0.1.0 · Ray
lp4076espf.kicad_sym Publish 0.1.0 · Ray
lp4076espf.lbr Publish 0.1.0 · Ray
lp4076espf.step Publish 0.1.0 · Ray
package.json Publish 0.1.0 · Ray
page.json Set visibility: public · Ray
README.md Publish 0.1.0 · Ray

LP4076ESPF

LOWPOWER(微源半导体) · Battery Management · ESOP-8

LP4076ESPF from LOWPOWER(微源半导体), in a ESOP-8. Pinout and pin descriptions extracted from the manufacturer datasheet (extract_pins, cross-checked by a second model); symbol, footprint, and 3D from KiCad-official CAD.

Pinout

Pin Name Type Function
1 TS input Battery temperature sense thermistor input that compares the TS voltage against the VIN-referenced hot threshold (30% VIN) and cold threshold (60% VIN), suspending charge when the battery temperature is out of range.
2 ISET input Fast charge current program pin, connected to GND through an external resistor RISET where ICC = 1V × 1700 / RISET, with better than 1% precision recommended for RISET; the pin voltage is limited to 0.3V to 6.5V absolute maximum.
3 GND power_in Ground; connect to the system ground.
4 IN power_in Positive supply input with 4.5V to 6V recommended operating voltage and 36V absolute maximum rating, requiring a 4.7Ω resistor and a 1-10µF ceramic capacitor in series from IN to GND placed as close to the IC as possible.
5 BAT power_out Battery connection that charges the single-cell Li-Ion or Li-Polymer battery, with a 1-10µF capacitor typically needed and a -5V to 14V absolute maximum rating to GND.
6 FULL output Open-drain status output that is pulled low by an internal NMOS when the charge cycle is complete and is high-impedance while charging, with a -0.3V to 28V absolute maximum rating to GND.
7 CHRG output Open-drain charge status output that is pulled low by an internal NMOS (about 5mA sink) while charging and is high-impedance when charging is terminated, with a -0.3V to 28V absolute maximum rating to GND.
8 EN input Active-low charge enable input for the LP4076ESPF: a level below 0.4V or a floating pin enables charging, a level above 1.4V puts the device in shutdown, and the absolute maximum rating is 6.5V to GND.
9 PAD power_in Exposed thermal pad that serves as the ground reference for the device and conducts heat to the PCB; adding vias under it helps lower the maximum junction temperature.

Key specifications

Parameter Value
Manufacturer LOWPOWER(微源半导体)
Package ESOP-8
Category Power Management (PMIC)
Pins 9

Electrical characteristics

Limits as printed in the datasheet (page.json metadata.characteristics carries them as data).

Parameter Symbol Min Typ Max Unit Conditions Page
VIN Input Voltage Range VIN 4.5 5 6 V 5
Under Voltage Lockout of VIN VUVLO 3.3 3.5 3.7 V VIN Rising 5
Over-Voltage Protection Threshold Voltage VOVP 6.7 7 7.3 V VIN Rising 5
Regulated Output Voltage VFLOAT 4.179 4.2 4.242 V 5
Fast Charge Current ICC 460 500 540 mA RISET=3.4kΩ, Constant Current Mode 5
Fast Charge Current ICC 90 100 110 mA RISET=17kΩ, Constant Current Mode 5
Trickle Charge Threshold Voltage VTRIKL 2.75 2.9 3.05 V VBAT Rising 5
Battery Recharge Voltage Difference Threshold (VFLOAT - VRECHRG) ΔVRECHRG 100 150 200 mV VBAT Falling 5
VIN-VBAT threshold Voltage VHeadroom 80 115 150 mV VBAT=3.7V, VIN Rising 5
EN pin leakage current IEN -1 1 μA VEN=5V or VEN=0V 6
NTC threshold (Hot) VNTC_H 28 30 32 % VIN VNTC_H falling, percentage to VIN 6
NTC threshold (Cold) VNTC_C 58 60 62 % VIN VNTC_C rising, percentage to VIN 6
Input Voltage VIN 4.5 6 V 4
Maximum Charge Current 1 A 4
Operating Junction Temperature Range (TJ) TJ 20 140 ℃ 4
Operating Ambient Temperature Range (TA) TA -20 85 ℃ 4
IN to GND VIN -0.3 36 V 4
CHRG, FULL to GND -0.3 28 V 4
BAT to GND VBAT -5 14 V 4
EN, ISET, TS to GND 0.3 6.5 V 4
Maximum Junction Temperature (TJ) TJ 150 ℃ 4
Storage Temperature TSTG -55 150 ℃ 4
Maximum Soldering Temperature 260 ℃ at leads, 10 sec 4
ESD Susceptibility HBM 2 kV Human Body Model 4
ESD Susceptibility MM 200 V Machine Model 4

CAD (KiCad official)

  • Symbol: LP4076ESPF
  • Footprint: Package_SO:SOIC-8-1EP_3.9x4.9mm_P1.27mm_EP2.41x3.3mm
  • 3D model: ESOP-8 (KiCad packages3D, STEP)
  • 3D model files: lp4076espf-etched.step / lp4076espf-etched.glb carry the MPN laser-etched on the die in a toggleable Adom.LaserEtch group (Fusion-ready); lp4076espf.step / lp4076espf.glb are the bare package body.

Provenance

Data extracted from the manufacturer datasheet, not a distributor listing:

  • Datasheet: LOWPOWER(微源半导体) datasheet (16 pp, sha256 7b569ec21d5a561a, retrieved 2026-11-07, tier: lcsc)
  • Extractor: parts-factory 2.0.0 / extract_pins 0.3, primary claude-haiku-5-5 (text), consensus claude-sonnet-5-5 (agreed), guards: pin_guards 0.1: passed. Pins are checked against the footprint pad set and their cited datasheet pages before publish.
  • CAD: KiCad official libraries (CC-BY-SA 4.0).

Datasheet PDF