main
History Download
Ray Publish 0.1.0 3f3eecb

LMR38010FDDAR

Texas Instruments · DC-DC Converters · SO-PowerPAD-8

LMR38010FDDAR from Texas Instruments, in a SO-PowerPAD-8. Pinout and pin descriptions extracted from the manufacturer datasheet (extract_pins, cross-checked by a second model). The symbol is generated from that pin table, the footprint is an Adom_Gen land derived from the manufacturer drawing, and the 3D model is generated to fit it.

Pinout

Pin Name Type Function
1 GND power_in Power and analog ground terminal; all electrical parameters are measured with respect to this pin, and a high-quality bypass capacitor should connect directly to this pin and VIN with short and wide traces.
2 EN input Enable input to the regulator with High = ON and low = OFF; it can be connected directly to VIN and must not be left floating.
3 VIN power_in Input supply to the regulator, with an input voltage range after start-up of 4.2 V to 80 V; connect a high-quality bypass capacitor directly to this pin and GND with short and wide traces.
4 RT/SYNC input Resistor timing or external clock input that sets the switching frequency with a resistor to ground, and becomes a synchronization input when pulled above the PLL upper threshold.
5 FB input Feedback input to the regulator that connects to the tap point of the feedback voltage divider and must not be floated or grounded.
6 PG output Open-drain power-good flag output that must be connected through a current limiting resistor to a supply, reading high for power OK and low for power bad, and it pulls low when EN is low.
7 BOOT power_out Bootstrap supply voltage for the internal high-side driver, which requires a high-quality 100-nF capacitor connected from this pin to the SW pin.
8 SW power_out Regulator switch node that connects to a power inductor and swings up to approximately VIN during high-side on time.
9 EP passive Exposed pad (from the footprint; not named in the datasheet pin table).

Key specifications

Parameter Value
Manufacturer Texas Instruments
Package SO-PowerPAD-8
Category Power Management (PMIC)
Pins 9

Electrical characteristics

Limits as printed in the datasheet (page.json metadata.characteristics carries them as data).

Parameter Symbol Min Typ Max Unit Conditions Page
Input voltage range after start-up VIN 4.2 80 V Input voltage range after start-up 4
Output voltage range for adjustable version VOUT 1 75 V Output voltage range for adjustable version 4
Output voltage SW to PGND SW 80 V SW to PGND 4
Frequency adjustment range fSW 200 2200 kHz Frequency adjustment range 4
Synchronization frequency range fSYNC 300 2100 kHz Synchronization frequency range 4
Output DC current range LMR38010 IOUT 0 1 A Output DC current range LMR38010 4
Operating junction temperature range TJ -40 150 °C Operating junction temperature TJ range 4
Input voltage PGOOD to PGND VPGOOD 20 V PGOOD to PGND 4
VIN to PGND VIN -0.3 85 V VIN to PGND 4
EN to PGND VEN -0.3 V EN to PGND; maximum VIN+0.3 4
FB to PGND VFB -0.3 5.5 V FB to PGND 4
RT/SYNC to PGND VRT/SYNC -0.3 5.5 V RT/SYNC to PGND 4
BOOT to SW VBOOT-SW -0.3 5.5 V BOOT to SW 4
SW to PGND VSW -0.3 85 V SW to PGND 4
SW to PGND transients VSW -5 85.3 V less than 10-ns transients 4
PGOOD to PGND VPGOOD -0.3 20 V PGOOD to PGND 4
Junction temperature TJ -40 150 °C Junction temperature TJ 4
Storage temperature Tstg -65 150 °C Storage temperature, Tstg 4
Input operating voltage (start-up) VIN_OPERATE 4.2 V Needed to start up 5
Input operating voltage (once operating) VIN_OPERATE 3.8 V Once operating 5
Enable input high level VEN-H 1.1 1.25 1.4 V VEN rising 5
Enable input low level VEN-L 0.95 1.1 1.22 V VEN falling 5
Enable input leakage current ILKG-EN 5 nA VEN = 3.3V 5
Feedback reference voltage VREF 0.99 1 1.01 V Vin=4.2V to 80V, TJ=25°C, FPWM 5
Feedback reference voltage VREF 0.985 1 1.015 V FPWM 5
High-side current limit IHS-LIMIT 1.3 1.6 1.9 A 1A Version 5
Low-side current limit ILS-LIMIT 0.9 1.2 1.5 A 1A Version 5
Negative current limit IL-NEG -0.5 A 1A Version, FPWM variant only 5
Switching frequency FOSC 430 525 650 kHz RT = 49.9 kΩ 5
SYNC clock high level threshold VSYNC_HI 2 V SYNC clock high level threshold 6
SYNC clock low level threshold VSYNC_LO 0.6 V SYNC clock low level threshold 6
Minimum switch on-time tON-MIN 80 131 ns VIN =24 V, Iout = 1 A 5
Minimum switch off-time tOFF-MIN 190 300 ns 5
Power-Good upper threshold - rising VPG-HIGH-UP 110 112 114 % rising % of FB voltage 6
Power-Good lower threshold - falling VPG-LOW-DN 90 92 94 % falling % of FB voltage 6
Spread of internal oscillator (FPWM variant tolerance of switching frequency maximum) DMAX 97 % Maximum switch duty cycle 7
VOUT adjustable output voltage regulation VOUT -1.5 1.5 % FPWM operation 7
Frequency span of spread spectrum operation FsSS -4 4 % Frequency span of spread spectrum operation 7
Minimum input voltage for proper Power-Good function VPG-VALID 2 V Minimum input voltage for proper Power-Good function 6
Shutdown quiescent current ISD 3 10 µA Measured at VIN pin VEN = 0 V 5
Power-Good hysteresis VPG-HYS 2.2 % Power-Good hysteresis (rising & falling) % of FB voltage 6
Power-Good on-resistance RPG 140 Ω VEN = 0 V 6
Power-Good on-resistance RPG 92 Ω VEN = 3.3V 6
High-side MOSFET ON-resistance RDS-ON-HS 303 mΩ 5
Low-side MOSFET ON-resistance RDS-ON-LS 133 mΩ 5
Maximum switch on-time tON-MAX 5 us 5
SYNC clock pulse high duration tPULSE_H 50 ns High duration needed to be recognized as a pulse 6
Internal soft-start time tSS 4 ms 6
Glitch filter time constant for PGOOD function tPGDFLT(fall) 40 us Glitch filter time constant for PGOOD function 6
Thermal shutdown threshold (rising) TSD-Rising 163 ℃ Shutdown threshold 6
Thermal shutdown recovery threshold (falling) TSD-Falling 150 ℃ Recovery threshold 6
FB pin voltage required to trip short-circuit hiccup mode VHC 0.4 V FB pin voltage required to trip short-circuit hiccup mode 7
Switch voltage dead time tD 5 ns Switch voltage dead time 7
Thermal shutdown temperature (shutdown) TSD 163 °C Shutdown temperature 7
Thermal shutdown temperature (recovery) TSD 150 °C Recovery temperature 7
Junction-to-ambient thermal resistance RθJA 42.9 °C/W 5
Junction-to-ambient thermal resistance with TI EVM board RθJA(Effecitve) 29 °C/W 5
Junction-to-case (top) thermal resistance RθJC(top) 54 °C/W 5
Junction-to-board thermal resistance RθJB 13.6 °C/W 5
Junction-to-top characterization parameter ψJT 4.3 °C/W 5
Junction-to-board characterization parameter ψJB 13.8 °C/W 5
Junction-to-case (bottom) thermal resistance RθJC(bot) 4.3 °C/W 5

Materials and finish

As the datasheet states them (page.json metadata.appearance; the 3D model's colours follow it).

Part Material Colour / plating Datasheet says Page
contacts copper • Keep switch area small. Keep the copper area connecting the SW pin to the inductor as short and wide as 27

CAD (Adom-generated)

  • Symbol: LMR38010FDDAR
  • Footprint: Adom_Gen:Texas_Instruments_LMR38010_89fb66
  • 3D model: generated to fit the land (STEP)
  • 3D model files: lmr38010fddar-etched.step / lmr38010fddar-etched.glb carry the MPN laser-etched on the die in a toggleable Adom.LaserEtch group (Fusion-ready); lmr38010fddar.step / lmr38010fddar.glb are the bare package body.

Provenance

Data extracted from the manufacturer datasheet, not a distributor listing:

  • Datasheet: Texas Instruments datasheet (40 pp, sha256 b8b6dced113ffb83, retrieved 2026-11-16, tier: manufacturer)
  • Extractor: parts-factory 2.0.0 / extract_pins 0.3, primary claude-haiku-5-5 (text), consensus claude-sonnet-5-5 (agreed), guards: pin_guards 0.1: passed. Pins are checked against the footprint pad set and their cited datasheet pages before publish.
  • CAD: symbol generated from the datasheet pin table; footprint an Adom_Gen land derived from the manufacturer drawing; 3D model generated to fit that land.

Datasheet PDF