Generated by kicad-footprint-generator · KiCad file format 20260206
LMK05318BRGZT
Texas Instruments · Clock Generators / Frequency Synthesizers / PLL · VQFN-48-EP(7x7)
LMK05318BRGZT from Texas Instruments, in a VQFN-48-EP(7x7). Pinout and pin descriptions extracted from the manufacturer datasheet (extract_pins, cross-checked by a second model); symbol, footprint, and 3D from KiCad-official CAD.
Pinout
| Pin | Name | Type | Function |
|---|---|---|---|
| 1 | STATUS0 | bidirectional | Status output 0 with programmable status signal, driver type (3.3V LVCMOS or open-drain, which needs an external pullup), and polarity; leave floating if unused. |
| 2 | STATUS1/FDEC | bidirectional | Status output 1 with the same programmable options as STATUS0; in I2C mode it can act as the DCO frequency-decrement (FDEC) input. |
| 3 | CAP_DIG | passive | External LDO bypass capacitor for the digital core logic; place a 10µF capacitor as close to the pin as possible. |
| 4 | VDD_DIG | power_in | 3.3V core supply for the digital blocks; place a 1µF capacitor as close to the pin as possible. |
| 5 | VDD_IN | power_in | 3.3V core supply for the PRIREF and SECREF reference inputs; place a 10µF capacitor as close to the pin as possible. |
| 6 | PRIREF_P | input | Primary DPLL reference clock input (positive); accepts a differential or single-ended clock with a programmable input type and internal termination, and an unused pair can be left floating. |
| 7 | PRIREF_N | input | Primary DPLL reference clock input (negative); for single-ended LVCMOS, pull this pin down to ground and drive PRIREF_P. |
| 8 | REFSEL | input | Manual DPLL reference selection (3-level, 1.8V compatible): 0 selects PRIREF, 1 selects SECREF, and Float or VIM selects auto; leave floating if unused. |
| 9 | HW_SW_CTRL | input | 3-level, 1.8V compatible device start-up mode select that is sampled only at power-on reset to choose EEPROM+I2C (0), I2C+ROM (1), or EEPROM+SPI (Float/VIM). |
| 10 | SECREF_P | input | Secondary DPLL reference clock input (positive); accepts a differential or single-ended clock with a programmable input type and internal termination, and an unused pair can be left floating. |
| 11 | SECREF_N | input | Secondary DPLL reference clock input (negative); for single-ended LVCMOS, pull this pin down to ground and drive SECREF_P. |
| 12 | GPIO0/SYNCN | input | Multifunction logic pin; in EEPROM+I2C mode (HW_SW_CTRL = 0) it is the active-low output SYNC input, and it should be pulled up externally if not used. |
| 13 | PDN | input | Device power-down, active low: when pulled low the device is in hard reset with all blocks including the serial interface powered down, and when pulled high normal start-up begins. |
| 14 | OUT0_P | output | Clock output 0 (positive) from the OUT[0:3] bank, supporting AC-LVDS, AC-CML, AC-LVPECL, or HCSL; unused outputs must be terminated if active or disabled via registers. |
| 15 | OUT0_N | output | Clock output 0 (negative) from the OUT[0:3] bank, supporting AC-LVDS, AC-CML, AC-LVPECL, or HCSL; unused outputs must be terminated if active or disabled via registers. |
| 16 | OUT1_N | output | Clock output 1 (negative) from the OUT[0:3] bank, supporting AC-LVDS, AC-CML, AC-LVPECL, or HCSL; unused outputs must be terminated if active or disabled via registers. |
| 17 | OUT1_P | output | Clock output 1 (positive) from the OUT[0:3] bank, supporting AC-LVDS, AC-CML, AC-LVPECL, or HCSL; unused outputs must be terminated if active or disabled via registers. |
| 18 | VDDO_01 | power_in | Output supply (1.8V, 2.5V, or 3.3V) for the output clocks; place a 0.1µF capacitor as close to the pin as possible, and the pin can be left floating if the corresponding output is unused. |
| 19 | VDDO_23 | power_in | Output supply (1.8V, 2.5V, or 3.3V) for the output clocks; place a 0.1µF capacitor as close to the pin as possible, and the pin can be left floating if the corresponding output is unused. |
| 20 | OUT2_P | output | Clock output 2 (positive) from the OUT[0:3] bank, supporting AC-LVDS, AC-CML, AC-LVPECL, or HCSL; unused outputs must be terminated if active or disabled via registers. |
| 21 | OUT2_N | output | Clock output 2 (negative) from the OUT[0:3] bank, supporting AC-LVDS, AC-CML, AC-LVPECL, or HCSL; unused outputs must be terminated if active or disabled via registers. |
| 22 | OUT3_N | output | Clock output 3 (negative) from the OUT[0:3] bank, supporting AC-LVDS, AC-CML, AC-LVPECL, or HCSL; unused outputs must be terminated if active or disabled via registers. |
| 23 | OUT3_P | output | Clock output 3 (positive) from the OUT[0:3] bank, supporting AC-LVDS, AC-CML, AC-LVPECL, or HCSL; unused outputs must be terminated if active or disabled via registers. |
| 24 | GPIO1/SCS | input | Multifunction logic pin; in I2C mode it sets the I2C address LSBs (Low = 00b, Float = 01b, High = 10b), and in SPI mode it is the SPI chip select (SCS). |
| 25 | SDA/SDI | bidirectional | I2C serial data I/O (SDA, open-drain, needs external pullup) or SPI serial data input (SDI) depending on HW_SW_CTRL. |
| 26 | SCL/SCK | input | I2C serial clock input (SCL, open-drain, needs external pullup) or SPI serial clock input (SCK) depending on HW_SW_CTRL. |
| 27 | VDD_PLL1 | power_in | 3.3V core supply for PLL1, PLL2, and the digital blocks; place a 10µF capacitor as close to the pin as possible. |
| 28 | CAP_PLL1 | passive | External LDO bypass capacitor for APLL1; place a 10µF capacitor as close to the pin as possible. |
| 29 | LF1 | passive | External loop filter capacitor for APLL1; place a nearby capacitor on the pin, with a recommended value of 0.47µF (APLL LBW = 1.0kHz). |
| 30 | GPIO2/SDO/FINC | bidirectional | Multifunction logic pin; in I2C mode with pin control it is the DCO frequency-increment (FINC) input, and in SPI mode it is the SPI data output (SDO). |
| 31 | XO_P | input | XO/TCXO/OCXO reference input (positive) for the APLLs, accepting differential or single-ended clocks with a programmable input type; a single-ended LVCMOS clock up to 2.5V can be applied to this pin with XO_N pulled down. |
| 32 | XO_N | input | XO/TCXO/OCXO reference input (negative) for the APLLs; for single-ended LVCMOS, pull this pin down to ground and drive XO_P. |
| 33 | VDD_XO | power_in | 3.3V core supply for the XO input; place a 10µF capacitor as close to the pin as possible. |
| 34 | LF2 | passive | External loop filter capacitor for APLL2; place a nearby capacitor on the pin, with a recommended value of 0.1µF (APLL LBW = 500kHz). |
| 35 | CAP_PLL2 | passive | External LDO bypass capacitor for APLL2; place a capacitor as close to the pin as possible, with a recommended value of 10µF. |
| 36 | VDD_PLL2 | power_in | 3.3V core supply for PLL2 (with PLL1 and the digital blocks); place a 10µF capacitor as close to the pin as possible. |
| 37 | VDDO_4 | power_in | Output supply (1.8V, 2.5V, or 3.3V) for the output clocks; place a 0.1µF capacitor as close to the pin as possible, and the pin can be left floating if the corresponding output is unused. |
| 38 | OUT4_N | output | Clock output 4 (negative) from the OUT[4:7] bank, supporting AC-LVDS, AC-CML, AC-LVPECL, HCSL, or 1.8V LVCMOS; unused outputs must be terminated if active or disabled via registers. |
| 39 | OUT4_P | output | Clock output 4 (positive) from the OUT[4:7] bank, supporting AC-LVDS, AC-CML, AC-LVPECL, HCSL, or 1.8V LVCMOS; unused outputs must be terminated if active or disabled via registers. |
| 40 | VDDO_5 | power_in | Output supply (1.8V, 2.5V, or 3.3V) for the output clocks; place a 0.1µF capacitor as close to the pin as possible, and the pin can be left floating if the corresponding output is unused. |
| 41 | OUT5_N | output | Clock output 5 (negative) from the OUT[4:7] bank, supporting AC-LVDS, AC-CML, AC-LVPECL, HCSL, or 1.8V LVCMOS; unused outputs must be terminated if active or disabled via registers. |
| 42 | OUT5_P | output | Clock output 5 (positive) from the OUT[4:7] bank, supporting AC-LVDS, AC-CML, AC-LVPECL, HCSL, or 1.8V LVCMOS; unused outputs must be terminated if active or disabled via registers. |
| 43 | VDDO_6 | power_in | Output supply (1.8V, 2.5V, or 3.3V) for the output clocks; place a 0.1µF capacitor as close to the pin as possible, and the pin can be left floating if the corresponding output is unused. |
| 44 | OUT6_N | output | Clock output 6 (negative) from the OUT[4:7] bank, supporting AC-LVDS, AC-CML, AC-LVPECL, HCSL, or 1.8V LVCMOS; unused outputs must be terminated if active or disabled via registers. |
| 45 | OUT6_P | output | Clock output 6 (positive) from the OUT[4:7] bank, supporting AC-LVDS, AC-CML, AC-LVPECL, HCSL, or 1.8V LVCMOS; unused outputs must be terminated if active or disabled via registers. |
| 46 | VDDO_7 | power_in | Output supply (1.8V, 2.5V, or 3.3V) for the output clocks; place a 0.1µF capacitor as close to the pin as possible, and the pin can be left floating if the corresponding output is unused. |
| 47 | OUT7_N | output | Clock output 7 (negative) from the OUT[4:7] bank, supporting AC-LVDS, AC-CML, AC-LVPECL, HCSL, or 1.8V LVCMOS; unused outputs must be terminated if active or disabled via registers. |
| 48 | OUT7_P | output | Clock output 7 (positive) from the OUT[4:7] bank, supporting AC-LVDS, AC-CML, AC-LVPECL, HCSL, or 1.8V LVCMOS; unused outputs must be terminated if active or disabled via registers. |
| 49 | GND | power_in | Ground exposed thermal pad; connect to PCB ground layers with a 5x5 via pattern for proper electrical and thermal performance. |
Key specifications
| Parameter | Value |
|---|---|
| Manufacturer | Texas Instruments |
| Package | VQFN-48-EP(7x7) |
| Category | RTC/Clock Chip |
| Pins | 49 |
Electrical characteristics
Limits as printed in the datasheet (page.json metadata.characteristics carries them as data).
| Parameter | Symbol | Min | Typ | Max | Unit | Conditions | Page |
|---|---|---|---|---|---|---|---|
| Core supply voltages | VDD | -0.3 | 3.6 | V | 8 | ||
| Output supply voltages | VDDO | -0.3 | 3.6 | V | 8 | ||
| Input voltage range for clock and logic inputs | VIN | -0.3 | V | 8 | |||
| Output voltage range for logic outputs | VOUT_LOGIC | -0.3 | V | 8 | |||
| Output voltage range for clock outputs | VOUT | -0.3 | V | 8 | |||
| Junction temperature | TJ | 150 | °C | 8 | |||
| Storage temperature range | Tstg | -65 | 150 | °C | 8 | ||
| Core supply voltages | VDD | 3.135 | 3.3 | 3.465 | V | 8 | |
| Output supply voltage for AC-LVDS, AC-CML, AC-LVPECL, or HCSL driver | VDDO_x | 1.71 | 1.8 | 1.89 | V | AC-LVDS, AC-CML, AC-LVPECL, or HCSL driver, 1.8V option | 8 |
| Output supply voltage for AC-LVDS, AC-CML, AC-LVPECL, or HCSL driver | VDDO_x | 2.375 | 2.5 | 2.625 | V | AC-LVDS, AC-CML, AC-LVPECL, or HCSL driver, 2.5V option | 8 |
| Output supply voltage for AC-LVDS, AC-CML, AC-LVPECL, or HCSL driver | VDDO_x | 3.135 | 3.3 | 3.465 | V | AC-LVDS, AC-CML, AC-LVPECL, or HCSL driver, 3.3V option | 8 |
| Output supply voltage for 1.8V LVCMOS driver | VDDO_x | 1.71 | 1.8 | 1.89 | V | 1.8V LVCMOS driver | 8 |
| Input voltage range for clock and logic inputs | VIN | 0 | 3.465 | V | 8 | ||
| Ambient or operating temperature | TA | -40 | 85 | °C | 8 | ||
| Junction temperature | TJ | 125 | °C | 8 | |||
| Power supply ramp time | tVDD | 0.01 | 100 | ms | 8 | ||
| Total Current Consumption (all VDD and VDDO pins, 3.3V) | IDDPDN | 56 | 75 | mA | Device powered-down (PDN pin held low) | 10 | |
| Input frequency range (XO) | fIN | 10 | 100 | MHz | 10 | ||
| Single-ended input voltage swing (XO) | VIN-SE | 0.4 | 2.6 | Vpp | Single ended input, internal AC coupling | 10 | |
| Differential input peak to peak voltage swing (XO) | VIN-DIFF | 0.4 | 2 | Vpp | Differential input | 10 | |
| Differential input voltage swing (XO) | VID | 0.2 | 1 | /V/ | Differential input | 10 | |
| Input slew rate (XO) | dV/dt | 0.2 | 0.5 | V/ns | 10 | ||
| Input duty cycle | IDC | 40 | 60 | % | 10 | ||
| Input leakage (XO) | IIN | -350 | 350 | µA | 50Ω and 100Ω internal terminations disabled | 10 | |
| Input frequency range (PRIREF, SECREF) | fIN | 5 | 800 | MHz | Differential input | 10 | |
| Single-ended input voltage swing (PRIREF, SECREF) | VIN-SE | 0.4 | 2.6 | Vpp | AC-coupled input | 10 | |
| Differential input peak to peak voltage swing (PRIREF, SECREF) | VIN-DIFF | 0.4 | 2 | Vpp | Differential input, VHYST = 50mV | 10 | |
| Differential input peak to peak voltage swing (PRIREF, SECREF) | VIN-DIFF | 0.7 | 2 | Vpp | Differential input, VHYST = 200mV | 10 | |
| Differential input voltage swing (PRIREF, SECREF) | VID | 0.2 | 1 | V | Differential input, VHYST = 50mV | 10 | |
| Differential input voltage swing (PRIREF, SECREF) | VID | 0.35 | 1 | V | Differential input, VHYST = 200mV | 10 | |
| Input slew rate (PRIREF, SECREF) | dV/dt | 0.2 | 0.5 | V/ns | 10 | ||
| Input leakage (PRIREF, SECREF) | IIN | -350 | 350 | µA | 50Ω and 100Ω internal terminations disabled | 10 | |
| VCO2 Frequency Range | fVCO2 | 5500 | 6250 | MHz | 10 | ||
| AC-LVDS output voltage swing (VOH - VOL) | VOD | 250 | 390 | 450 | mV | 25MHz ≤ fOUT ≤ 800MHz; TYP at 156.25MHz | 11 |
| AC-LVDS output common mode | VOS | 100 | 430 | mV | 11 | ||
| AC-CML output voltage swing (VOH - VOL) | VOD | 400 | 600 | 800 | mV | 25MHz ≤ fOUT ≤ 800MHz; TYP at fOUT = 156.25MHz | 11 |
| AC-CML output common mode | VOS | 150 | 550 | mV | 11 | ||
| AC-LVPECL output voltage swing (VOH - VOL) | VOD | 450 | 780 | 1000 | mV | 25MHz ≤ fOUT ≤ 800MHz; TYP at fOUT = 156.25MHz | 12 |
| AC-LVPECL output common mode | VOS | 300 | 700 | mV | 12 | ||
| HCSL output high voltage | VOH | 600 | 880 | mV | fOUT ≤ 400MHz | 12 | |
| HCSL output low voltage | VOL | -150 | 150 | mV | 12 | ||
| 3-level logic input mid voltage | VIM | 0.7 | 0.9 | V | Input floating with internal bias and PDN pulled low | 13 | |
| 3-level logic input high current | IIH | -40 | 40 | µA | VIH = VDD | 13 | |
| DPLL bandwidth range | BW | 0.01 | 4000 | Hz | Programmed bandwidth setting | 15 | |
| Phase hit between two reference inputs | tHITLESS | -50 | 50 | ps | With 0ppm error; valid for a single switchover event between two clock inputs at the same frequency | 15 | |
| Frequency transient during hitless switch | fHITLESS | -10 | 10 | ppb | Valid for a single switchover event between two clock inputs at the same frequency | 15 | |
| RMS Phase Jitter (12kHz to 20MHz) | RJ | 50 | 80 | fs RMS | 625MHz AC-DIFF output from APLL1, fXO = 48MHz, fPD1 = fXO/2, fVCO1 = 2.5GHz | 14 | |
| RMS Phase Jitter (12kHz to 20MHz) | RJ | 60 | 90 | fs RMS | 156.25MHz AC-LVPECL output from APLL1, fXO = 48MHz, fPD1 = fXO/2, fVCO1 = 2.5GHz | 14 | |
| Junction-to-ambient thermal resistance (4-layer JEDEC) | RθJA | 23.3 | °C/W | 4-layer JEDEC standard PCB, 48 pins | 9 | ||
| Junction-to-case (top) thermal resistance (4-layer JEDEC) | RθJC(top) | 13.2 | °C/W | 4-layer JEDEC standard PCB, 48 pins | 9 | ||
| Junction-to-board thermal resistance (4-layer JEDEC) | RθJB | 7.4 | °C/W | 4-layer JEDEC standard PCB, 48 pins | 9 | ||
| Junction-to-case (bottom) thermal resistance (4-layer JEDEC) | RθJC(bot) | 1.4 | °C/W | 4-layer JEDEC standard PCB, 48 pins | 9 | ||
| Junction-to-top characterization parameter (4-layer JEDEC) | ψJT | 0.2 | °C/W | 4-layer JEDEC standard PCB, 48 pins | 9 | ||
| Junction-to-board characterization parameter (4-layer JEDEC) | ψJB | 7.3 | °C/W | 4-layer JEDEC standard PCB, 48 pins | 9 | ||
| Junction-to-ambient thermal resistance (10-layer custom PCB) | RθJA | 9.1 | °C/W | 10-layer custom PCB, 48 pins | 9 | ||
| Junction-to-board thermal resistance (10-layer custom PCB) | RθJB | 4.4 | °C/W | 10-layer custom PCB, 48 pins | 9 | ||
| Junction-to-board characterization parameter (10-layer custom PCB) | ψJB | 4.4 | °C/W | 10-layer custom PCB, 48 pins | 9 |
CAD (KiCad official)
- Symbol:
LMK05318BRGZT - Footprint:
Package_DFN_QFN:QFN-48-1EP_7x7mm_P0.5mm_EP5.15x5.15mm - 3D model: VQFN-48-EP(7x7) (KiCad packages3D, STEP)
- 3D model files:
lmk05318brgzt-etched.step/lmk05318brgzt-etched.glbcarry the MPN laser-etched on the die in a toggleableAdom.LaserEtchgroup (Fusion-ready);lmk05318brgzt.step/lmk05318brgzt.glbare the bare package body.
Provenance
Data extracted from the manufacturer datasheet, not a distributor listing:
- Datasheet: Texas Instruments datasheet (93 pp, sha256
5895e107ae544f96, retrieved 2026-10-30, tier: manufacturer) - Extractor: parts-factory
2.0.0/extract_pins 0.3, primaryclaude-haiku-5-5(text), consensusclaude-sonnet-5-5(agreed), guards: pin_guards 0.1: passed. Pins are checked against the footprint pad set and their cited datasheet pages before publish. - CAD: KiCad official libraries (CC-BY-SA 4.0).