Loads when you scroll to it. Unloads after 5 minutes in the background.

Symbol & Footprint

Schematic Symbol

Open full view ↗
Loads when you scroll to it. Unloads after 5 minutes in the background.

PCB Footprint

Open full view ↗
Loads when you scroll to it. Unloads after 5 minutes in the background.
Loads when you scroll to it. Unloads after 5 minutes in the background.
Download PDF
Contents

README

markdown

LMR14030SQDPRTQ1

TI(德州仪器) · IC · WSON-10-EP(4x4)

LMR14030SQDPRTQ1 from TI(德州仪器), in a WSON-10-EP(4x4). Pinout and pin descriptions extracted from the manufacturer datasheet (extract_pins, cross-checked by a second model); symbol, footprint, and 3D from KiCad-official CAD.

Pinout

Pin Name Type Function
1 BOOT power_out Bootstrap capacitor connection for the high-side MOSFET driver; connect a high-quality 0.1 μF capacitor from BOOT to SW, with BOOT to SW limited to 6.5 V maximum for the DPR package.
2 VIN power_in Input supply pin, rated 4 V to 40 V in recommended operation; keep the path from VIN through the high-frequency bypass capacitor CIN to GND as short as possible.
3 VIN power_in Second VIN pin, connected internally to the same input supply; connect to the power supply and bypass capacitor CIN.
4 EN input Enable input with an internal pull-up current source; pull below 1.2 V to disable, and float or connect to VIN to enable, with input undervoltage lockout adjustable by two resistors.
5 RT/SYNC input Switching-frequency resistor timing pin or external clock input; a resistor to ground sets the frequency (200 kHz to 2.5 MHz in RT mode), and a clock above the PLL upper threshold switches the pin to a synchronization input (250 kHz to 2.3 MHz in SYNC mode).
6 SS input Soft-start control pin; connect a capacitor to set the soft-start time, with the pin rated 0 V to 3 V.
7 FB input Feedback input connected to the feedback divider to set VOUT; do not short this pin to ground during operation, and it is rated 0 V to 5 V (absolute maximum 7 V for the DPR package).
8 PGOOD output Open-drain power-good flag output; use a 10 kΩ to 100 kΩ pull-up to a logic rail or DC voltage no higher than 7 V.
9 GND power_in System ground pin for the regulator.
10 SW power_out Switching output of the regulator, internally connected to the high-side power MOSFET; connect to the power inductor, with SW rated -1 V to 40 V in recommended operation.
11 Thermal Pad power_in Major heat-dissipation path of the die; it must be connected to the ground plane on the PCB.

Key specifications

Parameter Value
Manufacturer TI(德州仪器)
Package WSON-10-EP(4x4)
Category
Pins 11

Electrical characteristics

Limits as printed in the datasheet (page.json metadata.characteristics carries them as data).

Parameter Symbol Min Typ Max Unit Conditions Page
VIN, EN to GND -0.3 44 V 4
BOOT to GND -0.3 49 V 4
SS to GND -0.3 5 V 4
FB to GND (DPR package) -0.3 7 V 4
RT/SYNC to GND -0.3 3.6 V 4
PGOOD to GND -0.3 7 V 4
BOOT to SW (DPR package) 6.5 V 4
SW to GND -3 44 V 4
Junction temperature TJ -40 150 °C 4
Storage temperature Tstg -65 150 °C 4
VIN input voltage VIN 4 40 V 4
VOUT output voltage VOUT 0.8 28 V 4
BOOT 45 V 4
SW -1 40 V 4
FB 0 5 V 4
EN 0 40 V 4
RT/SYNC 0 3.3 V 4
SS 0 3 V 4
PGOOD to GND 0 5 V 4
Switching frequency range at RT mode 200 2500 kHz 4
Switching frequency range at SYNC mode 250 2300 kHz 4
Operating junction temperature TJ -40 125 °C 4
Maximum soft-start capacitor (WSON package) CSS 4.7 nF WSON package 12
VIN operation input voltage VIN 4 40 V 5
UVLO rising threshold UVLO 3.5 3.7 3.9 V 5
Shutdown supply current ISHDN 1 3 μA VEN = 0 V, TJ = 25°C, 4.0 V ≤ VIN ≤ 40 V 5
EN threshold voltage VEN_TH 1.05 1.2 1.38 V 5
Feedback voltage VFB 0.744 0.75 0.756 V TJ = 25°C 5
Feedback voltage VFB 0.735 0.75 0.765 V TJ = -40°C to 125 °C 5
PGOOD leakage current at high level output IPG 10 200 nA VPull-Up = 5 V 5
Minimum VIN for valid PGOOD output VIN_PG_MIN 1.6 1.95 V VPull-Up < 5 V at IPull-Up = 100 μA 5
On-resistance (high-side MOSFET) RDS_ON 90 180 mΩ VIN = 12 V 6
High-side MOSFET current limit ILIMT 4.1 5.5 7.7 A VIN = 12 V, TJ = -40°C to 125°C, Open Loop 6
Switching frequency fSW 1758 1912 2066 kHz RT = 11.5kΩ 6
Switching frequency dithering (spread spectrum option) FDITHER -6 6 % Spread spectrum option, frequency dithering over center frequency 6
Switching frequency range at SYNC mode 250 2300 kHz 6
Minimum SYNC input pulse width TSYNC_MIN 30 ns Measured at 500kHz, VSYNC_HI > 3V, VSYNC_LO < 0.3V 6
Minimum controllable on time TON_MIN 75 ns VIN = 12V, ILoad = 1A 6
Maximum duty cycle DMAX 97 % fSW = 200kHz 6
Thermal resistance junction-to-ambient (DPR, WSON) RθJA 36.5 °C/W 5
Junction-to-top characterization parameter (DPR, WSON) ψJT 0.3 °C/W 5
Junction-to-board characterization parameter (DPR, WSON) ψJB 13.8 °C/W 5
Junction-to-case (top) thermal resistance (DPR, WSON) RθJC(top) 35.2 °C/W 5
Junction-to-case (bottom) thermal resistance (DPR, WSON) RθJC(bot) 3.1 °C/W 5
Junction-to-board thermal resistance (DPR, WSON) RθJB 13.6 °C/W 5

CAD (KiCad official)

  • Symbol: LMR14030SQDPRTQ1
  • Footprint: Package_SON:WSON-10-1EP_4x4mm_P0.8mm_EP2.6x3mm
  • 3D model: WSON-10-EP(4x4) (KiCad packages3D, STEP)
  • 3D model files: lmr14030sqdprtq1-etched.step / lmr14030sqdprtq1-etched.glb carry the MPN laser-etched on the die in a toggleable Adom.LaserEtch group (Fusion-ready); lmr14030sqdprtq1.step / lmr14030sqdprtq1.glb are the bare package body.

Provenance

Data extracted from the manufacturer datasheet, not a distributor listing:

  • Datasheet: TI(德州仪器) datasheet (37 pp, sha256 60fab340a8d414e2, retrieved 2026-10-30, tier: manufacturer)
  • Extractor: parts-factory 2.0.0 / extract_pins 0.3, primary claude-haiku-5-5 (text), consensus claude-sonnet-5-5 (agreed), guards: pin_guards 0.1: passed. Pins are checked against the footprint pad set and their cited datasheet pages before publish.
  • CAD: KiCad official libraries (CC-BY-SA 4.0).

Datasheet PDF