3D Model
Open in new tab ↗
Loads when you scroll to it. Unloads after 5 minutes in the background.
Symbol & Footprint
Schematic Symbol
Open full view ↗Loads when you scroll to it. Unloads after 5 minutes in the background.
PCB Footprint
Open full view ↗Loads when you scroll to it. Unloads after 5 minutes in the background.
Datasheet
Open in new tab ↗Loads when you scroll to it. Unloads after 5 minutes in the background.
README
markdownLMR14050SSQDDARQ1
Texas Instruments · DC-DC Converters · ESOP-8
LMR14050SSQDDARQ1 from Texas Instruments, in a ESOP-8. Pinout and pin descriptions extracted from the manufacturer datasheet (extract_pins, cross-checked by a second model); symbol, footprint, and 3D from KiCad-official CAD.
Pinout
| Pin | Name | Type | Function |
|---|---|---|---|
| 1 | BOOT | passive | Bootstrap capacitor connection for the high-side MOSFET driver; connect a high quality 0.1 µF capacitor from BOOT to SW. |
| 2 | VIN | power_in | Connect to power supply and bypass capacitors CIN; the path from VIN to the high frequency bypass CIN and GND must be as short as possible (4V to 40V operating). |
| 3 | EN | input | Enable pin with internal pull-up current source; pull below 1.2 V to disable, float or connect to VIN to enable, and use two resistors to adjust the input undervoltage lockout. |
| 4 | RT/SYNC | input | Resistor timing or external clock input; a resistor to ground sets the switching frequency, and pulling the pin above the PLL upper threshold makes it a high impedance synchronization clock input. |
| 5 | FB | input | Feedback input connected to the feedback divider to set VOUT; do not short this pin to ground during operation. |
| 6 | SS | passive | Soft-start control pin; connect a capacitor to set the soft-start time. |
| 7 | GND | power_in | System ground pin. |
| 8 | SW | power_out | Switching output of the regulator, internally connected to the high-side power MOSFET; connect to the power inductor. |
| 9 | Thermal Pad | power_in | Major heat dissipation path of the die; must be connected to the ground plane on the PCB. |
Key specifications
| Parameter | Value |
|---|---|
| Manufacturer | Texas Instruments |
| Package | ESOP-8 |
| Category | Power Supply Chip |
| Pins | 9 |
Electrical characteristics
Limits as printed in the datasheet (page.json metadata.characteristics carries them as data).
| Parameter | Symbol | Min | Typ | Max | Unit | Conditions | Page |
|---|---|---|---|---|---|---|---|
| Input voltage VIN, EN to GND | VIN | -0.3 | 44 | V | 4 | ||
| BOOT to GND | BOOT | -0.3 | 49 | V | 4 | ||
| SS to GND | SS | -0.3 | 5 | V | 4 | ||
| FB to GND (DDA package) | FB | -0.3 | 5.5 | V | 4 | ||
| RT/SYNC to GND | RT/SYNC | -0.3 | 3.6 | V | 4 | ||
| BOOT to SW (DDA package) | BOOT-SW | 5.5 | V | 4 | |||
| SW to GND | SW | -3 | 44 | V | 4 | ||
| Junction temperature | TJ | -40 | 150 | °C | 4 | ||
| Storage temperature | Tstg | -65 | 150 | °C | 4 | ||
| ESD HBM | V(ESD) | -2000 | 2000 | V | HBM, per AEC Q100-002 | 4 | |
| ESD CDM | V(ESD) | -750 | 750 | V | CDM, per AEC Q100-011 | 4 | |
| Input voltage | VIN | 4 | 40 | V | 4 | ||
| Output voltage | VOUT | 0.8 | 28 | V | 4 | ||
| BOOT voltage | BOOT | 45 | V | 4 | |||
| SW voltage | SW | -1 | 40 | V | 4 | ||
| FB voltage | FB | 0 | 5 | V | 4 | ||
| EN voltage | EN | 0 | 40 | V | 4 | ||
| RT/SYNC voltage | RT/SYNC | 0 | 3.3 | V | 4 | ||
| SS voltage | SS | 0 | 3 | V | 4 | ||
| PGOOD to GND | PGOOD | 0 | 5 | V | 4 | ||
| Switching frequency range at RT mode | fSW | 200 | 2500 | kHz | 4 | ||
| Switching frequency range at SYNC mode | fSW | 250 | 2300 | kHz | 4 | ||
| Operating junction temperature | TJ | -40 | 125 | °C | 4 | ||
| Operation input voltage | VIN | 4 | 40 | V | 5 | ||
| UVLO rising threshold | UVLO | 3.5 | 3.7 | 3.9 | V | Rising threshold | 5 |
| UVLO hysteresis | UVLO | 285 | mV | Hysteresis | 5 | ||
| Shutdown supply current | ISHDN | 1 | 3 | μA | VEN = 0 V, TJ = 25°C, 4.0 V ≤ VIN ≤ 40 V | 5 | |
| Operating quiescent current (non-switching) | IQ | 40 | μA | VFB = 1.0 V, TJ = 25°C | 5 | ||
| EN threshold voltage | VEN_TH | 1.05 | 1.2 | 1.38 | V | 5 | |
| EN pin current | IEN_PIN | -4.6 | μA | Enable threshold +50 mV | 5 | ||
| EN pin current | IEN_PIN | -1 | μA | Enable threshold -50 mV | 5 | ||
| EN hysteresis current | IEN_HYS | -3.6 | μA | 5 | |||
| SS pin current | ISS | -3 | μA | TJ = 25°C | 5 | ||
| PGOOD leakage current at high level output | IPG | 10 | 200 | nA | VPull-Up = 5 V | 5 | |
| PGOOD low level output voltage | VPG_LOW | 0.1 | V | IPull-Up = 1 mA | 5 | ||
| Minimum VIN for valid PGOOD output | VIN_PG_MIN | 1.6 | 1.95 | V | VPull-Up < 5 V at IPull-Up = 100 μA | 5 | |
| Feedback voltage | VFB | 0.744 | 0.75 | 0.756 | V | TJ = 25°C | 5 |
| Feedback voltage | VFB | 0.735 | 0.75 | 0.765 | V | TJ = -40 °C to 125 °C | 5 |
| High-side MOSFET on-resistance | RDS_ON | 90 | 180 | mΩ | VIN = 12 V | 6 | |
| High-side MOSFET current limit | ILIMT | 5.8 | 7.9 | 10.9 | A | VIN = 12 V, TJ = -40°C to 125°C, Open Loop | 6 |
| Thermal shutdown threshold | TSHDN | 170 | °C | 6 | |||
| Thermal shutdown hysteresis | THYS | 12 | °C | 6 | |||
| Switching frequency | fSW | 1758 | 1912 | 2066 | kHz | RT = 11.5 kΩ | 6 |
| Switching frequency range at SYNC mode | fSW | 250 | 2300 | kHz | 6 | ||
| Switching frequency dithering | FDITHER | -6 | 6 | % | Spread spectrum option, frequency dithering over center frequency | 6 | |
| SYNC clock high level threshold | VSYNC_HI | 1.7 | V | 6 | |||
| SYNC clock low level threshold | VSYNC_LO | 0.5 | V | 6 | |||
| Minimum SYNC input pulse width | TSYNC_MIN | 30 | ns | Measured at 500 kHz, VSYNC_HI > 3 V, VSYNC_LO < 0.3 V | 6 | ||
| PLL lock in time | TLOCK_IN | 100 | µs | Measured at 500 kHz | 6 | ||
| Minimum controllable on time | TON_MIN | 75 | ns | VIN = 12 V, ILoad = 1 A | 6 | ||
| Maximum duty cycle | DMAX | 97 | % | fSW = 200 kHz | 6 | ||
| Junction-to-ambient thermal resistance | RθJA | 43.2 | °C/W | DDA (HSOIC) 8 pins | 5 | ||
| Junction-to-top characterization parameter | ψJT | 5.2 | °C/W | DDA (HSOIC) 8 pins | 5 | ||
| Junction-to-board characterization parameter | ψJB | 16.4 | °C/W | DDA (HSOIC) 8 pins | 5 | ||
| Junction-to-case (top) thermal resistance | RθJC(top) | 52.1 | °C/W | DDA (HSOIC) 8 pins | 5 | ||
| Junction-to-case (bottom) thermal resistance | RθJC(bot) | 7.8 | °C/W | DDA (HSOIC) 8 pins | 5 | ||
| Junction-to-board thermal resistance | RθJB | 16.4 | °C/W | DDA (HSOIC) 8 pins | 5 |
CAD (KiCad official)
- Symbol:
LMR14050SSQDDARQ1 - Footprint:
Package_SO:SOIC-8-1EP_3.9x4.9mm_P1.27mm_EP2.41x3.3mm - 3D model: ESOP-8 (KiCad packages3D, STEP)
- 3D model files:
lmr14050ssqddarq1-etched.step/lmr14050ssqddarq1-etched.glbcarry the MPN laser-etched on the die in a toggleableAdom.LaserEtchgroup (Fusion-ready);lmr14050ssqddarq1.step/lmr14050ssqddarq1.glbare the bare package body.
Provenance
Data extracted from the manufacturer datasheet, not a distributor listing:
- Datasheet: Texas Instruments datasheet (38 pp, sha256
cefdbbf1b3380e4f, retrieved 2026-10-31, tier: manufacturer) - Extractor: parts-factory
2.0.0/extract_pins 0.3, primaryclaude-sonnet-5-5(text), consensusclaude-sonnet-5-5(agreed), guards: pin_guards 0.1: passed. Pins are checked against the footprint pad set and their cited datasheet pages before publish. - CAD: KiCad official libraries (CC-BY-SA 4.0).