3D Model
Open in new tab ↗
Loads when you scroll to it. Unloads after 5 minutes in the background.
Symbol & Footprint
Schematic Symbol
Open full view ↗Loads when you scroll to it. Unloads after 5 minutes in the background.
PCB Footprint
Open full view ↗Loads when you scroll to it. Unloads after 5 minutes in the background.
Datasheet
Open in new tab ↗Loads when you scroll to it. Unloads after 5 minutes in the background.
README
markdownLP3872EMP-2.5
Texas Instruments · Linear Voltage Regulators (LDO) · SOT-223-5
LP3872EMP-2.5 from Texas Instruments, in a SOT-223-5. Pinout and pin descriptions extracted from the manufacturer datasheet (extract_pins, cross-checked by a second model); symbol, footprint, and 3D from KiCad-official CAD.
Pinout
| Pin | Name | Type | Function |
|---|---|---|---|
| 1 | SD | input | Shutdown pin; must be pulled high through a 10-kΩ pullup resistor, and the part draws typically 10-nA quiescent current when SD is pulled low. |
| 2 | IN | input | Input supply pin; operates from a 2.5-V to 7-V input supply, with VIN maximum of 7 V and absolute maximum of 7.5 V. |
| 3 | GND | power_in | Ground pin; reference for the IN, SD, OUT and ERROR/SENSE pin voltage ratings. |
| 4 | OUT | power_out | Regulated output voltage pin; ensured output current of 1.5 A DC, short-circuit protected. |
| 5 | ERROR/SENSE | passive | Pin 5 function is ambiguous in the pin table: ERROR flag (LP3872) goes low when the output drops 10% below nominal, or remote voltage SENSE (LP3875); confirm against the datasheet. |
Key specifications
| Parameter | Value |
|---|---|
| Manufacturer | Texas Instruments |
| Package | SOT-223-5 |
| Category | Power Supply Chip |
| Pins | 5 |
Electrical characteristics
Limits as printed in the datasheet (page.json metadata.characteristics carries them as data).
| Parameter | Symbol | Min | Typ | Max | Unit | Conditions | Page |
|---|---|---|---|---|---|---|---|
| Output voltage tolerance | VOUT | -1.5 | 0 | 1.5 | % | VOUT +1 V ≤ VIN ≤ 7 V, 10 mA ≤ IL ≤ 1.5 A | 5 |
| Output voltage tolerance over temperature | VOUT | -3 | 3 | % | VOUT +1 V ≤ VIN ≤ 7 V, 10 mA ≤ IL ≤ 1.5 A, -40°C ≤ TJ ≤ 125°C | 5 | |
| Dropout voltage | VIN-VOUT | 38 | 50 | mV | IL = 150 mA | 5 | |
| Dropout voltage over temperature | VIN-VOUT | 60 | mV | IL = 150 mA, -40°C ≤ TJ ≤ 125°C | 5 | ||
| Dropout voltage | VIN-VOUT | 380 | 450 | mV | IL = 1.5 A | 5 | |
| Dropout voltage over temperature | VIN-VOUT | 550 | mV | IL = 1.5 A, -40°C ≤ TJ ≤ 125°C | 5 | ||
| Ground pin current in normal operation mode | IGND | 5 | 9 | mA | IL = 150 mA | 5 | |
| Ground pin current in normal operation mode over temperature | IGND | 10 | mA | IL = 150 mA, -40°C ≤ TJ ≤ 125°C | 5 | ||
| Ground pin current in normal operation mode | IGND | 6 | 14 | mA | IL = 1.5 A | 5 | |
| Ground pin current in normal operation mode over temperature | IGND | 15 | mA | IL = 1.5 A, -40°C ≤ TJ ≤ 125°C | 5 | ||
| Ground pin current in shutdown mode | IGND | 0.01 | 10 | µA | VSD ≤ 0.3 V | 5 | |
| Ground pin current in shutdown mode over temperature | IGND | 50 | µA | -40°C ≤ TJ ≤ 85°C | 5 | ||
| Peak output current | IO(PK) | 1.8 | A | VOUT ≥ VO(NOM), 4% | 5 | ||
| Short-circuit current | ISC | 3.2 | A | 5 | |||
| Shutdown threshold, output high | VSDT | 2 | V | Output = High, -40°C ≤ TJ ≤ 125°C | 5 | ||
| Shutdown threshold, output low | VSDT | 0 | V | Output = Low | 5 | ||
| Shutdown threshold, output low over temperature | VSDT | 0.3 | V | Output = Low, -40°C ≤ TJ ≤ 125°C | 5 | ||
| Turnoff delay | TdOFF | 20 | µs | IL = 1.5 A | 5 | ||
| Turnon delay | TdON | 25 | µs | IL = 1.5 A | 5 | ||
| SD input current | ISD | 1 | nA | VSD = VIN | 5 | ||
| ERROR flag threshold | VT | 10 | % of VOUT | See ERROR Flag Operation | 5 | ||
| ERROR flag threshold over temperature | VT | 5 | 16 | % of VOUT | -40°C ≤ TJ ≤ 125°C | 5 | |
| ERROR flag threshold hysteresis | VTH | 5 | % of VOUT | See ERROR Flag Operation | 5 | ||
| ERROR flag threshold hysteresis over temperature | VTH | 2 | 8 | % of VOUT | -40°C ≤ TJ ≤ 125°C | 5 | |
| ERROR flag saturation voltage | VEF(Sat) | 0.02 | V | Isink = 100 µA | 5 | ||
| ERROR flag saturation voltage over temperature | VEF(Sat) | 0.1 | V | Isink = 100 µA, -40°C ≤ TJ ≤ 125°C | 5 | ||
| Flag reset delay | Td | 1 | µs | 5 | |||
| ERROR flag pin leakage current | Ilk | 1 | nA | 5 | |||
| ERROR flag pin sink current | Imax | 1 | mA | VError = 0.5 V | 5 | ||
| Ripple rejection | PSRR | 73 | dB | VIN = VOUT + 1 V, COUT = 10 µF, VOUT = 3.3 V, f = 120 Hz | 6 | ||
| Ripple rejection | PSRR | 57 | dB | VIN = VOUT + 0.5 V, COUT = 10 µF, VOUT = 3.3 V, f = 120 Hz | 6 | ||
| Output noise voltage | en | 150 | µV | BW = 10 Hz, 100 kHz, VOUT = 2.5 V | 6 | ||
| Input supply voltage | VIN | 2.5 | 7 | V | 4 | ||
| Shutdown (SD) voltage | VSD | -0.3 | 7 | V | 4 | ||
| Maximum operating current (DC) | IOUT | 1.5 | A | 4 | |||
| Junction temperature | TJ | -40 | 125 | °C | 4 | ||
| Lead temperature (soldering, 5 sec.) | 260 | °C | soldering, 5 sec. | 4 | |||
| IN pin to GND pin voltage | VIN | -0.3 | 7.5 | V | 4 | ||
| Shutdown (SD) pin to GND pin voltage | VSD | -0.3 | 7.5 | V | 4 | ||
| OUT pin to GND pin voltage | VOUT | -0.3 | 6 | V | 4 | ||
| Storage temperature | Tstg | -65 | 150 | °C | 4 | ||
| ESD human body model | V(ESD) | -2000 | 2000 | V | Human body model (HBM), per ANSI/ESDA/JEDEC JS-001 | 4 | |
| Junction-to-ambient thermal resistance (SOT-223, NDC) | RθJA | 65.2 | °C/W | NDC (SOT-223) 5 pins | 4 | ||
| Junction-to-case (top) thermal resistance (SOT-223, NDC) | RθJC(top) | 47.2 | °C/W | NDC (SOT-223) 5 pins | 4 | ||
| Junction-to-board thermal resistance (SOT-223, NDC) | RθJB | 9.9 | °C/W | NDC (SOT-223) 5 pins | 4 | ||
| Junction-to-top characterization parameter (SOT-223, NDC) | ψJT | 3.4 | °C/W | NDC (SOT-223) 5 pins | 4 | ||
| Junction-to-board characterization parameter (SOT-223, NDC) | ψJB | 9.7 | °C/W | NDC (SOT-223) 5 pins | 4 |
CAD (KiCad official)
- Symbol:
LP3872EMP-2.5 - Footprint:
Package_TO_SOT_SMD:SOT-223-5 - 3D model: SOT-223-5 (KiCad packages3D, STEP)
- 3D model files:
lp3872emp-2-5-etched.step/lp3872emp-2-5-etched.glbcarry the MPN laser-etched on the die in a toggleableAdom.LaserEtchgroup (Fusion-ready);lp3872emp-2-5.step/lp3872emp-2-5.glbare the bare package body.
Provenance
Data extracted from the manufacturer datasheet, not a distributor listing:
- Datasheet: Texas Instruments datasheet (29 pp, sha256
2f9a4693db342387, retrieved 2026-10-28, tier: manufacturer) - Extractor: parts-factory
2.0.0/extract_pins 0.3, primaryclaude-haiku-5-5(text), consensusclaude-sonnet-5-5(agreed), guards: pin_guards 0.1: passed. Pins are checked against the footprint pad set and their cited datasheet pages before publish. - CAD: KiCad official libraries (CC-BY-SA 4.0).