Generated by kicad-footprint-generator · KiCad file format 20260206
LMX2522LQ1635
Texas Instruments · Clock Generators / Frequency Synthesizers / PLL · WQFN-28(5x5)
LMX2522LQ1635 from Texas Instruments, in a WQFN-28(5x5). Pinout and pin descriptions extracted from the manufacturer datasheet (extract_pins, cross-checked by a second model); symbol, footprint, and 3D from KiCad-official CAD.
Pinout
| Pin | Name | Type | Function |
|---|---|---|---|
| 1 | CPout | output | IF PLL charge pump output, used with the external IF VCO and loop filter; IF charge pump current is programmable at 100, 200, 300 or 800 µA. |
| 2 | NC | unconnected | Do not connect to any node on printed circuit board. |
| 3 | NC | unconnected | Do not connect to any node on printed circuit board. |
| 4 | VDD | power_in | Supply voltage for IF analog circuitry; VCC and VDD are specified at 2.7 V to 3.3 V. |
| 5 | LE | input | MICROWIRE Latch Enable; data in the shift register is loaded into the addressed control register on the LOW-to-HIGH transition of LE. |
| 6 | CLK | input | MICROWIRE Clock; serial DATA is clocked into the 24-bit shift register on the rising edge of CLK. |
| 7 | DATA | input | MICROWIRE Data input; data is loaded into the 24-bit shift register from MSB to LSB. |
| 8 | VDD | power_in | Supply voltage for VCOs; VCC and VDD are specified at 2.7 V to 3.3 V. |
| 9 | NC | unconnected | Do not connect to any node on printed circuit board. |
| 10 | NC | unconnected | Do not connect to any node on printed circuit board. |
| 11 | NC | unconnected | Do not connect to any node on printed circuit board. |
| 12 | NC | unconnected | Do not connect to any node on printed circuit board. |
| 13 | VDD | power_in | Supply voltage for VCOs; VCC and VDD are specified at 2.7 V to 3.3 V. |
| 14 | VDD | power_in | Supply voltage for VCOs output buffer; VCC and VDD are specified at 2.7 V to 3.3 V. |
| 15 | RFout | output | Buffered VCO output; output power is set by the OB_CRL[1:0] control bits from -9 dBm (minimum) to 4 dBm (maximum). |
| 16 | VCC | power_in | Supply voltage for RF prescaler; VCC and VDD are specified at 2.7 V to 3.3 V. |
| 17 | VCC | power_in | Supply voltage for charge pump; VCC and VDD are specified at 2.7 V to 3.3 V. |
| 18 | VCC | power_in | Supply voltage for RF digital circuitry; VCC and VDD are specified at 2.7 V to 3.3 V. |
| 19 | LD | output | Lock Detect output for the RF PLL; it is HIGH when locked and LOW when not locked, and is held at GND when disabled through the RF_LD bit. |
| 20 | CE | input | Chip Enable control pin; taking CE LOW powers the device down regardless of register values. |
| 21 | GND | power_in | Ground for digital circuitry. |
| 22 | OSCin | input | Reference frequency input; 19.20 MHz and 19.68 MHz are supported, with reference oscillator input sensitivity listed as 0.2 VCC Vp-p. |
| 23 | VCC | power_in | Supply voltage for reference input buffer; VCC and VDD are specified at 2.7 V to 3.3 V. |
| 24 | GND | power_in | Ground for digital circuitry. |
| 25 | VCC | power_in | Supply voltage for IF digital circuitry; VCC and VDD are specified at 2.7 V to 3.3 V. |
| 26 | Fin | input | IF buffer/prescaler input; IF input sensitivity is -10 dBm to 0 dBm. |
| 27 | VCC | power_in | Supply voltage for IF buffer/prescaler; VCC and VDD are specified at 2.7 V to 3.3 V. |
| 28 | NC | unconnected | Do not connect to any node on printed circuit board. |
| 29 | EP | passive | Exposed pad (from the footprint; not named in the datasheet pin table). |
Key specifications
| Parameter | Value |
|---|---|
| Manufacturer | Texas Instruments |
| Package | WQFN-28(5x5) |
| Category | RTC/Clock Chip |
| Pins | 29 |
Electrical characteristics
Limits as printed in the datasheet (page.json metadata.characteristics carries them as data).
| Parameter | Symbol | Min | Typ | Max | Unit | Conditions | Page |
|---|---|---|---|---|---|---|---|
| Ambient Temperature | TA | -30 | 25 | 85 | °C | 4 | |
| Supply Voltage (to VCC, VDD GND) | VCC, VDD | 2.7 | 3.3 | V | 4 | ||
| Supply Voltage | VCC, VDD | -0.3 | 3.6 | V | 4 | ||
| Voltage on any pin VI to VDD | VI | -0.3 | V | to VDD (printed upper limit VDD+0.3 V) | 4 | ||
| Voltage on any pin VI to GND | VI | -0.3 | V | to GND (printed upper limit VCC+0.3 V) | 4 | ||
| Storage Temperature Range | TSTG | -65 | 150 | °C | 4 | ||
| ICC + IDD Total Supply Current | ICC + IDD | 17 | 19 | mA | OB_CRL [1:0] = 00 | 4 | |
| (ICC + IDD)RF RF PLL Total Supply Current | (ICC + IDD)RF | 16 | 18 | mA | OB_CRL [1:0] = 00 | 4 | |
| Power Down Current | IPD | 20 | µA | CE = Low or RF_EN = 0, IF_EN = 0 | 4 | ||
| Reference Oscillator Input Frequency | fOSCin | 19.2 | 19.68 | MHz | 19.20 MHz and 19.68 MHz are supported | 4 | |
| Reference Oscillator Input sensitivity | VOSCin | 0.2 | VP-P | printed upper limit 0.2 VCC | 4 | ||
| Frequency Range RF VCO | fRFout | 1619.62 | 1649.62 | MHz | LMX2522LQ1635 RF VCO | 5 | |
| RF Output Power | pRFout | -2 | 1 | 4 | dBm | OB_CRL [1:0] = 11 | 5 |
| RF Output Power | pRFout | -5 | -2 | 1 | dBm | OB_CRL [1:0] = 10 | 5 |
| RF Output Power | pRFout | -7 | -4 | -1 | dBm | OB_CRL [1:0] = 01 | 5 |
| RF Output Power | pRFout | -9 | -6 | -3 | dBm | OB_CRL [1:0] = 00 | 5 |
| Lock Time RF PLL | 500 | 800 | µs | LMX2522LQ1635 30 MHz Band for RF PLL | 5 | ||
| Reference Spurs RF PLL | -75 | dBc | 5 | ||||
| RMS Phase Error | 1.3 | degrees | RF PLL in all band | 5 | |||
| L(f) Phase Noise | L(f) | -113 | -112 | dBc/Hz | LMX2522LQ1635 @100 kHz offset | 5 | |
| L(f) Phase Noise | L(f) | -138 | -136 | dBc/Hz | LMX2522LQ1635 @1.25 MHz offset | 5 | |
| 2nd Harmonic Suppression | -25 | dBc | RF VCO | 5 | |||
| 3rd Harmonic Suppression | -20 | dBc | RF VCO | 5 | |||
| Output Power GPS VCO | pRFout | -2 | 1 | 4 | dBm | OB_CRL [1:0] = 11 | 5 |
| Output Power GPS VCO | pRFout | -5 | -2 | 1 | dBm | OB_CRL [1:0] = 10 | 5 |
| Output Power GPS VCO | pRFout | -7 | -4 | -1 | dBm | OB_CRL [1:0] = 01 | 5 |
| Output Power GPS VCO | pRFout | -9 | -6 | -3 | dBm | OB_CRL [1:0] = 00 | 5 |
| Lock Time From RF to GPS PLL | 600 | 800 | µs | 5 | |||
| Reference Spurs GPS VCO | -75 | dBc | 5 | ||||
| RMS Phase Error (GPS section) | 1.3 | degrees | RF PLL in all band | 5 | |||
| L(f) Phase Noise GPS VCO | L(f) | -113 | -112 | dBc/Hz | @100 kHz offset | 5 | |
| L(f) Phase Noise GPS VCO | L(f) | -138 | -136 | dBc/Hz | @1.25 MHz offset | 5 | |
| 2nd Harmonic Suppression GPS VCO | -25 | dBc | 5 | ||||
| 3rd Harmonic Suppression GPS VCO | -20 | dBc | 5 | ||||
| IF Input Sensitivity | pFin | -10 | 0 | dBm | 6 | ||
| High-Level Input Current | IIH | -10 | 10 | µA | 6 | ||
| Low-Level Input Current | IIL | -10 | 10 | µA | 6 | ||
| Low-Level Input Voltage | VIL | 0 | V | printed upper limit 0.2 VDD (or 0.2 VCC) | 6 | ||
| Data to Clock Set Up Time | tCS | 50 | ns | 6 | |||
| Data to Clock Hold Time | tCH | 10 | ns | 6 | |||
| Clock Pulse Width High | tCWH | 50 | ns | 6 | |||
| Clock Pulse Width Low | tCWL | 50 | ns | 6 | |||
| Clock to Latch Enable Set Up Time | tES | 50 | ns | 6 | |||
| Latch Enable Pulse Width | tEW | 50 | ns | 6 | |||
| Operating Frequency GPS VCO | fRFout | 1355.04 | MHz | LMX2522LQ1635 GPS VCO | 5 | ||
| Operating Frequency | fFin | 440.76 | MHz | LMX2522LQ1635, IF_FREQ [1:0] = 10 (Default Value) | 6 | ||
| Phase Detector Frequency | fΦIF | 120 | kHz | 6 | |||
| Charge Pump Current | ICPout | 100 | µA | IF_CUR [1:0] = 00 | 6 | ||
| Charge Pump Current | ICPout | 200 | µA | IF_CUR [1:0] = 01 | 6 | ||
| Charge Pump Current | ICPout | 300 | µA | IF_CUR [1:0] = 10 | 6 | ||
| Charge Pump Current | ICPout | 800 | µA | IF_CUR [1:0] = 11 | 6 | ||
| Input Capacitance | 3 | pF | 6 | ||||
| Output Capacitance | 5 | pF | 6 |
CAD (KiCad official)
- Symbol:
LMX2522LQ1635 - Footprint:
Package_DFN_QFN:QFN-28-1EP_5x5mm_P0.5mm_EP3.35x3.35mm - 3D model: WQFN-28(5x5) (KiCad packages3D, STEP)
- 3D model files:
lmx2522lq1635-etched.step/lmx2522lq1635-etched.glbcarry the MPN laser-etched on the die in a toggleableAdom.LaserEtchgroup (Fusion-ready);lmx2522lq1635.step/lmx2522lq1635.glbare the bare package body.
Provenance
Data extracted from the manufacturer datasheet, not a distributor listing:
- Datasheet: Texas Instruments datasheet (25 pp, sha256
68785d44d531575e, retrieved 2026-10-31, tier: manufacturer) - Extractor: parts-factory
2.0.0/extract_pins 0.3, primaryclaude-haiku-5-5(text), consensusclaude-sonnet-5-5(agreed), guards: pin_guards 0.1: passed. Pins are checked against the footprint pad set and their cited datasheet pages before publish. - CAD: KiCad official libraries (CC-BY-SA 4.0).