Generated by adom_assets · KiCad file format 20240108
LMR38010FDDAR
Texas Instruments · DC-DC Converters · SO-PowerPAD-8
LMR38010FDDAR from Texas Instruments, in a SO-PowerPAD-8. Pinout and pin descriptions extracted from the manufacturer datasheet (extract_pins, cross-checked by a second model). The symbol is generated from that pin table, the footprint is an Adom_Gen land derived from the manufacturer drawing, and the 3D model is generated to fit it.
Pinout
| Pin | Name | Type | Function |
|---|---|---|---|
| 1 | GND | power_in | Power and analog ground terminal; all electrical parameters are measured with respect to this pin, and a high-quality bypass capacitor should connect directly to this pin and VIN with short and wide traces. |
| 2 | EN | input | Enable input to the regulator with High = ON and low = OFF; it can be connected directly to VIN and must not be left floating. |
| 3 | VIN | power_in | Input supply to the regulator, with an input voltage range after start-up of 4.2 V to 80 V; connect a high-quality bypass capacitor directly to this pin and GND with short and wide traces. |
| 4 | RT/SYNC | input | Resistor timing or external clock input that sets the switching frequency with a resistor to ground, and becomes a synchronization input when pulled above the PLL upper threshold. |
| 5 | FB | input | Feedback input to the regulator that connects to the tap point of the feedback voltage divider and must not be floated or grounded. |
| 6 | PG | output | Open-drain power-good flag output that must be connected through a current limiting resistor to a supply, reading high for power OK and low for power bad, and it pulls low when EN is low. |
| 7 | BOOT | power_out | Bootstrap supply voltage for the internal high-side driver, which requires a high-quality 100-nF capacitor connected from this pin to the SW pin. |
| 8 | SW | power_out | Regulator switch node that connects to a power inductor and swings up to approximately VIN during high-side on time. |
| 9 | EP | passive | Exposed pad (from the footprint; not named in the datasheet pin table). |
Key specifications
| Parameter | Value |
|---|---|
| Manufacturer | Texas Instruments |
| Package | SO-PowerPAD-8 |
| Category | Power Management (PMIC) |
| Pins | 9 |
Electrical characteristics
Limits as printed in the datasheet (page.json metadata.characteristics carries them as data).
| Parameter | Symbol | Min | Typ | Max | Unit | Conditions | Page |
|---|---|---|---|---|---|---|---|
| Input voltage range after start-up | VIN | 4.2 | 80 | V | Input voltage range after start-up | 4 | |
| Output voltage range for adjustable version | VOUT | 1 | 75 | V | Output voltage range for adjustable version | 4 | |
| Output voltage SW to PGND | SW | 80 | V | SW to PGND | 4 | ||
| Frequency adjustment range | fSW | 200 | 2200 | kHz | Frequency adjustment range | 4 | |
| Synchronization frequency range | fSYNC | 300 | 2100 | kHz | Synchronization frequency range | 4 | |
| Output DC current range LMR38010 | IOUT | 0 | 1 | A | Output DC current range LMR38010 | 4 | |
| Operating junction temperature range | TJ | -40 | 150 | °C | Operating junction temperature TJ range | 4 | |
| Input voltage PGOOD to PGND | VPGOOD | 20 | V | PGOOD to PGND | 4 | ||
| VIN to PGND | VIN | -0.3 | 85 | V | VIN to PGND | 4 | |
| EN to PGND | VEN | -0.3 | V | EN to PGND; maximum VIN+0.3 | 4 | ||
| FB to PGND | VFB | -0.3 | 5.5 | V | FB to PGND | 4 | |
| RT/SYNC to PGND | VRT/SYNC | -0.3 | 5.5 | V | RT/SYNC to PGND | 4 | |
| BOOT to SW | VBOOT-SW | -0.3 | 5.5 | V | BOOT to SW | 4 | |
| SW to PGND | VSW | -0.3 | 85 | V | SW to PGND | 4 | |
| SW to PGND transients | VSW | -5 | 85.3 | V | less than 10-ns transients | 4 | |
| PGOOD to PGND | VPGOOD | -0.3 | 20 | V | PGOOD to PGND | 4 | |
| Junction temperature | TJ | -40 | 150 | °C | Junction temperature TJ | 4 | |
| Storage temperature | Tstg | -65 | 150 | °C | Storage temperature, Tstg | 4 | |
| Input operating voltage (start-up) | VIN_OPERATE | 4.2 | V | Needed to start up | 5 | ||
| Input operating voltage (once operating) | VIN_OPERATE | 3.8 | V | Once operating | 5 | ||
| Enable input high level | VEN-H | 1.1 | 1.25 | 1.4 | V | VEN rising | 5 |
| Enable input low level | VEN-L | 0.95 | 1.1 | 1.22 | V | VEN falling | 5 |
| Enable input leakage current | ILKG-EN | 5 | nA | VEN = 3.3V | 5 | ||
| Feedback reference voltage | VREF | 0.99 | 1 | 1.01 | V | Vin=4.2V to 80V, TJ=25°C, FPWM | 5 |
| Feedback reference voltage | VREF | 0.985 | 1 | 1.015 | V | FPWM | 5 |
| High-side current limit | IHS-LIMIT | 1.3 | 1.6 | 1.9 | A | 1A Version | 5 |
| Low-side current limit | ILS-LIMIT | 0.9 | 1.2 | 1.5 | A | 1A Version | 5 |
| Negative current limit | IL-NEG | -0.5 | A | 1A Version, FPWM variant only | 5 | ||
| Switching frequency | FOSC | 430 | 525 | 650 | kHz | RT = 49.9 kΩ | 5 |
| SYNC clock high level threshold | VSYNC_HI | 2 | V | SYNC clock high level threshold | 6 | ||
| SYNC clock low level threshold | VSYNC_LO | 0.6 | V | SYNC clock low level threshold | 6 | ||
| Minimum switch on-time | tON-MIN | 80 | 131 | ns | VIN =24 V, Iout = 1 A | 5 | |
| Minimum switch off-time | tOFF-MIN | 190 | 300 | ns | 5 | ||
| Power-Good upper threshold - rising | VPG-HIGH-UP | 110 | 112 | 114 | % | rising % of FB voltage | 6 |
| Power-Good lower threshold - falling | VPG-LOW-DN | 90 | 92 | 94 | % | falling % of FB voltage | 6 |
| Spread of internal oscillator (FPWM variant tolerance of switching frequency maximum) | DMAX | 97 | % | Maximum switch duty cycle | 7 | ||
| VOUT adjustable output voltage regulation | VOUT | -1.5 | 1.5 | % | FPWM operation | 7 | |
| Frequency span of spread spectrum operation | FsSS | -4 | 4 | % | Frequency span of spread spectrum operation | 7 | |
| Minimum input voltage for proper Power-Good function | VPG-VALID | 2 | V | Minimum input voltage for proper Power-Good function | 6 | ||
| Shutdown quiescent current | ISD | 3 | 10 | µA | Measured at VIN pin VEN = 0 V | 5 | |
| Power-Good hysteresis | VPG-HYS | 2.2 | % | Power-Good hysteresis (rising & falling) % of FB voltage | 6 | ||
| Power-Good on-resistance | RPG | 140 | Ω | VEN = 0 V | 6 | ||
| Power-Good on-resistance | RPG | 92 | Ω | VEN = 3.3V | 6 | ||
| High-side MOSFET ON-resistance | RDS-ON-HS | 303 | mΩ | 5 | |||
| Low-side MOSFET ON-resistance | RDS-ON-LS | 133 | mΩ | 5 | |||
| Maximum switch on-time | tON-MAX | 5 | us | 5 | |||
| SYNC clock pulse high duration | tPULSE_H | 50 | ns | High duration needed to be recognized as a pulse | 6 | ||
| Internal soft-start time | tSS | 4 | ms | 6 | |||
| Glitch filter time constant for PGOOD function | tPGDFLT(fall) | 40 | us | Glitch filter time constant for PGOOD function | 6 | ||
| Thermal shutdown threshold (rising) | TSD-Rising | 163 | ℃ | Shutdown threshold | 6 | ||
| Thermal shutdown recovery threshold (falling) | TSD-Falling | 150 | ℃ | Recovery threshold | 6 | ||
| FB pin voltage required to trip short-circuit hiccup mode | VHC | 0.4 | V | FB pin voltage required to trip short-circuit hiccup mode | 7 | ||
| Switch voltage dead time | tD | 5 | ns | Switch voltage dead time | 7 | ||
| Thermal shutdown temperature (shutdown) | TSD | 163 | °C | Shutdown temperature | 7 | ||
| Thermal shutdown temperature (recovery) | TSD | 150 | °C | Recovery temperature | 7 | ||
| Junction-to-ambient thermal resistance | RθJA | 42.9 | °C/W | 5 | |||
| Junction-to-ambient thermal resistance with TI EVM board | RθJA(Effecitve) | 29 | °C/W | 5 | |||
| Junction-to-case (top) thermal resistance | RθJC(top) | 54 | °C/W | 5 | |||
| Junction-to-board thermal resistance | RθJB | 13.6 | °C/W | 5 | |||
| Junction-to-top characterization parameter | ψJT | 4.3 | °C/W | 5 | |||
| Junction-to-board characterization parameter | ψJB | 13.8 | °C/W | 5 | |||
| Junction-to-case (bottom) thermal resistance | RθJC(bot) | 4.3 | °C/W | 5 |
Materials and finish
As the datasheet states them (page.json metadata.appearance; the 3D model's colours follow it).
| Part | Material | Colour / plating | Datasheet says | Page |
|---|---|---|---|---|
| contacts | copper | • Keep switch area small. Keep the copper area connecting the SW pin to the inductor as short and wide as | 27 |
CAD (Adom-generated)
- Symbol:
LMR38010FDDAR - Footprint:
Adom_Gen:Texas_Instruments_LMR38010_89fb66 - 3D model: generated to fit the land (STEP)
- 3D model files:
lmr38010fddar-etched.step/lmr38010fddar-etched.glbcarry the MPN laser-etched on the die in a toggleableAdom.LaserEtchgroup (Fusion-ready);lmr38010fddar.step/lmr38010fddar.glbare the bare package body.
Provenance
Data extracted from the manufacturer datasheet, not a distributor listing:
- Datasheet: Texas Instruments datasheet (40 pp, sha256
b8b6dced113ffb83, retrieved 2026-11-16, tier: manufacturer) - Extractor: parts-factory
2.0.0/extract_pins 0.3, primaryclaude-haiku-5-5(text), consensusclaude-sonnet-5-5(agreed), guards: pin_guards 0.1: passed. Pins are checked against the footprint pad set and their cited datasheet pages before publish. - CAD: symbol generated from the datasheet pin table; footprint an Adom_Gen land derived from the manufacturer drawing; 3D model generated to fit that land.