main
Ray
Publish 0.1.0
e4fd295
LMR14030SQDPRTQ1
TI(德州仪器) · IC · WSON-10-EP(4x4)
LMR14030SQDPRTQ1 from TI(德州仪器), in a WSON-10-EP(4x4). Pinout and pin descriptions extracted from the manufacturer datasheet (extract_pins, cross-checked by a second model); symbol, footprint, and 3D from KiCad-official CAD.
Pinout
| Pin | Name | Type | Function |
|---|---|---|---|
| 1 | BOOT | power_out | Bootstrap capacitor connection for the high-side MOSFET driver; connect a high-quality 0.1 μF capacitor from BOOT to SW, with BOOT to SW limited to 6.5 V maximum for the DPR package. |
| 2 | VIN | power_in | Input supply pin, rated 4 V to 40 V in recommended operation; keep the path from VIN through the high-frequency bypass capacitor CIN to GND as short as possible. |
| 3 | VIN | power_in | Second VIN pin, connected internally to the same input supply; connect to the power supply and bypass capacitor CIN. |
| 4 | EN | input | Enable input with an internal pull-up current source; pull below 1.2 V to disable, and float or connect to VIN to enable, with input undervoltage lockout adjustable by two resistors. |
| 5 | RT/SYNC | input | Switching-frequency resistor timing pin or external clock input; a resistor to ground sets the frequency (200 kHz to 2.5 MHz in RT mode), and a clock above the PLL upper threshold switches the pin to a synchronization input (250 kHz to 2.3 MHz in SYNC mode). |
| 6 | SS | input | Soft-start control pin; connect a capacitor to set the soft-start time, with the pin rated 0 V to 3 V. |
| 7 | FB | input | Feedback input connected to the feedback divider to set VOUT; do not short this pin to ground during operation, and it is rated 0 V to 5 V (absolute maximum 7 V for the DPR package). |
| 8 | PGOOD | output | Open-drain power-good flag output; use a 10 kΩ to 100 kΩ pull-up to a logic rail or DC voltage no higher than 7 V. |
| 9 | GND | power_in | System ground pin for the regulator. |
| 10 | SW | power_out | Switching output of the regulator, internally connected to the high-side power MOSFET; connect to the power inductor, with SW rated -1 V to 40 V in recommended operation. |
| 11 | Thermal Pad | power_in | Major heat-dissipation path of the die; it must be connected to the ground plane on the PCB. |
Key specifications
| Parameter | Value |
|---|---|
| Manufacturer | TI(德州仪器) |
| Package | WSON-10-EP(4x4) |
| Category | |
| Pins | 11 |
Electrical characteristics
Limits as printed in the datasheet (page.json metadata.characteristics carries them as data).
| Parameter | Symbol | Min | Typ | Max | Unit | Conditions | Page |
|---|---|---|---|---|---|---|---|
| VIN, EN to GND | -0.3 | 44 | V | 4 | |||
| BOOT to GND | -0.3 | 49 | V | 4 | |||
| SS to GND | -0.3 | 5 | V | 4 | |||
| FB to GND (DPR package) | -0.3 | 7 | V | 4 | |||
| RT/SYNC to GND | -0.3 | 3.6 | V | 4 | |||
| PGOOD to GND | -0.3 | 7 | V | 4 | |||
| BOOT to SW (DPR package) | 6.5 | V | 4 | ||||
| SW to GND | -3 | 44 | V | 4 | |||
| Junction temperature | TJ | -40 | 150 | °C | 4 | ||
| Storage temperature | Tstg | -65 | 150 | °C | 4 | ||
| VIN input voltage | VIN | 4 | 40 | V | 4 | ||
| VOUT output voltage | VOUT | 0.8 | 28 | V | 4 | ||
| BOOT | 45 | V | 4 | ||||
| SW | -1 | 40 | V | 4 | |||
| FB | 0 | 5 | V | 4 | |||
| EN | 0 | 40 | V | 4 | |||
| RT/SYNC | 0 | 3.3 | V | 4 | |||
| SS | 0 | 3 | V | 4 | |||
| PGOOD to GND | 0 | 5 | V | 4 | |||
| Switching frequency range at RT mode | 200 | 2500 | kHz | 4 | |||
| Switching frequency range at SYNC mode | 250 | 2300 | kHz | 4 | |||
| Operating junction temperature | TJ | -40 | 125 | °C | 4 | ||
| Maximum soft-start capacitor (WSON package) | CSS | 4.7 | nF | WSON package | 12 | ||
| VIN operation input voltage | VIN | 4 | 40 | V | 5 | ||
| UVLO rising threshold | UVLO | 3.5 | 3.7 | 3.9 | V | 5 | |
| Shutdown supply current | ISHDN | 1 | 3 | μA | VEN = 0 V, TJ = 25°C, 4.0 V ≤ VIN ≤ 40 V | 5 | |
| EN threshold voltage | VEN_TH | 1.05 | 1.2 | 1.38 | V | 5 | |
| Feedback voltage | VFB | 0.744 | 0.75 | 0.756 | V | TJ = 25°C | 5 |
| Feedback voltage | VFB | 0.735 | 0.75 | 0.765 | V | TJ = -40°C to 125 °C | 5 |
| PGOOD leakage current at high level output | IPG | 10 | 200 | nA | VPull-Up = 5 V | 5 | |
| Minimum VIN for valid PGOOD output | VIN_PG_MIN | 1.6 | 1.95 | V | VPull-Up < 5 V at IPull-Up = 100 μA | 5 | |
| On-resistance (high-side MOSFET) | RDS_ON | 90 | 180 | mΩ | VIN = 12 V | 6 | |
| High-side MOSFET current limit | ILIMT | 4.1 | 5.5 | 7.7 | A | VIN = 12 V, TJ = -40°C to 125°C, Open Loop | 6 |
| Switching frequency | fSW | 1758 | 1912 | 2066 | kHz | RT = 11.5kΩ | 6 |
| Switching frequency dithering (spread spectrum option) | FDITHER | -6 | 6 | % | Spread spectrum option, frequency dithering over center frequency | 6 | |
| Switching frequency range at SYNC mode | 250 | 2300 | kHz | 6 | |||
| Minimum SYNC input pulse width | TSYNC_MIN | 30 | ns | Measured at 500kHz, VSYNC_HI > 3V, VSYNC_LO < 0.3V | 6 | ||
| Minimum controllable on time | TON_MIN | 75 | ns | VIN = 12V, ILoad = 1A | 6 | ||
| Maximum duty cycle | DMAX | 97 | % | fSW = 200kHz | 6 | ||
| Thermal resistance junction-to-ambient (DPR, WSON) | RθJA | 36.5 | °C/W | 5 | |||
| Junction-to-top characterization parameter (DPR, WSON) | ψJT | 0.3 | °C/W | 5 | |||
| Junction-to-board characterization parameter (DPR, WSON) | ψJB | 13.8 | °C/W | 5 | |||
| Junction-to-case (top) thermal resistance (DPR, WSON) | RθJC(top) | 35.2 | °C/W | 5 | |||
| Junction-to-case (bottom) thermal resistance (DPR, WSON) | RθJC(bot) | 3.1 | °C/W | 5 | |||
| Junction-to-board thermal resistance (DPR, WSON) | RθJB | 13.6 | °C/W | 5 |
CAD (KiCad official)
- Symbol:
LMR14030SQDPRTQ1 - Footprint:
Package_SON:WSON-10-1EP_4x4mm_P0.8mm_EP2.6x3mm - 3D model: WSON-10-EP(4x4) (KiCad packages3D, STEP)
- 3D model files:
lmr14030sqdprtq1-etched.step/lmr14030sqdprtq1-etched.glbcarry the MPN laser-etched on the die in a toggleableAdom.LaserEtchgroup (Fusion-ready);lmr14030sqdprtq1.step/lmr14030sqdprtq1.glbare the bare package body.
Provenance
Data extracted from the manufacturer datasheet, not a distributor listing:
- Datasheet: TI(德州仪器) datasheet (37 pp, sha256
60fab340a8d414e2, retrieved 2026-10-30, tier: manufacturer) - Extractor: parts-factory
2.0.0/extract_pins 0.3, primaryclaude-haiku-5-5(text), consensusclaude-sonnet-5-5(agreed), guards: pin_guards 0.1: passed. Pins are checked against the footprint pad set and their cited datasheet pages before publish. - CAD: KiCad official libraries (CC-BY-SA 4.0).
# LMR14030SQDPRTQ1
**TI(德州仪器)** · IC · WSON-10-EP(4x4)
LMR14030SQDPRTQ1 from TI(德州仪器), in a WSON-10-EP(4x4). Pinout and pin descriptions extracted from the manufacturer datasheet (extract_pins, cross-checked by a second model); symbol, footprint, and 3D from KiCad-official CAD.
## Pinout
| Pin | Name | Type | Function |
|---|---|---|---|
| 1 | BOOT | power_out | Bootstrap capacitor connection for the high-side MOSFET driver; connect a high-quality 0.1 μF capacitor from BOOT to SW, with BOOT to SW limited to 6.5 V maximum for the DPR package. |
| 2 | VIN | power_in | Input supply pin, rated 4 V to 40 V in recommended operation; keep the path from VIN through the high-frequency bypass capacitor CIN to GND as short as possible. |
| 3 | VIN | power_in | Second VIN pin, connected internally to the same input supply; connect to the power supply and bypass capacitor CIN. |
| 4 | EN | input | Enable input with an internal pull-up current source; pull below 1.2 V to disable, and float or connect to VIN to enable, with input undervoltage lockout adjustable by two resistors. |
| 5 | RT/SYNC | input | Switching-frequency resistor timing pin or external clock input; a resistor to ground sets the frequency (200 kHz to 2.5 MHz in RT mode), and a clock above the PLL upper threshold switches the pin to a synchronization input (250 kHz to 2.3 MHz in SYNC mode). |
| 6 | SS | input | Soft-start control pin; connect a capacitor to set the soft-start time, with the pin rated 0 V to 3 V. |
| 7 | FB | input | Feedback input connected to the feedback divider to set VOUT; do not short this pin to ground during operation, and it is rated 0 V to 5 V (absolute maximum 7 V for the DPR package). |
| 8 | PGOOD | output | Open-drain power-good flag output; use a 10 kΩ to 100 kΩ pull-up to a logic rail or DC voltage no higher than 7 V. |
| 9 | GND | power_in | System ground pin for the regulator. |
| 10 | SW | power_out | Switching output of the regulator, internally connected to the high-side power MOSFET; connect to the power inductor, with SW rated -1 V to 40 V in recommended operation. |
| 11 | Thermal Pad | power_in | Major heat-dissipation path of the die; it must be connected to the ground plane on the PCB. |
## Key specifications
| Parameter | Value |
|---|---|
| Manufacturer | TI(德州仪器) |
| Package | WSON-10-EP(4x4) |
| Category | |
| Pins | 11 |
## Electrical characteristics
Limits as printed in the datasheet (page.json `metadata.characteristics` carries them as data).
| Parameter | Symbol | Min | Typ | Max | Unit | Conditions | Page |
|---|---|---|---|---|---|---|---|
| VIN, EN to GND | | -0.3 | | 44 | V | | 4 |
| BOOT to GND | | -0.3 | | 49 | V | | 4 |
| SS to GND | | -0.3 | | 5 | V | | 4 |
| FB to GND (DPR package) | | -0.3 | | 7 | V | | 4 |
| RT/SYNC to GND | | -0.3 | | 3.6 | V | | 4 |
| PGOOD to GND | | -0.3 | | 7 | V | | 4 |
| BOOT to SW (DPR package) | | | | 6.5 | V | | 4 |
| SW to GND | | -3 | | 44 | V | | 4 |
| Junction temperature | TJ | -40 | | 150 | °C | | 4 |
| Storage temperature | Tstg | -65 | | 150 | °C | | 4 |
| VIN input voltage | VIN | 4 | | 40 | V | | 4 |
| VOUT output voltage | VOUT | 0.8 | | 28 | V | | 4 |
| BOOT | | | | 45 | V | | 4 |
| SW | | -1 | | 40 | V | | 4 |
| FB | | 0 | | 5 | V | | 4 |
| EN | | 0 | | 40 | V | | 4 |
| RT/SYNC | | 0 | | 3.3 | V | | 4 |
| SS | | 0 | | 3 | V | | 4 |
| PGOOD to GND | | 0 | | 5 | V | | 4 |
| Switching frequency range at RT mode | | 200 | | 2500 | kHz | | 4 |
| Switching frequency range at SYNC mode | | 250 | | 2300 | kHz | | 4 |
| Operating junction temperature | TJ | -40 | | 125 | °C | | 4 |
| Maximum soft-start capacitor (WSON package) | CSS | | | 4.7 | nF | WSON package | 12 |
| VIN operation input voltage | VIN | 4 | | 40 | V | | 5 |
| UVLO rising threshold | UVLO | 3.5 | 3.7 | 3.9 | V | | 5 |
| Shutdown supply current | ISHDN | | 1 | 3 | μA | VEN = 0 V, TJ = 25°C, 4.0 V ≤ VIN ≤ 40 V | 5 |
| EN threshold voltage | VEN_TH | 1.05 | 1.2 | 1.38 | V | | 5 |
| Feedback voltage | VFB | 0.744 | 0.75 | 0.756 | V | TJ = 25°C | 5 |
| Feedback voltage | VFB | 0.735 | 0.75 | 0.765 | V | TJ = -40°C to 125 °C | 5 |
| PGOOD leakage current at high level output | IPG | | 10 | 200 | nA | VPull-Up = 5 V | 5 |
| Minimum VIN for valid PGOOD output | VIN_PG_MIN | | 1.6 | 1.95 | V | VPull-Up < 5 V at IPull-Up = 100 μA | 5 |
| On-resistance (high-side MOSFET) | RDS_ON | | 90 | 180 | mΩ | VIN = 12 V | 6 |
| High-side MOSFET current limit | ILIMT | 4.1 | 5.5 | 7.7 | A | VIN = 12 V, TJ = -40°C to 125°C, Open Loop | 6 |
| Switching frequency | fSW | 1758 | 1912 | 2066 | kHz | RT = 11.5kΩ | 6 |
| Switching frequency dithering (spread spectrum option) | FDITHER | -6 | | 6 | % | Spread spectrum option, frequency dithering over center frequency | 6 |
| Switching frequency range at SYNC mode | | 250 | | 2300 | kHz | | 6 |
| Minimum SYNC input pulse width | TSYNC_MIN | 30 | | | ns | Measured at 500kHz, VSYNC_HI > 3V, VSYNC_LO < 0.3V | 6 |
| Minimum controllable on time | TON_MIN | 75 | | | ns | VIN = 12V, ILoad = 1A | 6 |
| Maximum duty cycle | DMAX | | | 97 | % | fSW = 200kHz | 6 |
| Thermal resistance junction-to-ambient (DPR, WSON) | RθJA | | 36.5 | | °C/W | | 5 |
| Junction-to-top characterization parameter (DPR, WSON) | ψJT | | 0.3 | | °C/W | | 5 |
| Junction-to-board characterization parameter (DPR, WSON) | ψJB | | 13.8 | | °C/W | | 5 |
| Junction-to-case (top) thermal resistance (DPR, WSON) | RθJC(top) | | 35.2 | | °C/W | | 5 |
| Junction-to-case (bottom) thermal resistance (DPR, WSON) | RθJC(bot) | | 3.1 | | °C/W | | 5 |
| Junction-to-board thermal resistance (DPR, WSON) | RθJB | | 13.6 | | °C/W | | 5 |
## CAD (KiCad official)
- Symbol: `LMR14030SQDPRTQ1`
- Footprint: `Package_SON:WSON-10-1EP_4x4mm_P0.8mm_EP2.6x3mm`
- 3D model: WSON-10-EP(4x4) (KiCad packages3D, STEP)
- 3D model files: `lmr14030sqdprtq1-etched.step` / `lmr14030sqdprtq1-etched.glb` carry the MPN laser-etched on the die in a toggleable `Adom.LaserEtch` group (Fusion-ready); `lmr14030sqdprtq1.step` / `lmr14030sqdprtq1.glb` are the bare package body.
## Provenance
Data extracted from the manufacturer datasheet, not a distributor listing:
- **Datasheet:** [TI(德州仪器) datasheet](https://www.ti.com/lit/ds/symlink/lmr14030-q1.pdf) (37 pp, sha256 `60fab340a8d414e2`, retrieved 2026-10-30, tier: manufacturer)
- **Extractor:** parts-factory `2.0.0` / `extract_pins 0.3`, primary `claude-haiku-5-5` (text), consensus `claude-sonnet-5-5` (agreed), guards: pin_guards 0.1: passed. Pins are checked against the footprint pad set and their cited datasheet pages before publish.
- **CAD:** KiCad official libraries (CC-BY-SA 4.0).
[Datasheet PDF](docs/lmr14030sqdprtq1-datasheet.pdf)