main
Ray
Publish 0.1.0
8e0d0fa
LMR38020FSQDDARQ1
Texas Instruments · DC-DC Converters · SOP-8
LMR38020FSQDDARQ1 from Texas Instruments, in a SOP-8. Pinout and pin descriptions extracted from the manufacturer datasheet (extract_pins, cross-checked by a second model); symbol, footprint, and 3D from KiCad-official CAD.
Pinout
| Pin | Name | Type | Function |
|---|---|---|---|
| 1 | GND | power_in | Power and analog ground terminal; all electrical parameters are measured with respect to this pin, and a high-quality bypass capacitor should connect directly to this pin and VIN with short and wide traces. |
| 2 | EN | input | Enable input to the regulator, high = ON and low = OFF, which can be connected directly to VIN and must not be left floating. |
| 3 | VIN | power_in | Input supply to the regulator, which operates from 4.2 V to 80 V after start-up and requires a high-quality bypass capacitor connected directly to this pin and GND with short and wide traces. |
| 4 | RT/SYNC | input | Resistor timing pin that sets the switching frequency from 200 kHz to 2.2 MHz with an internal amplifier holding a fixed voltage, or an external clock input for synchronization when pulled above the PLL upper threshold. |
| 5 | FB | input | Feedback input connected to the tap point of the feedback voltage divider, which must not be left floating or grounded. |
| 6 | PG | output | Open-drain power-good flag output that is high when power is OK and low when power is bad, pulls low when EN is low, and may be left open when not used. |
| 7 | BOOT | power_in | Bootstrap supply voltage for the internal high-side driver, which requires a high-quality 100-nF capacitor connected from this pin to the SW pin. |
| 8 | SW | power_out | Regulator switch node that connects to the power inductor and swings up to approximately VIN during high-side on time, with a maximum rating of 85 V to PGND. |
Key specifications
| Parameter | Value |
|---|---|
| Manufacturer | Texas Instruments |
| Package | SOP-8 |
| Category | Power Management |
| Pins | 8 |
Materials and finish
As the datasheet states them (page.json metadata.appearance; the 3D model's colours follow it).
| Part | Material | Colour / plating | Datasheet says | Page |
|---|---|---|---|---|
| contacts | copper | • Keep switch area small. Keep the copper area connecting the SW pin to the inductor as short and wide as | 28 |
CAD (KiCad official)
- Symbol:
LMR38020FSQDDARQ1 - Footprint:
Package_SO:SOIC-8_3.9x4.9mm_P1.27mm - 3D model: SOP-8 (KiCad packages3D, STEP)
- 3D model files:
lmr38020fsqddarq1-etched.step/lmr38020fsqddarq1-etched.glbcarry the MPN laser-etched on the die in a toggleableAdom.LaserEtchgroup (Fusion-ready);lmr38020fsqddarq1.step/lmr38020fsqddarq1.glbare the bare package body.
Provenance
Data extracted from the manufacturer datasheet, not a distributor listing:
- Datasheet: Texas Instruments datasheet (43 pp, sha256
f3e217a4218c6deb, retrieved 2026-11-02, tier: manufacturer) - Extractor: parts-factory
2.0.0/extract_pins 0.3, primaryclaude-haiku-5-5(text), consensusclaude-sonnet-5-5(agreed), guards: pin_guards 0.1: passed. Pins are checked against the footprint pad set and their cited datasheet pages before publish. - CAD: KiCad official libraries (CC-BY-SA 4.0).
# LMR38020FSQDDARQ1
**Texas Instruments** · DC-DC Converters · SOP-8
LMR38020FSQDDARQ1 from Texas Instruments, in a SOP-8. Pinout and pin descriptions extracted from the manufacturer datasheet (extract_pins, cross-checked by a second model); symbol, footprint, and 3D from KiCad-official CAD.
## Pinout
| Pin | Name | Type | Function |
|---|---|---|---|
| 1 | GND | power_in | Power and analog ground terminal; all electrical parameters are measured with respect to this pin, and a high-quality bypass capacitor should connect directly to this pin and VIN with short and wide traces. |
| 2 | EN | input | Enable input to the regulator, high = ON and low = OFF, which can be connected directly to VIN and must not be left floating. |
| 3 | VIN | power_in | Input supply to the regulator, which operates from 4.2 V to 80 V after start-up and requires a high-quality bypass capacitor connected directly to this pin and GND with short and wide traces. |
| 4 | RT/SYNC | input | Resistor timing pin that sets the switching frequency from 200 kHz to 2.2 MHz with an internal amplifier holding a fixed voltage, or an external clock input for synchronization when pulled above the PLL upper threshold. |
| 5 | FB | input | Feedback input connected to the tap point of the feedback voltage divider, which must not be left floating or grounded. |
| 6 | PG | output | Open-drain power-good flag output that is high when power is OK and low when power is bad, pulls low when EN is low, and may be left open when not used. |
| 7 | BOOT | power_in | Bootstrap supply voltage for the internal high-side driver, which requires a high-quality 100-nF capacitor connected from this pin to the SW pin. |
| 8 | SW | power_out | Regulator switch node that connects to the power inductor and swings up to approximately VIN during high-side on time, with a maximum rating of 85 V to PGND. |
## Key specifications
| Parameter | Value |
|---|---|
| Manufacturer | Texas Instruments |
| Package | SOP-8 |
| Category | Power Management |
| Pins | 8 |
## Materials and finish
As the datasheet states them (page.json `metadata.appearance`; the 3D model's colours follow it).
| Part | Material | Colour / plating | Datasheet says | Page |
|---|---|---|---|---|
| contacts | copper | | • Keep switch area small. Keep the copper area connecting the SW pin to the inductor as short and wide as | 28 |
## CAD (KiCad official)
- Symbol: `LMR38020FSQDDARQ1`
- Footprint: `Package_SO:SOIC-8_3.9x4.9mm_P1.27mm`
- 3D model: SOP-8 (KiCad packages3D, STEP)
- 3D model files: `lmr38020fsqddarq1-etched.step` / `lmr38020fsqddarq1-etched.glb` carry the MPN laser-etched on the die in a toggleable `Adom.LaserEtch` group (Fusion-ready); `lmr38020fsqddarq1.step` / `lmr38020fsqddarq1.glb` are the bare package body.
## Provenance
Data extracted from the manufacturer datasheet, not a distributor listing:
- **Datasheet:** [Texas Instruments datasheet](https://www.ti.com/lit/ds/symlink/lmr38020-q1.pdf?ts=1695215350757&ref_url=https%253A%252F%252Fwww.ti.com%252Fsitesearch%252Fen-us%252Fdocs%252Funiversalsearch.tsp%253FlangPref%253Den-US%2526searchTerm%253DLMR38020FSQDDARQ1%2526nr%253D4) (43 pp, sha256 `f3e217a4218c6deb`, retrieved 2026-11-02, tier: manufacturer)
- **Extractor:** parts-factory `2.0.0` / `extract_pins 0.3`, primary `claude-haiku-5-5` (text), consensus `claude-sonnet-5-5` (agreed), guards: pin_guards 0.1: passed. Pins are checked against the footprint pad set and their cited datasheet pages before publish.
- **CAD:** KiCad official libraries (CC-BY-SA 4.0).
[Datasheet PDF](docs/lmr38020fsqddarq1-datasheet.pdf)