Generated by adom_assets · KiCad file format 20240108
LMR36006BRNXR
Texas Instruments · DC-DC Converters · VQFN-12(2x3)
LMR36006BRNXR from Texas Instruments, in a VQFN-12(2x3). Pinout and pin descriptions extracted from the manufacturer datasheet (extract_pins, cross-checked by a second model). The symbol is generated from that pin table, the footprint is an Adom_Gen land derived from the manufacturer drawing, and the 3D model is generated to fit it.
Pinout
| Pin | Name | Type | Function |
|---|---|---|---|
| 1 | PGND | power_in | Power ground terminal; connect to system ground and AGND, using short wide traces to CIN. |
| 2 | VIN | power_in | Input supply to the regulator; connect to CIN with short wide traces. |
| 3 | NC | unconnected | Connect this pin to SW on the PCB; it has no internal connection to the regulator. |
| 4 | BOOT | power_out | Bootstrap supply for the internal high-side driver; connect a high-quality 100-nF capacitor from this pin to SW. |
| 5 | VCC | power_out | Internal 5-V LDO output used as supply for internal control circuits; do not connect to external loads and connect a high-quality 1-µF capacitor from this pin to GND. |
| 6 | AGND | power_in | Analog ground and reference for the regulator and system; all electrical parameters are measured with respect to this pin and it connects to system ground on the PCB. |
| 7 | FB | input | Feedback input connected to the tap point of the feedback voltage divider; do not float and do not ground. |
| 8 | PG | output | Open-drain power-good flag output connected to a supply through a current-limiting resistor; it goes low when EN is low and may be left open or grounded when unused. |
| 9 | EN | input | Enable input where high = ON and low = OFF; it can be connected directly to VIN but must not float. |
| 10 | VIN | power_in | Input supply to the regulator; connect to CIN with short wide traces. |
| 11 | PGND | power_in | Power ground terminal; connect to system ground and AGND, using short wide traces to CIN. |
| 12 | SW | power_out | Regulator switch node connected to the power inductor; connect it to pin 3 (NC) on the PCB. |
Key specifications
| Parameter | Value |
|---|---|
| Manufacturer | Texas Instruments |
| Package | VQFN-12(2x3) |
| Category | Power Supply Chip |
| Pins | 12 |
Electrical characteristics
Limits as printed in the datasheet (page.json metadata.characteristics carries them as data).
| Parameter | Symbol | Min | Typ | Max | Unit | Conditions | Page |
|---|---|---|---|---|---|---|---|
| Input voltage VIN to PGND | VIN | -0.3 | 66 | V | 5 | ||
| Input voltage EN to AGND | EN | -0.3 | 66.3 | V | 5 | ||
| Input voltage FB to AGND | FB | -0.3 | 5.5 | V | 5 | ||
| Input voltage PG to AGND | PG | -0.3 | 22 | V | 5 | ||
| Input voltage AGND to PGND | AGND-PGND | -0.3 | 0.3 | V | 5 | ||
| Output voltage SW to PGND | SW | -0.3 | 66.3 | V | 5 | ||
| Output voltage SW to PGND less than 10-ns transients | SW | -3.5 | 66.3 | V | less than 10-ns transients | 5 | |
| Output voltage CBOOT to SW | CBOOT-SW | -0.3 | 5.5 | V | 5 | ||
| Output voltage VCC to AGND | VCC | -0.3 | 5.5 | V | 5 | ||
| Junction temperature | TJ | -40 | 150 | °C | 5 | ||
| Storage temperature | Tstg | -65 | 150 | °C | 5 | ||
| Input voltage VIN to PGND (recommended) | VIN | 4.2 | 60 | V | 5 | ||
| EN to PGND (recommended) | EN | 0 | 60 | V | 5 | ||
| PG to PGND (recommended) | PG | 0 | 18 | V | 5 | ||
| Output current | IOUT | 0 | 0.6 | A | 5 | ||
| Operating junction temperature range | TJ | -40 | 150 | °C | Recommended operating junction temperature range | 5 | |
| Junction-to-ambient thermal resistance | RθJA | 72.5 | °C/W | RNX (VQFN-HR) 12 pins | 6 | ||
| Junction-to-case (top) thermal resistance | RθJC(top) | 35.9 | °C/W | RNX (VQFN-HR) 12 pins | 6 | ||
| Junction-to-board thermal resistance | RθJB | 23.3 | °C/W | RNX (VQFN-HR) 12 pins | 6 | ||
| Junction-to-top characterization parameter | ψJT | 0.8 | °C/W | RNX (VQFN-HR) 12 pins | 6 | ||
| Junction-to-board characterization parameter | ψJB | 23.5 | °C/W | RNX (VQFN-HR) 12 pins | 6 | ||
| Operating quiescent current (non-switching) | IQ-nonSW | 18 | 26 | 36 | µA | VEN = 3.3 V (PFM variant only) | 6 |
| Shutdown quiescent current measured at VIN pin | ISD | 5 | µA | VEN = 0 V | 6 | ||
| Enable input high level for VCC output | VEN-VCC-H | 1.14 | V | VENABLE rising | 6 | ||
| Enable input low level for VCC output | VEN-VCC-L | 0.3 | V | VENABLE falling | 6 | ||
| Enable input high level for VOUT | VEN-VOUT-H | 1.157 | 1.231 | 1.3 | V | VENABLE rising | 6 |
| Enable input hysteresis for VOUT | VEN-VOUT-HYS | 110 | mV | Hysteresis below VENABLE-H; falling | 6 | ||
| Enable input leakage current | ILKG-EN | 0.2 | nA | VEN = 3.3V | 6 | ||
| Internal VCC voltage | VCC | 4.75 | 5 | 5.25 | V | 6 V ≤ VIN ≤ 60 V | 6 |
| Internal VCC undervoltage lockout rising | VCC-UVLO-Rising | 3.6 | 3.8 | 4 | V | VCC rising | 6 |
| Internal VCC undervoltage lockout falling | VCC-UVLO-Falling | 3.1 | 3.3 | 3.5 | V | VCC falling | 6 |
| Feedback voltage | VFB | 0.985 | 1 | 1.015 | V | 6 | |
| Feedback leakage current | ILKG-FB | 0.2 | nA | FB = 1 V | 6 | ||
| High-side current limit | ISC | 0.8 | 1 | 1.2 | A | 6 | |
| Low-side current limit | ILS-LIMIT | 0.6 | 0.8 | 0.95 | A | 6 | |
| Zero cross detector threshold | IL-ZC | 0.02 | A | PFM variants only | 6 | ||
| Minimum inductor peak current | IPEAK-MIN | 0.18 | A | 6 | |||
| Power-Good upper threshold rising | VPG-HIGH-UP | 105 | 107 | 110 | % | % of FB voltage | 7 |
| Power-Good lower threshold falling | VPG-LOW-DN | 90 | 93 | 95 | % | % of FB voltage | 7 |
| Power-Good hysteresis rising and falling | VPG-HYS | 2 | % | % of FB voltage | 7 | ||
| Power-Good rising/falling edge deglitch delay | TPG | 80 | 140 | 200 | µs | 7 | |
| Minimum input voltage for proper Power-Good function | VPG-VALID | 2 | V | 7 | |||
| Power-Good on-resistance | RPG | 80 | 165 | Ω | VEN = 2.5 V | 7 | |
| Power-Good on-resistance | RPG | 35 | 90 | Ω | VEN = 0 V | 7 | |
| Internal oscillator frequency 1-MHz variant | FOSC | 0.85 | 1 | 1.15 | MHz | 1-MHz variant | 7 |
| High-side MOSFET ON-resistance | RDS-ON-HS | 225 | 435 | mΩ | IOUT = 0.5 A | 7 | |
| Low-side MOSFET ON-resistance | RDS-ON-LS | 150 | 280 | mΩ | IOUT = 0.5 A | 7 | |
| Minimum switch on-time | tON-MIN | 55 | 83 | ns | 7 | ||
| Minimum switch off-time | tOFF-MIN | 53 | 73 | ns | 7 | ||
| Maximum switch on-time | tON-MAX | 7 | 12 | µs | 7 | ||
| Internal soft-start time | tSS | 3 | 4.5 | 6 | ms | 7 | |
| Operating input voltage range | VIN | 4.2 | 60 | V | 8 | ||
| Adjustable output voltage regulation | VOUT | -1.5 | 2.5 | % | PFM operation | 8 | |
| Input supply current when in regulation | ISUPPLY | 26 | µA | VIN = 24 V, VOUT = 3.3 V, IOUT = 0 A, RFBT = 1 MΩ, PFM variant | 8 | ||
| Maximum switch duty cycle | DMAX | 98 | % | 8 | |||
| FB pin voltage required to trip short-circuit hiccup mode | VHC | 0.4 | V | 8 | |||
| Time between current-limit hiccup burst | tHC | 94 | ms | 8 | |||
| Switch voltage dead time | tD | 2 | ns | 8 | |||
| Thermal shutdown temperature | TSD | 170 | °C | Shutdown temperature | 8 | ||
| Thermal shutdown temperature recovery | TSD | 158 | °C | Recovery temperature | 8 |
Materials and finish
As the datasheet states them (page.json metadata.appearance; the 3D model's colours follow it).
| Part | Material | Colour / plating | Datasheet says | Page |
|---|---|---|---|---|
| contacts | copper | 8. Keep switch area small. Keep the copper area connecting the SW pin to the inductor as short and wide as | 36 |
CAD (Adom-generated)
- Symbol:
LMR36006BRNXR - Footprint:
Adom_Gen:Texas_Instruments_LMR36006_a1b7f3 - 3D model: generated to fit the land (STEP)
- 3D model files:
lmr36006brnxr-etched.step/lmr36006brnxr-etched.glbcarry the MPN laser-etched on the die in a toggleableAdom.LaserEtchgroup (Fusion-ready);lmr36006brnxr.step/lmr36006brnxr.glbare the bare package body.
Provenance
Data extracted from the manufacturer datasheet, not a distributor listing:
- Datasheet: Texas Instruments datasheet (52 pp, sha256
ea379c3bee95861f, retrieved 2026-11-20) - Extractor: parts-factory
2.0.0/extract_pins 0.3, primaryclaude-haiku-5-5(text), consensusclaude-sonnet-5-5(agreed), guards: pin_guards 0.1: passed. Pins are checked against the footprint pad set and their cited datasheet pages before publish. - CAD: symbol generated from the datasheet pin table; footprint an Adom_Gen land derived from the manufacturer drawing; 3D model generated to fit that land.