main
History Download
Ray Publish 0.1.0 c98180d

LMK05318BRGZT

Texas Instruments · Clock Generators / Frequency Synthesizers / PLL · VQFN-48-EP(7x7)

LMK05318BRGZT from Texas Instruments, in a VQFN-48-EP(7x7). Pinout and pin descriptions extracted from the manufacturer datasheet (extract_pins, cross-checked by a second model); symbol, footprint, and 3D from KiCad-official CAD.

Pinout

Pin Name Type Function
1 STATUS0 bidirectional Status output 0 with programmable status signal, driver type (3.3V LVCMOS or open-drain, which needs an external pullup), and polarity; leave floating if unused.
2 STATUS1/FDEC bidirectional Status output 1 with the same programmable options as STATUS0; in I2C mode it can act as the DCO frequency-decrement (FDEC) input.
3 CAP_DIG passive External LDO bypass capacitor for the digital core logic; place a 10µF capacitor as close to the pin as possible.
4 VDD_DIG power_in 3.3V core supply for the digital blocks; place a 1µF capacitor as close to the pin as possible.
5 VDD_IN power_in 3.3V core supply for the PRIREF and SECREF reference inputs; place a 10µF capacitor as close to the pin as possible.
6 PRIREF_P input Primary DPLL reference clock input (positive); accepts a differential or single-ended clock with a programmable input type and internal termination, and an unused pair can be left floating.
7 PRIREF_N input Primary DPLL reference clock input (negative); for single-ended LVCMOS, pull this pin down to ground and drive PRIREF_P.
8 REFSEL input Manual DPLL reference selection (3-level, 1.8V compatible): 0 selects PRIREF, 1 selects SECREF, and Float or VIM selects auto; leave floating if unused.
9 HW_SW_CTRL input 3-level, 1.8V compatible device start-up mode select that is sampled only at power-on reset to choose EEPROM+I2C (0), I2C+ROM (1), or EEPROM+SPI (Float/VIM).
10 SECREF_P input Secondary DPLL reference clock input (positive); accepts a differential or single-ended clock with a programmable input type and internal termination, and an unused pair can be left floating.
11 SECREF_N input Secondary DPLL reference clock input (negative); for single-ended LVCMOS, pull this pin down to ground and drive SECREF_P.
12 GPIO0/SYNCN input Multifunction logic pin; in EEPROM+I2C mode (HW_SW_CTRL = 0) it is the active-low output SYNC input, and it should be pulled up externally if not used.
13 PDN input Device power-down, active low: when pulled low the device is in hard reset with all blocks including the serial interface powered down, and when pulled high normal start-up begins.
14 OUT0_P output Clock output 0 (positive) from the OUT[0:3] bank, supporting AC-LVDS, AC-CML, AC-LVPECL, or HCSL; unused outputs must be terminated if active or disabled via registers.
15 OUT0_N output Clock output 0 (negative) from the OUT[0:3] bank, supporting AC-LVDS, AC-CML, AC-LVPECL, or HCSL; unused outputs must be terminated if active or disabled via registers.
16 OUT1_N output Clock output 1 (negative) from the OUT[0:3] bank, supporting AC-LVDS, AC-CML, AC-LVPECL, or HCSL; unused outputs must be terminated if active or disabled via registers.
17 OUT1_P output Clock output 1 (positive) from the OUT[0:3] bank, supporting AC-LVDS, AC-CML, AC-LVPECL, or HCSL; unused outputs must be terminated if active or disabled via registers.
18 VDDO_01 power_in Output supply (1.8V, 2.5V, or 3.3V) for the output clocks; place a 0.1µF capacitor as close to the pin as possible, and the pin can be left floating if the corresponding output is unused.
19 VDDO_23 power_in Output supply (1.8V, 2.5V, or 3.3V) for the output clocks; place a 0.1µF capacitor as close to the pin as possible, and the pin can be left floating if the corresponding output is unused.
20 OUT2_P output Clock output 2 (positive) from the OUT[0:3] bank, supporting AC-LVDS, AC-CML, AC-LVPECL, or HCSL; unused outputs must be terminated if active or disabled via registers.
21 OUT2_N output Clock output 2 (negative) from the OUT[0:3] bank, supporting AC-LVDS, AC-CML, AC-LVPECL, or HCSL; unused outputs must be terminated if active or disabled via registers.
22 OUT3_N output Clock output 3 (negative) from the OUT[0:3] bank, supporting AC-LVDS, AC-CML, AC-LVPECL, or HCSL; unused outputs must be terminated if active or disabled via registers.
23 OUT3_P output Clock output 3 (positive) from the OUT[0:3] bank, supporting AC-LVDS, AC-CML, AC-LVPECL, or HCSL; unused outputs must be terminated if active or disabled via registers.
24 GPIO1/SCS input Multifunction logic pin; in I2C mode it sets the I2C address LSBs (Low = 00b, Float = 01b, High = 10b), and in SPI mode it is the SPI chip select (SCS).
25 SDA/SDI bidirectional I2C serial data I/O (SDA, open-drain, needs external pullup) or SPI serial data input (SDI) depending on HW_SW_CTRL.
26 SCL/SCK input I2C serial clock input (SCL, open-drain, needs external pullup) or SPI serial clock input (SCK) depending on HW_SW_CTRL.
27 VDD_PLL1 power_in 3.3V core supply for PLL1, PLL2, and the digital blocks; place a 10µF capacitor as close to the pin as possible.
28 CAP_PLL1 passive External LDO bypass capacitor for APLL1; place a 10µF capacitor as close to the pin as possible.
29 LF1 passive External loop filter capacitor for APLL1; place a nearby capacitor on the pin, with a recommended value of 0.47µF (APLL LBW = 1.0kHz).
30 GPIO2/SDO/FINC bidirectional Multifunction logic pin; in I2C mode with pin control it is the DCO frequency-increment (FINC) input, and in SPI mode it is the SPI data output (SDO).
31 XO_P input XO/TCXO/OCXO reference input (positive) for the APLLs, accepting differential or single-ended clocks with a programmable input type; a single-ended LVCMOS clock up to 2.5V can be applied to this pin with XO_N pulled down.
32 XO_N input XO/TCXO/OCXO reference input (negative) for the APLLs; for single-ended LVCMOS, pull this pin down to ground and drive XO_P.
33 VDD_XO power_in 3.3V core supply for the XO input; place a 10µF capacitor as close to the pin as possible.
34 LF2 passive External loop filter capacitor for APLL2; place a nearby capacitor on the pin, with a recommended value of 0.1µF (APLL LBW = 500kHz).
35 CAP_PLL2 passive External LDO bypass capacitor for APLL2; place a capacitor as close to the pin as possible, with a recommended value of 10µF.
36 VDD_PLL2 power_in 3.3V core supply for PLL2 (with PLL1 and the digital blocks); place a 10µF capacitor as close to the pin as possible.
37 VDDO_4 power_in Output supply (1.8V, 2.5V, or 3.3V) for the output clocks; place a 0.1µF capacitor as close to the pin as possible, and the pin can be left floating if the corresponding output is unused.
38 OUT4_N output Clock output 4 (negative) from the OUT[4:7] bank, supporting AC-LVDS, AC-CML, AC-LVPECL, HCSL, or 1.8V LVCMOS; unused outputs must be terminated if active or disabled via registers.
39 OUT4_P output Clock output 4 (positive) from the OUT[4:7] bank, supporting AC-LVDS, AC-CML, AC-LVPECL, HCSL, or 1.8V LVCMOS; unused outputs must be terminated if active or disabled via registers.
40 VDDO_5 power_in Output supply (1.8V, 2.5V, or 3.3V) for the output clocks; place a 0.1µF capacitor as close to the pin as possible, and the pin can be left floating if the corresponding output is unused.
41 OUT5_N output Clock output 5 (negative) from the OUT[4:7] bank, supporting AC-LVDS, AC-CML, AC-LVPECL, HCSL, or 1.8V LVCMOS; unused outputs must be terminated if active or disabled via registers.
42 OUT5_P output Clock output 5 (positive) from the OUT[4:7] bank, supporting AC-LVDS, AC-CML, AC-LVPECL, HCSL, or 1.8V LVCMOS; unused outputs must be terminated if active or disabled via registers.
43 VDDO_6 power_in Output supply (1.8V, 2.5V, or 3.3V) for the output clocks; place a 0.1µF capacitor as close to the pin as possible, and the pin can be left floating if the corresponding output is unused.
44 OUT6_N output Clock output 6 (negative) from the OUT[4:7] bank, supporting AC-LVDS, AC-CML, AC-LVPECL, HCSL, or 1.8V LVCMOS; unused outputs must be terminated if active or disabled via registers.
45 OUT6_P output Clock output 6 (positive) from the OUT[4:7] bank, supporting AC-LVDS, AC-CML, AC-LVPECL, HCSL, or 1.8V LVCMOS; unused outputs must be terminated if active or disabled via registers.
46 VDDO_7 power_in Output supply (1.8V, 2.5V, or 3.3V) for the output clocks; place a 0.1µF capacitor as close to the pin as possible, and the pin can be left floating if the corresponding output is unused.
47 OUT7_N output Clock output 7 (negative) from the OUT[4:7] bank, supporting AC-LVDS, AC-CML, AC-LVPECL, HCSL, or 1.8V LVCMOS; unused outputs must be terminated if active or disabled via registers.
48 OUT7_P output Clock output 7 (positive) from the OUT[4:7] bank, supporting AC-LVDS, AC-CML, AC-LVPECL, HCSL, or 1.8V LVCMOS; unused outputs must be terminated if active or disabled via registers.
49 GND power_in Ground exposed thermal pad; connect to PCB ground layers with a 5x5 via pattern for proper electrical and thermal performance.

Key specifications

Parameter Value
Manufacturer Texas Instruments
Package VQFN-48-EP(7x7)
Category RTC/Clock Chip
Pins 49

Electrical characteristics

Limits as printed in the datasheet (page.json metadata.characteristics carries them as data).

Parameter Symbol Min Typ Max Unit Conditions Page
Core supply voltages VDD -0.3 3.6 V 8
Output supply voltages VDDO -0.3 3.6 V 8
Input voltage range for clock and logic inputs VIN -0.3 V 8
Output voltage range for logic outputs VOUT_LOGIC -0.3 V 8
Output voltage range for clock outputs VOUT -0.3 V 8
Junction temperature TJ 150 °C 8
Storage temperature range Tstg -65 150 °C 8
Core supply voltages VDD 3.135 3.3 3.465 V 8
Output supply voltage for AC-LVDS, AC-CML, AC-LVPECL, or HCSL driver VDDO_x 1.71 1.8 1.89 V AC-LVDS, AC-CML, AC-LVPECL, or HCSL driver, 1.8V option 8
Output supply voltage for AC-LVDS, AC-CML, AC-LVPECL, or HCSL driver VDDO_x 2.375 2.5 2.625 V AC-LVDS, AC-CML, AC-LVPECL, or HCSL driver, 2.5V option 8
Output supply voltage for AC-LVDS, AC-CML, AC-LVPECL, or HCSL driver VDDO_x 3.135 3.3 3.465 V AC-LVDS, AC-CML, AC-LVPECL, or HCSL driver, 3.3V option 8
Output supply voltage for 1.8V LVCMOS driver VDDO_x 1.71 1.8 1.89 V 1.8V LVCMOS driver 8
Input voltage range for clock and logic inputs VIN 0 3.465 V 8
Ambient or operating temperature TA -40 85 °C 8
Junction temperature TJ 125 °C 8
Power supply ramp time tVDD 0.01 100 ms 8
Total Current Consumption (all VDD and VDDO pins, 3.3V) IDDPDN 56 75 mA Device powered-down (PDN pin held low) 10
Input frequency range (XO) fIN 10 100 MHz 10
Single-ended input voltage swing (XO) VIN-SE 0.4 2.6 Vpp Single ended input, internal AC coupling 10
Differential input peak to peak voltage swing (XO) VIN-DIFF 0.4 2 Vpp Differential input 10
Differential input voltage swing (XO) VID 0.2 1 /V/ Differential input 10
Input slew rate (XO) dV/dt 0.2 0.5 V/ns 10
Input duty cycle IDC 40 60 % 10
Input leakage (XO) IIN -350 350 µA 50Ω and 100Ω internal terminations disabled 10
Input frequency range (PRIREF, SECREF) fIN 5 800 MHz Differential input 10
Single-ended input voltage swing (PRIREF, SECREF) VIN-SE 0.4 2.6 Vpp AC-coupled input 10
Differential input peak to peak voltage swing (PRIREF, SECREF) VIN-DIFF 0.4 2 Vpp Differential input, VHYST = 50mV 10
Differential input peak to peak voltage swing (PRIREF, SECREF) VIN-DIFF 0.7 2 Vpp Differential input, VHYST = 200mV 10
Differential input voltage swing (PRIREF, SECREF) VID 0.2 1 V Differential input, VHYST = 50mV 10
Differential input voltage swing (PRIREF, SECREF) VID 0.35 1 V Differential input, VHYST = 200mV 10
Input slew rate (PRIREF, SECREF) dV/dt 0.2 0.5 V/ns 10
Input leakage (PRIREF, SECREF) IIN -350 350 µA 50Ω and 100Ω internal terminations disabled 10
VCO2 Frequency Range fVCO2 5500 6250 MHz 10
AC-LVDS output voltage swing (VOH - VOL) VOD 250 390 450 mV 25MHz ≤ fOUT ≤ 800MHz; TYP at 156.25MHz 11
AC-LVDS output common mode VOS 100 430 mV 11
AC-CML output voltage swing (VOH - VOL) VOD 400 600 800 mV 25MHz ≤ fOUT ≤ 800MHz; TYP at fOUT = 156.25MHz 11
AC-CML output common mode VOS 150 550 mV 11
AC-LVPECL output voltage swing (VOH - VOL) VOD 450 780 1000 mV 25MHz ≤ fOUT ≤ 800MHz; TYP at fOUT = 156.25MHz 12
AC-LVPECL output common mode VOS 300 700 mV 12
HCSL output high voltage VOH 600 880 mV fOUT ≤ 400MHz 12
HCSL output low voltage VOL -150 150 mV 12
3-level logic input mid voltage VIM 0.7 0.9 V Input floating with internal bias and PDN pulled low 13
3-level logic input high current IIH -40 40 µA VIH = VDD 13
DPLL bandwidth range BW 0.01 4000 Hz Programmed bandwidth setting 15
Phase hit between two reference inputs tHITLESS -50 50 ps With 0ppm error; valid for a single switchover event between two clock inputs at the same frequency 15
Frequency transient during hitless switch fHITLESS -10 10 ppb Valid for a single switchover event between two clock inputs at the same frequency 15
RMS Phase Jitter (12kHz to 20MHz) RJ 50 80 fs RMS 625MHz AC-DIFF output from APLL1, fXO = 48MHz, fPD1 = fXO/2, fVCO1 = 2.5GHz 14
RMS Phase Jitter (12kHz to 20MHz) RJ 60 90 fs RMS 156.25MHz AC-LVPECL output from APLL1, fXO = 48MHz, fPD1 = fXO/2, fVCO1 = 2.5GHz 14
Junction-to-ambient thermal resistance (4-layer JEDEC) RθJA 23.3 °C/W 4-layer JEDEC standard PCB, 48 pins 9
Junction-to-case (top) thermal resistance (4-layer JEDEC) RθJC(top) 13.2 °C/W 4-layer JEDEC standard PCB, 48 pins 9
Junction-to-board thermal resistance (4-layer JEDEC) RθJB 7.4 °C/W 4-layer JEDEC standard PCB, 48 pins 9
Junction-to-case (bottom) thermal resistance (4-layer JEDEC) RθJC(bot) 1.4 °C/W 4-layer JEDEC standard PCB, 48 pins 9
Junction-to-top characterization parameter (4-layer JEDEC) ψJT 0.2 °C/W 4-layer JEDEC standard PCB, 48 pins 9
Junction-to-board characterization parameter (4-layer JEDEC) ψJB 7.3 °C/W 4-layer JEDEC standard PCB, 48 pins 9
Junction-to-ambient thermal resistance (10-layer custom PCB) RθJA 9.1 °C/W 10-layer custom PCB, 48 pins 9
Junction-to-board thermal resistance (10-layer custom PCB) RθJB 4.4 °C/W 10-layer custom PCB, 48 pins 9
Junction-to-board characterization parameter (10-layer custom PCB) ψJB 4.4 °C/W 10-layer custom PCB, 48 pins 9

CAD (KiCad official)

  • Symbol: LMK05318BRGZT
  • Footprint: Package_DFN_QFN:QFN-48-1EP_7x7mm_P0.5mm_EP5.15x5.15mm
  • 3D model: VQFN-48-EP(7x7) (KiCad packages3D, STEP)
  • 3D model files: lmk05318brgzt-etched.step / lmk05318brgzt-etched.glb carry the MPN laser-etched on the die in a toggleable Adom.LaserEtch group (Fusion-ready); lmk05318brgzt.step / lmk05318brgzt.glb are the bare package body.

Provenance

Data extracted from the manufacturer datasheet, not a distributor listing:

  • Datasheet: Texas Instruments datasheet (93 pp, sha256 5895e107ae544f96, retrieved 2026-10-30, tier: manufacturer)
  • Extractor: parts-factory 2.0.0 / extract_pins 0.3, primary claude-haiku-5-5 (text), consensus claude-sonnet-5-5 (agreed), guards: pin_guards 0.1: passed. Pins are checked against the footprint pad set and their cited datasheet pages before publish.
  • CAD: KiCad official libraries (CC-BY-SA 4.0).

Datasheet PDF