3D Model
Open in new tab ↗
Loads when you scroll to it. Unloads after 5 minutes in the background.
Symbol & Footprint
Schematic Symbol
Open full view ↗Loads when you scroll to it. Unloads after 5 minutes in the background.
PCB Footprint
Open full view ↗Loads when you scroll to it. Unloads after 5 minutes in the background.
Datasheet
Open in new tab ↗Loads when you scroll to it. Unloads after 5 minutes in the background.
README
markdownLMK1D1208RHDR
Texas Instruments · Clock Buffers, Drivers · VQFN-28(5x5)
LMK1D1208RHDR from Texas Instruments, in a VQFN-28(5x5). Pinout and pin descriptions extracted from the manufacturer datasheet (extract_pins, cross-checked by a second model); symbol, footprint, and 3D from KiCad-official CAD.
Pinout
| Pin | Name | Type | Function |
|---|---|---|---|
| 1 | GND | power_in | Ground. |
| 2 | OUT7_P | output | Positive side of differential LVDS output pair number 7. |
| 3 | OUT7_N | output | Negative side of differential LVDS output pair number 7. |
| 4 | IN_SEL | input | Input select with internal 500 kΩ pull-up and 320 kΩ pull-down: 0 selects IN0, 1 selects IN1, open disables the inputs and holds outputs at static logic low. |
| 5 | IN1_P | input | Secondary clock input, positive side of a differential pair or single-ended input. |
| 6 | IN1_N | input | Secondary clock input, negative side of a differential pair or single-ended input. |
| 7 | VAC_REF1 | output | Bias voltage output for capacitively coupled inputs; TI recommends a 0.1 µF capacitor to GND if used. |
| 8 | VDD | power_in | Device supply of 1.8 V, 2.5 V or 3.3 V (1.71 V to 3.465 V). |
| 9 | IN0_P | input | Primary clock input, positive side of a differential pair or single-ended input. |
| 10 | IN0_N | input | Primary clock input, negative side of a differential pair or single-ended input. |
| 11 | VAC_REF0 | output | Bias voltage output for capacitively coupled inputs; TI recommends a 0.1 µF capacitor to GND if used. |
| 12 | OUT0_P | output | Positive side of differential LVDS output pair number 0. |
| 13 | OUT0_N | output | Negative side of differential LVDS output pair number 0. |
| 14 | GND | power_in | Ground. |
| 15 | VDD | power_in | Device supply of 1.8 V, 2.5 V or 3.3 V (1.71 V to 3.465 V). |
| 16 | OUT1_P | output | Positive side of differential LVDS output pair number 1. |
| 17 | OUT1_N | output | Negative side of differential LVDS output pair number 1. |
| 18 | OUT2_P | output | Positive side of differential LVDS output pair number 2. |
| 19 | OUT2_N | output | Negative side of differential LVDS output pair number 2. |
| 20 | OUT3_P | output | Positive side of differential LVDS output pair number 3. |
| 21 | OUT3_N | output | Negative side of differential LVDS output pair number 3. |
| 22 | OUT4_P | output | Positive side of differential LVDS output pair number 4. |
| 23 | OUT4_N | output | Negative side of differential LVDS output pair number 4. |
| 24 | OUT5_P | output | Positive side of differential LVDS output pair number 5. |
| 25 | OUT5_N | output | Negative side of differential LVDS output pair number 5. |
| 26 | OUT6_P | output | Positive side of differential LVDS output pair number 6. |
| 27 | OUT6_N | output | Negative side of differential LVDS output pair number 6. |
| 28 | VDD | power_in | Device supply of 1.8 V, 2.5 V or 3.3 V (1.71 V to 3.465 V). |
| 29 | DAP | power_in | Die attach pad (exposed thermal pad) connected to GND; solder to the PCB ground plane for thermal performance. |
Key specifications
| Parameter | Value |
|---|---|
| Manufacturer | Texas Instruments |
| Package | VQFN-28(5x5) |
| Category | RTC/Clock Chip |
| Pins | 29 |
Electrical characteristics
Limits as printed in the datasheet (page.json metadata.characteristics carries them as data).
| Parameter | Symbol | Min | Typ | Max | Unit | Conditions | Page |
|---|---|---|---|---|---|---|---|
| Supply voltage 3.3V | VDD | 3.135 | 3.3 | 3.465 | V | 3.3V supply | 8 |
| Supply voltage 2.5V | VDD | 2.375 | 2.5 | 2.625 | V | 2.5V supply | 8 |
| Supply voltage 1.8V | VDD | 1.71 | 1.8 | 1.89 | V | 1.8V supply | 8 |
| Supply ramp time | 0.1 | 20 | ms | Monotonic ramp (10-90% of VDD) | 8 | ||
| Operating ambient temperature | TA | -40 | 105 | °C | 8 | ||
| Operating junction temperature | TJ | -40 | 135 | °C | 8 | ||
| Supply voltage | VDD | -0.3 | 3.6 | V | 8 | ||
| Input voltage | VIN | -0.3 | 3.6 | V | 8 | ||
| Input current | IIN | -20 | 20 | mA | 8 | ||
| Continuous output current | IO | -50 | 50 | mA | 8 | ||
| Junction temperature | TJ | 135 | °C | 8 | |||
| Storage temperature | Tstg | -65 | 150 | °C | Device unpowered | 8 | |
| ESD HBM | V(ESD) | -3000 | 3000 | V | HBM, ANSI/ESDA/JEDEC JS-001, all pins | 8 | |
| ESD CDM | V(ESD) | -1000 | 1000 | V | CDM, JESD22-C101, all pins | 8 | |
| Junction-to-ambient thermal resistance | RθJA | 38.9 | °C/W | VQFN 28-pin (RHD) | 9 | ||
| Junction-to-case (top) thermal resistance | RθJC(top) | 32.1 | °C/W | VQFN 28-pin (RHD) | 9 | ||
| Junction-to-board thermal resistance | RθJB | 18.7 | °C/W | VQFN 28-pin (RHD) | 9 | ||
| Junction-to-top characterization parameter | ΨJT | 1 | °C/W | VQFN 28-pin (RHD) | 9 | ||
| Junction-to-board characterization parameter | ΨJB | 18.7 | °C/W | VQFN 28-pin (RHD) | 9 | ||
| Junction-to-case (bottom) thermal resistance | RθJC(bot) | 8.2 | °C/W | VQFN 28-pin (RHD) | 9 | ||
| Static supply current LMK1D1208 | IDDSTAT | 55 | mA | All outputs enabled and unterminated, f = 0Hz | 9 | ||
| Supply current at 100MHz LMK1D1208 | IDD100M | 78 | 95 | mA | All outputs enabled, RL = 100Ω, f = 100MHz | 9 | |
| Three-state input open | VdI3 | 0.4 | V | Open; 0.4 × VCC | 9 | ||
| Input low voltage | VIL | -0.3 | 0.3 | V | Max input voltage for logic 0 state; 0.3 × VCC max | 9 | |
| Input high current (control) | IIH | 30 | µA | VDD can be 1.8V/2.5V/3.3V, VIH = VDD | 9 | ||
| Input low current (control) | IIL | -30 | µA | VDD can be 1.8V/2.5V/3.3V, VIH = VDD | 9 | ||
| Input pullup resistor | Rpull-up(EN) | 500 | kΩ | 9 | |||
| Input pulldown resistor | Rpull-down(EN) | 320 | kΩ | 9 | |||
| Input frequency (LVCMOS) | fIN | 0 | 250 | MHz | Clock input, DC to 250 MHz | 9 | |
| Single-ended input voltage swing | VIN_S-E | 0.4 | 3.465 | V | Assumes square wave input with two levels | 9 | |
| Input slew rate | dVIN/dt | 0.05 | V/ns | 20% to 80% of amplitude | 9 | ||
| Input high current (LVCMOS) | IIH | 50 | µA | VDD = 3.465V, VIH = 3.465V | 9 | ||
| Input low current (LVCMOS) | IIL | -30 | µA | VDD = 3.465V, VIL = 0V | 9 | ||
| Input capacitance (LVCMOS) | CIN_SE | 3.5 | pF | At 25°C | 9 | ||
| Input frequency (differential) | fIN | 2 | GHz | Clock input | 9 | ||
| Differential input voltage peak-to-peak | VIN,DIFF(p-p) | 0.3 | 2.4 | VPP | VICM = 1V (VDD = 1.8V) | 9 | |
| Input common-mode voltage | VICM | 0.25 | 2.3 | V | VIN,DIFF(P-P) > 0.4V (VDD = 1.8V/2.5/3.3V) | 9 | |
| Input high current (differential) | IIH | 30 | µA | VDD = 3.465V, VINP = 2.4V, VINN = 1.2V | 10 | ||
| Input low current (differential) | IIL | -30 | µA | VDD = 3.465V, VINP = 0V, VINN = 1.2V | 10 | ||
| Input capacitance (single-ended) | CIN_S-E | 3.5 | pF | At 25°C | 10 | ||
| Differential output voltage magnitude | /VOD/ | 250 | 350 | 450 | mV | VIN,DIFF(P-P) = 0.3V, RLOAD = 100Ω | 10 |
| Differential output voltage magnitude | /VOD/ | 400 | 500 | 650 | mV | VIN,DIFF(P-P) = 0.3V, RLOAD = 100Ω, AMP_SEL = 1 | 10 |
| Change in VOD | ΔVOD | -15 | 15 | mV | VIN,DIFF(P-P) = 0.3V, RLOAD = 100Ω | 10 | |
| Change in VOD | ΔVOD | -20 | 20 | mV | VIN,DIFF(P-P) = 0.3V, RLOAD = 100Ω, AMP_SEL = 1 | 10 | |
| Steady-state common-mode output voltage | VOC(SS) | 1 | 1.2 | V | VIN,DIFF(P-P) = 0.3V, RLOAD = 100Ω (VDD = 1.8V) | 10 | |
| Steady-state common-mode output voltage | VOC(SS) | 1.1 | 1.375 | V | VIN,DIFF(P-P) = 0.3V, RLOAD = 100Ω (VDD = 2.5V/3.3V) | 10 | |
| Change in steady-state common-mode output voltage | ΔVOC(SS) | -15 | 15 | mV | VIN,DIFF(P-P) = 0.3V, RLOAD = 100Ω | 10 | |
| Output overshoot and undershoot | Vring | -0.1 | 0.1 | VOD | VIN,DIFF(P-P) = 0.3V, RLOAD = 100Ω, fOUT = 491.52MHz | 10 | |
| Output AC common mode | VOS | 50 | 100 | mVpp | VIN,DIFF(P-P) = 0.3V, RLOAD = 100Ω | 10 | |
| Short-circuit output current (differential) | IOS | -12 | 12 | mA | VOUTP = VOUTN | 10 | |
| Short-circuit output current (common mode) | IOS(cm) | -24 | 24 | mA | VOUTP = VOUTN = 0 | 10 | |
| Propagation delay | tPD | 0.3 | 0.575 | ns | VIN,DIFF(P-P) = 0.3V, RLOAD = 100Ω | 10 | |
| Part-to-part skew | tSK,PP | 250 | ps | Same input and output load, same operating conditions | 10 | ||
| Pulse skew | tSK,P | -20 | 20 | ps | 50% duty cycle input, crossing point to crossing point distortion | 10 | |
| Random additive jitter (rms) | tRJIT(ADD) | 50 | 60 | fs, RMS | fIN = 156.25MHz, 50% duty cycle, input slew rate = 1.5V/ns, integration range = 12kHz - 20MHz, RLOAD = 100Ω | 10 | |
| Multiplexer isolation | MUXISO | 80 | dB | fIN = 156.25MHz | 12 | ||
| Output duty cycle | ODC | 45 | 55 | % | Input duty cycle 50% | 12 | |
| Output rise and fall time | tR/tF | 300 | ps | 20% to 80%, RLOAD = 100Ω | 12 | ||
| Reference output voltage | VAC_REF | 0.9 | 1.25 | 1.375 | V | VDD = 2.5V, ILOAD = 100µA | 12 |
| Power supply noise rejection | PSNR | -70 | dBc | 10kHz, 100mVpp ripple on VDD, fcarrier = 156.25MHz, VDD = 2.5V/3.3V | 12 | ||
| Power supply noise rejection | PSNR | -50 | dBc | 1MHz, 100mVpp ripple on VDD, fcarrier = 156.25MHz, VDD = 2.5V/3.3V | 12 | ||
| Phase noise 1kHz offset | PN1kHz | -143 | dBc/Hz | 156.25MHz carrier, 50% duty cycle, input slew rate = 1.5V/ns, RLOAD = 100Ω | 11 | ||
| Phase noise 10kHz offset | PN10kHz | -152 | dBc/Hz | 156.25MHz carrier, 50% duty cycle, input slew rate = 1.5V/ns, RLOAD = 100Ω | 11 | ||
| Phase noise 100kHz offset | PN100kHz | -157 | dBc/Hz | 156.25MHz carrier, 50% duty cycle, input slew rate = 1.5V/ns, RLOAD = 100Ω | 11 | ||
| Phase noise 1MHz offset | PN1MHz | -160 | dBc/Hz | 156.25MHz carrier, 50% duty cycle, input slew rate = 1.5V/ns, RLOAD = 100Ω | 11 | ||
| Phase noise floor | PNfloor | -164 | dBc/Hz | 156.25MHz carrier, 50% duty cycle, input slew rate = 1.5V/ns, RLOAD = 100Ω | 11 |
CAD (KiCad official)
- Symbol:
LMK1D1208RHDR - Footprint:
Package_DFN_QFN:QFN-28-1EP_5x5mm_P0.5mm_EP3.35x3.35mm - 3D model: VQFN-28(5x5) (KiCad packages3D, STEP)
- 3D model files:
lmk1d1208rhdr-etched.step/lmk1d1208rhdr-etched.glbcarry the MPN laser-etched on the die in a toggleableAdom.LaserEtchgroup (Fusion-ready);lmk1d1208rhdr.step/lmk1d1208rhdr.glbare the bare package body.
Provenance
Data extracted from the manufacturer datasheet, not a distributor listing:
- Datasheet: Texas Instruments datasheet (38 pp, sha256
d94c1191598792aa, retrieved 2026-10-31, tier: manufacturer) - Datasheet language: Chinese. Pin names, descriptions, and specs on this page were extracted and translated to English by ds2sf; the linked PDF is the manufacturer original.
- Extractor: parts-factory
2.0.0/extract_pins 0.3, primaryclaude-sonnet-5-5(text), consensusclaude-sonnet-5-5(agreed), guards: pin_guards 0.1: passed. Pins are checked against the footprint pad set and their cited datasheet pages before publish. - CAD: KiCad official libraries (CC-BY-SA 4.0).