main
Ray Publish 0.1.0 57a1d68

LMR51606XFQDBVRQ1

Texas Instruments · IC · SOT-23-6

LMR51606XFQDBVRQ1 from Texas Instruments, in a SOT-23-6. Pinout and pin descriptions extracted from the manufacturer datasheet (extract_pins, cross-checked by a second model); symbol, footprint, and 3D from KiCad-official CAD.

Pinout

Pin Name Type Function
1 CB passive Bootstrap capacitor connection for the high-side FET driver; connect a high-quality 100nF capacitor from this pin to the SW pin.
2 GND power_in Power ground pins connected internally to the source of the low-side FET; connect to system ground and the ground side of CIN and COUT, with the path to CIN kept as short as possible.
3 FB input Feedback input to the converter; a resistor divider sets the output voltage, and this terminal must never be shorted to ground during operation.
4 EN input Precision enable input where High = On and Low = Off; it must not float, can be tied to VIN, and allows an adjustable UVLO set by an external resistor divider.
5 VIN power_in Supply input to the internal bias LDO and high-side FET; input bypass capacitors CIN must be connected directly to this pin and GND.
6 SW power_out Switching output of the converter, internally connected to the source of the high-side FET and the drain of the low-side FET; connect to the power inductor.

Key specifications

Parameter Value
Manufacturer Texas Instruments
Package SOT-23-6
Category
Pins 6

Electrical characteristics

Limits as printed in the datasheet (page.json metadata.characteristics carries them as data).

Parameter Symbol Min Typ Max Unit Conditions Page
Input voltage VIN to GND VIN -0.3 70 V 4
Input voltage EN to GND EN -0.3 V max printed as VIN + 0.3 V 4
Input voltage FB to GND FB -0.3 5.5 V 4
Output voltage SW to GND SW -0.3 70 V 4
Output voltage SW to GND transient SW -5 70 V less than 10ns transients 4
Output voltage CBOOT to SW CBOOT -0.3 5.5 V 4
Junction temperature TJ -40 150 °C 4
Storage temperature Tstg -55 150 °C 4
Input voltage VIN to GND VIN 4 65 V 4
Input voltage EN EN 0 V max printed as VIN 4
Input voltage FB FB 0 4.5 V 4
Output voltage VOUT VOUT 0.8 28 V 4
Output current Iout (LMR51606-Q1) Iout 0.6 A 4
Operating junction temperature TJ -40 150 °C 4
VIN operating input voltage range VIN 4 65 V 6
VIN UVLO rising threshold VIN_ UVLO(R) 3.82 4 V VIN rising 5
VIN UVLO falling threshold VIN_ UVLO(F) 3.4 3.56 V VIN falling 5
EN voltage rising threshold VEN(R) 1.1 1.227 1.36 V EN rising, enable switching 5
EN voltage falling threshold VEN(F) 0.85 1 1.15 V EN falling, disable switching 5
EN pin sourcing current post EN rising threshold IEN(P2) 10 50 nA VEN = 3V 5
Reference voltage VFB 0.792 0.8 0.808 V 5
Switching frequency, CCM operation fSW(CCM) 360 400 440 KHz 5
High-side peak current limit (LMR51606-Q1) IHS_PK(OC) 0.8 1.1 1.4 A LMR51606-Q1 6
Low-side valley current limit (LMR51606-Q1) ILS_V(OC) 0.62 0.8 0.98 A LMR51606-Q1 6
VIN shutdown supply current ISD(VIN) 0.8 3 µA VEN = 0V 5
Maximum switch duty cycle DMAX 96 % 6
VIN quiescent current IQ(VIN) 420 µA VEN = 3V, FPWM operation 5
VIN UVLO hysteresis VIN_ UVLO(H) 0.25 V 5
FB input leakage current IFB(LKG) 0.2 nA VFB = 0.8V 5
Internal fixed soft-start time tSS 2.3 ms 5
High-side MOSFET on-resistance RDSON(HS) 0.7 Ω VIN = 12V, TJ = 25°C 5
Low-side MOSFET on-resistance RDSON(LS) 0.36 Ω VIN = 12V, TJ = 25°C 5
Minimum ON pulse width tON_MIN 80 ns VIN = 12V, IOUT = 0.1A 5
Maximum ON pulse width tON_MAX 5 µs VIN = 12V, IOUT = 0.5A 5
Minimum OFF pulse width tOFF_MIN 200 ns VIN = 5V 5
Low-side negative current limit (LMR51606-Q1) ILS(NOC) -0.36 A LMR51606-Q1 FPWM Only 6
Zero-cross detection current threshold IZC 0 A 6
Thermal shutdown threshold TJ(SD) 165 °C Junction temperature rising 6
Thermal shutdown hysteresis TJ(HYS) 20 °C 6
FB voltage to trip short-circuit hiccup mode VHC 0.32 V 6
Time between current-limit hiccup burst THICCUP 150 ms 6
Junction-to-ambient thermal resistance RθJA 147.8 °C/W 5
Junction-to-ambient thermal resistance with EVM RθJA(Effective) 67.2 °C/W with EVM 5
Junction-to-case (top) thermal resistance RθJC(top) 71.1 °C/W 5
Junction-to-board thermal resistance RθJB 36.6 °C/W 5
Junction-to-top characterization parameter ψJT 14.2 °C/W 5
Junction-to-board characterization parameter ψJB 36.4 °C/W 5

Materials and finish

As the datasheet states them (page.json metadata.appearance; the 3D model's colours follow it).

Part Material Colour / plating Datasheet says Page
contacts copper The SW pin connecting to the inductor must be as short as possible, and just wide enough to carry the load current without excessive heating. Short, thick traces or copper pours (shapes) must be used 21

CAD (KiCad official)

  • Symbol: LMR51606XFQDBVRQ1
  • Footprint: Package_TO_SOT_SMD:SOT-23-6
  • 3D model: SOT-23-6 (KiCad packages3D, STEP)
  • 3D model files: lmr51606xfqdbvrq1-etched.step / lmr51606xfqdbvrq1-etched.glb carry the MPN laser-etched on the die in a toggleable Adom.LaserEtch group (Fusion-ready); lmr51606xfqdbvrq1.step / lmr51606xfqdbvrq1.glb are the bare package body.

Provenance

Data extracted from the manufacturer datasheet, not a distributor listing:

  • Datasheet: Texas Instruments datasheet (32 pp, sha256 21a1ad213c491448, retrieved 2026-11-02, tier: manufacturer)
  • Extractor: parts-factory 2.0.0 / extract_pins 0.3, primary claude-haiku-5-5 (text), consensus claude-sonnet-5-5 (agreed), guards: pin_guards 0.1: passed. Pins are checked against the footprint pad set and their cited datasheet pages before publish.
  • CAD: KiCad official libraries (CC-BY-SA 4.0).

Datasheet PDF