main
Ray lmr50410yfqdbvrq1: specified limits as data (metadata.characteristics, 43 rows from the datasheet) 7cb91c6

LMR50410YFQDBVRQ1

Texas Instruments · DC-DC Converters · SOT-23-6

LMR50410YFQDBVRQ1 from Texas Instruments, in a SOT-23-6. Pinout and pin descriptions extracted from the manufacturer datasheet by ds2sf; symbol, footprint, and 3D from KiCad-official CAD.

Pinout

Pin Name Type Function
1 CB output Bootstrap capacitor pin for high-side gate driver; connect 100-nF capacitor between this pin and SW.
2 GND power_in Power ground return path for internal FETs; connect to system ground and output capacitor return paths.
3 FB input Feedback input with 1.0V nominal reference voltage; connect resistor divider to set output voltage.
4 EN input Precision enable input; high level (>1.36V typical) enables and low level (<0.95V typical) disables converter, do not leave floating.
5 VIN power_in Input power supply terminal accepting 4V to 36V; connect input supply and bypass capacitors directly to this pin and GND.
6 SW output Switching output node connected to high-side FET source and low-side FET drain; connect to inductor for step-down conversion.

Key specifications

Parameter Value
Manufacturer Texas Instruments
Package SOT-23-6
Category Power Management (PMIC)
Pins 6

Electrical characteristics

Limits as printed in the datasheet (page.json metadata.characteristics carries them as data).

Parameter Symbol Min Typ Max Unit Conditions Page
Input voltage VIN to GND (absolute maximum) VIN -0.3 38 V 4
FB to GND (absolute maximum) -0.3 5.5 V 4
SW to GND (absolute maximum) -0.3 V 4
SW to GND less than 10-ns transients (absolute maximum) -3.5 38 V less than 10-ns transients 4
CB to SW (absolute maximum) -0.3 5.5 V 4
Junction temperature (absolute maximum) TJ -40 150 °C 4
Storage temperature (absolute maximum) Tstg -65 150 °C 4
Input voltage VIN to GND (recommended) VIN 4 36 V 4
EN to GND (recommended) 0 V 4
Output voltage VOUT (recommended) VOUT 1 28 V Maximum VOUT ensured up to 90% of VIN in final production 4
Output current (recommended) IOUT 0 1 A 4
Undervoltage lockout rising threshold VIN_UVLO 3.55 3.75 4 V 5
Undervoltage lockout falling threshold VIN_UVLO 3.25 3.45 3.65 V 5
Enable input high-level for VOUT VEN-VOUT-H 1.1 1.23 1.36 V VENABLE rising 5
Enable input low-level for VOUT VEN-VOUT-L 0.95 1.1 1.22 V VENABLE falling 5
Enable input leakage current ILKG-EN 10 200 nA VEN = 3.3V 5
Shutdown quiescent current measured at VIN pin ISD 3 10 µA VEN = 0 V 5
Feedback voltage VFB 0.99 1 1.01 V 5
High-side current limit ISC 1.25 1.6 1.9 A Vin=12V 5
Low-side current limit ILS-LIMIT 0.9 1.1 1.3 A Vin=12V 5
Internal oscillator frequency FOSC 1.8 2.1 2.4 MHz 2.1-MHz variant 6
Adjustable output voltage regulation (FPWM operation) VOUT -1.5 1.5 % Deviation from nominal VOUT at VIN = 24 V, IOUT = 0 A to full load 6
Maximum switch duty cycle DMAX 98 % 6
Undervoltage lockout hysteresis 0.3 V 5
Enable input hysteresis for VOUT VEN-VOUT-HYS 130 mV Hysteresis 5
Feedback leakage current ILKG-FB 0.2 nA FB = 1.2 V 5
Negative current limit (FPWM variant only) IL-NEG -0.6 A 5
High-side MOSFET ON-resistance RDS-ON-HS 450 mΩ TJ=25 ℃, VIN = 12 V 5
Low-side MOSFET ON-resistance RDS-ON-LS 240 mΩ TJ=25 ℃, VIN = 12 V 5
Thermal shutdown rising threshold TSD-Rising 170 °C Shutdown threshold 5
Thermal shutdown falling (recovery) threshold TSD-Falling 158 °C Recovery threshold 6
Minimum switch on-time tON-MIN 60 ns IOUT=1A 6
Minimum switch off-time tOFF-MIN 110 ns IOUT=1A 6
Maximum switch on-time tON-MAX 7.5 µs 6
Internal soft-start time tSS 1.8 ms 6
Time between current-limit hiccup burst tHC 135 ms 6
FB pin voltage required to trip short-circuit hiccup mode VHC 0.4 V 6
Switch voltage dead time tD 2 ns 6
Junction-to-ambient thermal resistance RθJA 173 °C/W JESD 51-7, simulated on 4-layer JEDEC board 4
Junction-to-case (top) thermal resistance RθJC(top) 116 °C/W JESD 51-7, simulated on 4-layer JEDEC board 4
Junction-to-board thermal resistance RθJB 31 °C/W JESD 51-7, simulated on 4-layer JEDEC board 4
Junction-to-top characterization parameter ψJT 20 °C/W JESD 51-7, simulated on 4-layer JEDEC board 4
Junction-to-board characterization parameter ψJB 30 °C/W JESD 51-7, simulated on 4-layer JEDEC board 5

CAD (KiCad official)

  • Symbol: LMR50410YFQDBVRQ1
  • Footprint: Package_TO_SOT_SMD:SOT-23-6
  • 3D model: SOT-23-6 (KiCad packages3D, STEP)
  • 3D model files: lmr50410yfqdbvrq1-etched.step / lmr50410yfqdbvrq1-etched.glb carry the MPN laser-etched on the die in a toggleable Adom.LaserEtch group (Fusion-ready); lmr50410yfqdbvrq1.step / lmr50410yfqdbvrq1.glb are the bare package body.

Provenance

Data extracted from the manufacturer datasheet, not a distributor listing:

  • Datasheet: Texas Instruments datasheet (38 pp, sha256 65ab961f308f6fad, retrieved 2026-09-23, tier: lcsc)
  • Datasheet language: Chinese. Pin names, descriptions, and specs on this page were extracted and translated to English by ds2sf; the linked PDF is the manufacturer original.
  • Extractor: parts-factory 2.0.0 / extract_pins 0.2, primary claude-haiku-4-5-20251001 (text), consensus claude-sonnet-5 (agreed), guards: pin_guards 0.1: passed. Pins are checked against the footprint pad set and their cited datasheet pages before publish.
  • CAD: KiCad official libraries (CC-BY-SA 4.0).

Datasheet PDF