3D Model
Open in new tab ↗
Loads when you scroll to it. Unloads after 5 minutes in the background.
Symbol & Footprint
Schematic Symbol
Open full view ↗Loads when you scroll to it. Unloads after 5 minutes in the background.
PCB Footprint
Open full view ↗Loads when you scroll to it. Unloads after 5 minutes in the background.
Datasheet
Open in new tab ↗Loads when you scroll to it. Unloads after 5 minutes in the background.
Contents
README
markdownLMR16006YQ3DDCTQ1
Texas Instruments · DC-DC Converters · TSOT-23-6
LMR16006YQ3DDCTQ1 from Texas Instruments, in a TSOT-23-6. Pinout and pin descriptions extracted from the manufacturer datasheet (extract_pins, cross-checked by a second model); symbol, footprint, and 3D from KiCad-official CAD.
Pinout
| Pin | Name | Type | Function |
|---|---|---|---|
| 1 | CB | input | Switch FET gate bias voltage; the Cboot capacitor connects between CB and SW. |
| 2 | GND | power_in | Ground connection for the device. |
| 3 | FB | input | Feedback input that sets the output voltage through the divider ratio VOUT = VFB (1 + R1/R2). |
| 4 | SHDN | input | High-voltage-tolerant enable input with an internal pull-up current source; pull below 1.25 V to disable, float to enable, and use a two-resistor divider to set input undervoltage lockout. |
| 5 | VIN | power_in | Power input voltage pin that supplies the internal circuitry and is the drain node input for the internal high-side MOSFET. |
| 6 | SW | output | Switch node that connects to the inductor, the catch diode, and the Cboot capacitor. |
Key specifications
| Parameter | Value |
|---|---|
| Manufacturer | Texas Instruments |
| Package | TSOT-23-6 |
| Category | Power Management (PMIC) |
| Pins | 6 |
Electrical characteristics
Limits as printed in the datasheet (page.json metadata.characteristics carries them as data).
| Parameter | Symbol | Min | Typ | Max | Unit | Conditions | Page |
|---|---|---|---|---|---|---|---|
| VIN operating input voltage | VIN | 4 | 40 | V | 5 | ||
| Rising SHDN threshold voltage | VSHDN_Thre | 1.05 | 1.25 | 1.38 | V | 5 | |
| Feedback voltage | VFB | 0.747 | 0.765 | 0.782 | V | 5 | |
| Output voltage, fixed 3.3 V output version | VOUT | 3.201 | 3.3 | 3.399 | V | Fixed 3.3 V output version | 5 |
| Switching frequency | fSW | 1785 | 2100 | 2415 | kHz | 5 | |
| Peak current limit | ILIMIT | 1200 | 1700 | mA | VIN = 12 V, TJ = 25°C | 5 | |
| Shutdown input current | ISHDN | 1 | 3 | µA | VEN = 0 V | 5 | |
| Input current at SHDN | ISHDN | -4.2 | µA | SHDN = 2.3 V | 5 | ||
| Input current at SHDN | ISHDN | -1 | µA | SHDN = 0.9 V | 5 | ||
| Hysteresis current | ISHDN_HYS | -3 | µA | 5 | |||
| Operating quiescent current (non-switching) | IQ | 28 | µA | no load, VIN = 12 V | 5 | ||
| On-resistance | RDS_ON | 900 | mΩ | VIN = 12 V, CB to SW = 5.8 V | 5 | ||
| Undervoltage lockout rising threshold | UVLO | 4 | V | Rising threshold | 5 | ||
| Undervoltage lockout falling threshold | UVLO | 3 | V | Falling threshold | 5 | ||
| Thermal shutdown threshold | TSHDN | 170 | ºC | Ensured by design | 5 | ||
| Thermal shutdown hysteresis | THYS | 10 | ºC | Ensured by design | 5 | ||
| Minimum turn-on time | TON_MIN | 80 | ns | fSW = 2.1 MHz; ensured by design | 5 | ||
| Maximum duty cycle | DMAX | 97 | % | 5 | |||
| VIN to GND | -0.3 | 65 | V | 4 | |||
| SHDN to GND | -0.3 | 65 | V | 4 | |||
| FB to GND | -0.3 | 7 | V | 4 | |||
| CB to SW | -0.3 | 7 | V | 4 | |||
| SW to GND | -1 | 60 | V | 4 | |||
| SW to GND transients | -2 | 60 | V | less than 30 ns transients | 4 | ||
| Operation junction temperature | TJ | -40 | 150 | °C | Operation | 4 | |
| Storage temperature | Tstg | -55 | 165 | °C | 4 | ||
| VIN input voltage | VIN | 4 | 40 | V | 4 | ||
| CB voltage | CB | 4 | 46 | V | 4 | ||
| CB to SW voltage | -0.3 | 6 | V | 4 | |||
| SW voltage | SW | -1 | 40 | V | 4 | ||
| FB voltage | FB | 0 | 5.5 | V | 4 | ||
| SHDN voltage | SHDN | 0 | 40 | V | 4 | ||
| Operating junction temperature range | TJ | -40 | 125 | °C | 4 | ||
| Junction-to-ambient thermal resistance | RθJA | 102 | °C/W | DDC (SOT) 6-pin, JEDEC board, still air | 4 | ||
| Junction-to-case (top) thermal resistance | RθJCtop | 36.9 | °C/W | DDC (SOT) 6-pin, JEDEC board, still air | 4 | ||
| Junction-to-board characterization parameter | RθJB | 28.4 | °C/W | DDC (SOT) 6-pin, JEDEC board, still air | 4 |
Materials and finish
As the datasheet states them (page.json metadata.appearance; the 3D model's colours follow it).
| Part | Material | Colour / plating | Datasheet says | Page |
|---|---|---|---|---|
| contacts | copper | to minimize coupling noise into the feedback pin. 2. The input bypass capacitor Cin must be placed close to the VIN pin. This will reduce copper trace resistance | 15 |
CAD (KiCad official)
- Symbol:
LMR16006YQ3DDCTQ1 - Footprint:
Package_TO_SOT_SMD:TSOT-23-6 - 3D model: TSOT-23-6 (KiCad packages3D, STEP)
- 3D model files:
lmr16006yq3ddctq1-etched.step/lmr16006yq3ddctq1-etched.glbcarry the MPN laser-etched on the die in a toggleableAdom.LaserEtchgroup (Fusion-ready);lmr16006yq3ddctq1.step/lmr16006yq3ddctq1.glbare the bare package body.
Provenance
Data extracted from the manufacturer datasheet, not a distributor listing:
- Datasheet: Texas Instruments datasheet (24 pp, sha256
ba6e4a9332e01ff2, retrieved 2026-11-10, tier: manufacturer) - Extractor: parts-factory
2.0.0/extract_pins 0.3, primaryclaude-haiku-5-5(text), consensusclaude-sonnet-5-5(agreed), guards: pin_guards 0.1: passed. Pins are checked against the footprint pad set and their cited datasheet pages before publish. - CAD: KiCad official libraries (CC-BY-SA 4.0).